Your 2016 Hyundai Genesis Coupeproblems, repair costs and recalls
What we've documented about the 2016 Hyundai Genesis Coupe: problems owners and shops report, typical repair and upkeep costs, and safety recalls.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems for your 2016 Hyundai Genesis Coupe
16 documented issues apply to 2016, most serious first.
Engine knocking or sudden engine failure (rod bearings)
- What you'll notice
- A deep knock from the engine that gets louder with speed, a flashing check engine light or low oil pressure warning, and in the worst cases the engine stops and won't restart.
- Why it happens
- Owners of both engines report connecting-rod bearing failures, usually around 90,000 to 115,000 miles. Low oil level, long oil-change intervals and oil-pressure problems are the usual suspects. The Genesis Coupe was not part of Hyundai's engine-bearing recalls for other models.
- What to do
- If you hear a new knock, pull over and shut the engine off; driving on a failing bearing destroys the engine. Check the oil level, have it towed, and ask Hyundai whether any goodwill help applies to your VIN.
Timing chain rattle on cold start
- What you'll notice
- A rattle or chatter for a few seconds after a cold start that fades once the engine warms up.
- Why it happens
- On the 2013-2016 direct-injection V6, the timing chain tensioners, guides and cam phasers wear. Owners call it the most common weak spot of this engine.
- What to do
- Have a shop listen to it and check for cam timing codes. Fixing it early (chain, guides, tensioners and phasers) costs far less than repairing damage from a chain that jumps.
Passenger airbag sensor connector can come loose (recall)
- What you'll notice
- Usually no warning. The airbag light may come on.
- Why it happens
- The wiring connector for the front passenger seat occupant sensor can work loose when the seat moves. In a crash the passenger airbag would then fire at low power no matter who is sitting there.
- What to do
- Look up your VIN for recall 16V722000. The dealer secures the connector free.
Driver airbag bolts may be loose (recall)
- What you'll notice
- Usually no warning sign.
- Why it happens
- The bolts that hold the driver airbag to the steering wheel may not have been tightened enough, so it could come loose.
- What to do
- Check your VIN for recall 20V248000. The dealer inspects and tightens the bolts free.
Misfires and rough idle from intake valve carbon
- What you'll notice
- Rough idle, hesitation, reduced throttle response and a check engine light for misfires, usually from about 60,000 to 90,000 miles.
- Why it happens
- This V6 sprays fuel straight into the cylinders, so nothing washes the backs of the intake valves. Oil vapor bakes onto them and builds carbon that disturbs airflow.
- What to do
- Have a shop confirm misfires are not from plugs or coils first. If carbon is the cause, a walnut-blast cleaning of the intake valves usually fixes it.
Manual transmission grinds between gears
- What you'll notice
- Grinding going into a gear (often 2nd, 3rd or 5th), notchy shifts, or a gear that is hard to get into, especially when the transmission is cold or you shift fast.
- Why it happens
- The synchronizers that match gear speeds wear or were weak from new. Hyundai issued campaigns early on to replace the shift lever and change the gear oil, and some cars got replacement transmissions under warranty.
- What to do
- Ask a dealer whether the shift lever and fluid campaigns were done for your VIN. Fresh gear oil of the correct type helps many cars. Grinding that keeps getting worse means the synchros need repair.
Clutch pedal soft or sticking from master or slave cylinder
- What you'll notice
- The clutch pedal feels spongy, sticks to the floor, or the clutch won't fully release so gears grind or the car creeps. You may see fluid near the pedal or under the car.
- Why it happens
- The hydraulic clutch master and slave cylinders leak or wear out. They are among the most-reported repairs on this car.
- What to do
- Check the brake/clutch fluid reservoir. If the pedal stays down or you can't get into gear, don't drive it; have the clutch hydraulics inspected and bled or replaced.
Clutch slipping or worn out
- What you'll notice
- Engine revs climb without the car speeding up, a burning smell after hard driving, or a chattering or noisy clutch.
- Why it happens
- The clutch disc, pressure plate, flywheel and release bearing wear out, often around 70,000 to 100,000 miles and sooner with hard launches.
- What to do
- Get a quote that includes the flywheel and release bearing. Driving on a slipping clutch can damage the flywheel and raise the bill.
Oil leaks from the V6 oil filter housing, timing cover or sensor
- What you'll notice
- Oil spots under the car, a burning-oil smell, or oil on the engine around the oil filter, front cover, back of the engine or the oil pressure sensor.
- Why it happens
- Owners report a cracked oil filter housing, leaking timing chain cover, oil pressure sensor and rear main seal, mostly as the cars age past 80,000 to 100,000 miles.
- What to do
- Keep an eye on the oil level and have the leak located. Small leaks can wait a little, but oil dripping onto the exhaust can catch fire.
Coolant leaks and overheating on the V6
- What you'll notice
- Coolant smell, drips under the front of the car, low coolant warnings, or the temperature gauge climbing.
- Why it happens
- On the 2013-2016 V6, owners report water pump failures, thermostat housing leaks and overheating.
- What to do
- If the gauge climbs, pull over and shut off the engine. Don't open a hot radiator cap. Have the cooling system pressure-tested.
A/C blows warm from compressor or condenser failure
- What you'll notice
- The A/C blows warm, cycles on and off, or makes a whine from the compressor.
- Why it happens
- The A/C compressor and condenser are among the most-reported repairs on this car. Compressor pulley bearings fail, and the low-mounted condenser can be punctured by road debris.
- What to do
- Have a shop check for leaks with dye before just recharging. A recharge alone won't last if the condenser or compressor is leaking.
Keyless entry door handle button stops working
- What you'll notice
- Pressing the button on the outside door handle no longer locks or unlocks the car, even with the key fob nearby.
- Why it happens
- The touch button and proximity sensor in the door handle fail. This is the most-reported problem in one owner survey; the usual fix is a new door handle.
- What to do
- Use the fob buttons or the hidden key in the meantime. A shop or dealer can replace the handle.
Water leaks into the tail lights
- What you'll notice
- Fog or water inside the tail light lenses, and sometimes damp carpet in the trunk.
- Why it happens
- The tail light housings and their seals let water in. Owners list it among the most common repairs.
- What to do
- Have the seals replaced or the housings resealed. Water in the lights can make bulbs and sockets fail.
Weak battery or slow cranking
- What you'll notice
- Slow cranking, a no-start, or an immobilizer warning, especially after the car sits.
- Why it happens
- Several owners report original batteries failing early, plus loose battery cables and grounds.
- What to do
- Have the battery and charging system tested and check that the cable clamps are tight.
Check engine light from oxygen sensors
- What you'll notice
- Check engine light with oxygen sensor codes, sometimes with slightly worse fuel economy.
- Why it happens
- Oxygen sensors are one of the most-reported failures across both engines.
- What to do
- Have the codes read. Replacing the failed sensor usually clears it; check wiring first if codes return.
Whining from the serpentine belt idler pulley
- What you'll notice
- A whine or chirp from the front of the engine that changes with engine speed.
- Why it happens
- The bearing in the belt idler or tensioner pulley wears out.
- What to do
- Have the pulleys checked and replaced before one seizes and throws the belt.
Repair prices for your 2016 Hyundai Genesis Coupe
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace engine with used or remanufactured unit
- Replace timing chains, guides, tensioners and cam phasers
- Walnut-blast intake valve cleaning
- Gear oil change, or synchro repair / transmission replacement
- Replace clutch master and/or slave cylinder and bleed
- Replace clutch, flywheel and release bearing
- Replace leaking gasket, seal, housing or sensor
- Replace water pump or thermostat housing
- Replace A/C compressor or condenser and recharge
- Replace outside door handle with proximity sensor
- Reseal or replace tail light housing
- Replace 12V battery
- Replace oxygen sensor
- Replace idler and tensioner pulleys
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Recall repair at a Hyundai dealerNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Checking the NHTSA recall database…