Your 1998 GMC Jimmyproblems, repair costs and recalls
What we've documented about the 1998 GMC Jimmy: problems owners and shops report, typical repair and upkeep costs, and safety recalls.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems for your 1998 GMC Jimmy
13 documented issues apply to 1998, most serious first.
Automatic transmission slips or loses reverse
- What you'll notice
- The Jimmy hesitates or revs up between gears, slips in first or second, shifts late or harshly, or won't back up at all. A transmission that worked fine when cold may start slipping once it warms up.
- Why it happens
- The 4L60-E four-speed automatic used in the Jimmy wears internally with age, heat and towing. Common failure points include the reverse input clutch, worn clutch packs and a cracked or worn rear sun shell, which cause slipping and loss of gears.
- What to do
- Check the fluid level and smell with the engine running and warm. Burnt, dark fluid or metal in the pan means internal wear. Avoid towing or hard acceleration and get a transmission shop diagnosis; a rebuild or a remanufactured unit is the usual fix.
Intake manifold gaskets leak coolant
- What you'll notice
- The coolant level keeps dropping with no puddle under the truck, or you see coolant crust near the top of the engine. In bad cases the oil looks milky or the engine overheats.
- Why it happens
- The 4.3L Vortec uses intake manifold gaskets with plastic carriers that break down from DEX-COOL coolant and heat cycles. Coolant then seeps out externally or into the engine oil, which can ruin the bearings if ignored.
- What to do
- Keep an eye on the coolant level and check the oil dipstick for a milky look. Have the gaskets replaced with improved metal-frame versions soon, and change the oil afterward if coolant got into it.
Front ball joints wear out
- What you'll notice
- Clunking or popping from the front end over bumps, wandering steering, or uneven wear on the front tires.
- Why it happens
- The Jimmy's front ball joints carry a lot of weight and wear out, especially on 4x4 trucks. A badly worn joint can separate and let the wheel fold under.
- What to do
- Have the front end checked for play at your next tire rotation or sooner if it clunks. Replace worn ball joints promptly and get an alignment afterward.
Brake hose or lower control arm defect (recalls)
- What you'll notice
- A soft brake pedal or brake fluid leak, or a clunk or vague handling from the front suspension.
- Why it happens
- GM issued two small recalls on 1998 trucks: one for a brake hose that could leak and one for a front lower control arm problem that could affect control.
- What to do
- Check your VIN for open recalls; both repairs are free at a GMC dealer.
Free at a GMC dealer if not already done.
Rough running from the central 'spider' fuel injector
- What you'll notice
- The engine runs rough or shakes at idle, misfires, or the check engine light comes on with misfire codes. You may notice a fuel smell or a long crank after the truck has sat.
- Why it happens
- This engine feeds all six cylinders from one central injector unit with thin lines (the 'spider'). The poppet nozzles stick or leak with age, so some cylinders get too little or too much fuel.
- What to do
- Have a shop read the misfire codes and test fuel pressure and leak-down. If the spider injector is at fault, replace it with the updated multi-port style unit, which fixes the problem for good.
Fuel pump fails and engine won't start
- What you'll notice
- The engine cranks but won't fire, sputters at highway speed, or stalls and won't restart. You may not hear the usual hum from the fuel tank when you turn the key on.
- Why it happens
- The in-tank electric fuel pump wears out, often around 100,000 miles. A clogged fuel filter makes the pump work harder and shortens its life.
- What to do
- Have the fuel pressure tested before replacing parts. If the pump is weak, replace the pump module and the fuel filter together, and change the filter about every 30,000 miles after that.
ABS light on from failed brake control module
- What you'll notice
- The ABS warning light stays on. The regular brakes still work, but the anti-lock system is switched off, so the wheels can lock on slippery roads.
- Why it happens
- The electronic brake control module that runs the ABS fails internally on these trucks. A bad wheel speed sensor or corroded wiring can cause the same light.
- What to do
- Have the ABS codes read so you don't replace the wrong part. A rebuilt module is a common, cheaper fix; drive carefully in rain and snow until it's repaired.
Misfire from worn distributor cap and rotor
- What you'll notice
- Rough idle, stumbling under acceleration, and a flashing or steady check engine light, often worse in damp weather.
- Why it happens
- The 4.3L still uses a distributor. The cap and rotor wear and build up carbon tracks, and a loose rotor screw can damage the cap, so spark jumps to the wrong place.
- What to do
- Replace the cap and rotor (and the plug wires if they are old) with good-quality parts. It's an inexpensive repair that often clears misfires on these engines.
Dashboard gauges stick or stop working
- What you'll notice
- The speedometer, fuel, temperature or tach needle freezes, drops to zero or reads wrong, sometimes only now and then.
- Why it happens
- The tiny stepper motors that move the gauge needles in this instrument cluster wear out. It's a common problem across GM's 1998-and-later small trucks and SUVs.
- What to do
- A cluster repair shop can replace the gauge motors, which costs much less than a new cluster. Don't rely on a stuck temperature or fuel gauge in the meantime.
Fuel gauge reads wrong
- What you'll notice
- The fuel gauge reads empty on a full tank, sticks at one level, or swings around while you drive.
- Why it happens
- The fuel level sender in the tank wears where its contact rubs, or the gauge motor in the cluster fails.
- What to do
- Track your fill-ups with the trip meter so you don't run out. A shop can tell whether the sender or the gauge is at fault; the sender is part of the fuel pump module.
Heater fan works only on some speeds
- What you'll notice
- The blower works on high but not on the lower settings, or it quits altogether.
- Why it happens
- The blower motor resistor burns out, often because an aging blower motor draws too much current.
- What to do
- Replace the resistor, and the blower motor too if it's noisy or slow. It's a quick job behind the glove box area.
Oil pressure gauge drops or jumps around
- What you'll notice
- The oil pressure gauge falls to zero or swings around while the engine sounds normal.
- Why it happens
- The oil pressure sending unit at the back of the engine fails or leaks. Real low oil pressure is much less common, but it must be ruled out.
- What to do
- Check the oil level first. If the engine is quiet and full of oil, have a mechanical gauge test done; if pressure is fine, replace the sender.
Doors sag and are hard to close
- What you'll notice
- The doors drop when opened, rub or pop as they latch, and need to be lifted or slammed to close.
- Why it happens
- The door hinge pins and bushings wear out on these trucks, especially on the heavier driver's door.
- What to do
- Install a hinge pin and bushing kit. It's inexpensive and stops further wear on the striker and latch.
Repair prices for your 1998 GMC Jimmy
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Rebuild or replace 4L60-E automatic transmission
- Replace intake manifold gaskets and coolant
- Replace central (spider) fuel injector assembly
- Replace in-tank fuel pump module and fuel filter
- Replace front lower ball joints (both sides) and align
- Replace or rebuild ABS electronic brake control module
- Replace distributor cap, rotor and spark plug wires
- Rebuild instrument cluster or replace gauge motors
- Replace fuel level sender or pump module
- Replace blower motor resistor (and motor if worn)
- Replace oil pressure sender
- Replace door hinge pins and bushings (one door)
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Free dealer recall repairNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Checking the NHTSA recall database…