Your 2003 Honda S2000problems, repair costs and recalls
What we've documented about the 2003 Honda S2000: problems owners and shops report, typical repair and upkeep costs, and safety recalls.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems for your 2003 Honda S2000
14 documented issues apply to 2003, most serious first.
Engine damage from over-revving on a missed downshift
- What you'll notice
- A sudden loud mechanical noise after a downshift, followed by misfiring, ticking, low power, or an engine that will not run right.
- Why it happens
- These engines rev very high. Grabbing the wrong gear on a downshift (for example, second instead of fourth) can spin the engine far past redline, which can bend valves or damage the valvetrain. Oil starvation in hard track driving can also hurt the engine.
- What to do
- If you suspect an over-rev, stop driving and have a compression and leak-down test done. When buying a used S2000, ask a Honda-savvy shop to check for this.
Cracked valve spring retainers
- What you'll notice
- Ticking or clattering from the top of the engine, a misfire, or a cracked retainer found when the valves are adjusted.
- Why it happens
- The valve spring retainers used on early engines were weaker than the later design and can crack, especially after over-revs. A broken retainer can drop a valve into the engine.
- What to do
- Ask for the retainers to be inspected at the next valve adjustment. Many owners upgrade to the later 2.2L-style retainers as a precaution.
Burning oil on early cars
- What you'll notice
- The oil level drops between changes, sometimes a quart every 1,000 miles or worse, and you may see a puff of blue smoke at high revs.
- Why it happens
- Early 2.0L cars are known for using oil, especially when driven hard into the high-rpm VTEC range. Crankcase ventilation and piston oil-jet design play a part.
- What to do
- Check the dipstick at every fill-up and top up as needed. Running these engines low on oil is a common cause of failure. An oil catch can or updated oil-jet bolts help some owners.
Timing chain tensioner rattle
- What you'll notice
- A rattle or a sound like a playing card in bicycle spokes from the engine, often at idle or around 2,000-3,000 rpm.
- Why it happens
- The timing chain tensioner wears and stops holding the chain tight, so the chain slaps against its guides.
- What to do
- Have the noise checked soon. Replacing the tensioner is a fairly small job compared with the damage a loose chain can cause.
Grinding or notchy shifts into second gear
- What you'll notice
- Gears grind or feel notchy, mostly going into second or third and worst when the car is cold.
- Why it happens
- Wear on the synchronizers (the parts that match gear speeds before they engage) and old gear oil cause grinding. Honda issued service bulletins for grinding on upshifts and gear clash between first and second.
- What to do
- Change the manual transmission fluid with Honda MTF first and let the car warm up before shifting hard. If grinding stays, a shop may need to replace synchronizers.
Torn or worn convertible top
- What you'll notice
- Tears in the soft top, often at the lock handle or right rear corner, plus water dripping into the cabin in rain or a car wash.
- Why it happens
- The fabric folds at the same points every time the top goes down and wears through over the years. Honda issued bulletins for tears on 2005 and newer tops.
- What to do
- Small tears can be patched with fabric glue and a patch. Avoid automatic car washes. A worn top should be replaced before water damages the interior and electronics.
Heater blower motor overheats and blows its fuse
- What you'll notice
- The fan stops working, often suddenly, and the fuse is found blown. In bad cases the fan wheel melts.
- Why it happens
- The blower motor's cooling hose gets clogged, so the motor runs hot. Honda issued a service bulletin on this.
- What to do
- Replace the fuse once; if it blows again, have the blower and its cooling hose checked.
Hesitation under hard acceleration
- What you'll notice
- The engine stumbles or hesitates for a moment when you floor it, then picks up again.
- Why it happens
- Honda issued service bulletins for intermittent hesitation under hard acceleration on these years, addressed with diagnosis and updates.
- What to do
- Note when it happens and have a Honda-savvy shop check for the bulletin fix and for ignition or fuel problems.
Buzzing or noisy clutch pedal
- What you'll notice
- A buzz from the pedal area or transmission, especially when slowing down, or a clutch pedal that feels notchy or noisy.
- Why it happens
- The clutch release bearing and clutch parts transmit a vibration that can be heard in the cabin. Honda issued service bulletins for decel buzz and a noisy clutch pedal, and later redesigned the clutch.
- What to do
- This is usually harmless. If the noise grows, or the clutch starts slipping, have the clutch inspected.
Creaks and rattles from the closed top
- What you'll notice
- Squeaks, creaks or wind noise from the soft top when it is up and you drive over bumps.
- Why it happens
- The top's pivot points dry out and the lock handles can have play. Honda's fix was lubrication and shims at the lock handles.
- What to do
- Lubricate the pivot points and ask a shop to shim the latches. Hard-top style strikers also help some owners.
Whistling from the vents when A/C is on
- What you'll notice
- A high whistle from the dash vents whenever the air conditioning runs.
- Why it happens
- The A/C expansion valve, which meters refrigerant into the evaporator, can vibrate and whistle.
- What to do
- It is mostly an annoyance. A shop can replace the expansion valve if the noise bothers you.
Check engine light from a failed EVAP solenoid
- What you'll notice
- The check engine light comes on, often with an EVAP code, especially in areas that salt their roads in winter.
- Why it happens
- A solenoid in the fuel vapor (EVAP) system corrodes and fails.
- What to do
- Have the code read. It does not hurt the engine but will fail an emissions test.
Clicking or creaking from the rear axles
- What you'll notice
- A click or creak from the rear when pulling away in first or reverse, or a grunt at low speed.
- Why it happens
- The rear axle nuts were under-tightened from the factory spec, letting the axle shift in the hub. Honda updated the torque spec and issued bulletins for rear creaks.
- What to do
- Have the rear axle nuts torqued to Honda's updated spec. It is a quick, cheap fix.
Odometer overstates mileage
- What you'll notice
- The speedometer reads a bit high and the odometer adds miles faster than you really drove.
- Why it happens
- A class action found certain 2002-2006 Hondas overstated mileage. Honda extended warranties to make up for the extra miles.
- What to do
- Compare against GPS speed. Ask a Honda dealer whether your car got the mileage-related warranty extension.
Repair prices for your 2003 Honda S2000
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Cylinder head repair or engine replacement
- Install oil catch can or updated oil-jet bolts; monitor oil
- Valve adjustment and upgraded valve spring retainers
- Replace timing chain tensioner
- Replace transmission fluid; replace synchronizers if needed
- Replace clutch, release bearing and pressure plate
- Replace convertible soft top
- Lubricate top pivots and shim latches
- Replace heater blower motor and clear cooling hose
- Replace A/C expansion valve and recharge
- Replace EVAP solenoid
- Diagnose and apply bulletin fix
- Retorque rear axle nuts
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Checking the NHTSA recall database…