Hyundai Genesisproblems, repair costs and recalls
Problems reported across 2009–2016. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
31 documented issues across all years, most serious first.
Brake control unit corrosion reduces braking (recall)
- What you'll notice
- The brake pedal feels soft or sinks further than usual, stopping takes longer, or the ABS and brake warning lights come on.
- Why it happens
- The factory brake fluid did not protect the hydraulic electronic control unit (the ABS/stability control pump and valve block) from internal corrosion. Corroded valves can reduce braking force. Hyundai recalled sedans built through March 2012 and later extended coverage on this unit to 15 years with unlimited miles.
- What to do
- Treat any soft pedal as urgent and do not drive the car until it is checked. Ask a Hyundai dealer to run your VIN for recall 13V-489 and the control unit warranty extension.
Free under the recall and the 15-year control unit warranty extension. Use only DOT 4 brake fluid afterward.
ABS module can short and catch fire (recall)
- What you'll notice
- Usually no warning at all. Some owners notice a burning smell, smoke from under the hood, or the ABS light coming on, even with the car parked.
- Why it happens
- Brake fluid can leak inside the anti-lock brake module and cause an electrical short, which can start a fire in the engine bay while driving or parked. This covers 2011-2015 Genesis Coupes and 2015-2016 Genesis sedans.
- What to do
- Park outside and away from buildings until the fix is done. Check your VIN for recalls 23V-651 (Coupe) or 21V-160 (sedan); the dealer installs a new fuse for free.
Free at a Hyundai or Genesis dealer.
Brake lights may not work (recall)
- What you'll notice
- Brake lights stay off when you press the pedal, cruise control will not switch off with the brake, the shifter can move out of Park without pressing the brake, or the push-button start acts up.
- Why it happens
- The brake light switch can fail internally, and on some sedans the brake light circuit itself can fail. Hyundai recalled the switch on 2009-2011 sedans and 2010-2011 Coupes, and separately repaired the stop lamp circuit on 2009-2011 sedans.
- What to do
- Have someone confirm your brake lights work. Check your VIN for recalls 13V-113 and 14V-713; both repairs are free.
Free under recall. Out of recall, a brake light switch is a small job of about an hour.
Engine shuts off while driving at low speed
- What you'll notice
- The engine suddenly cuts out, often at low speed or while turning, and the steering and brakes become heavy. It usually restarts, and often no warning light or code is stored.
- Why it happens
- No single cause has been confirmed. Owners and dealers have traced some cases to loose or corroded battery terminals and power connections, a failed engine-bay fuse box, or sensors, and many dealers could not reproduce it.
- What to do
- If it happens, steer and brake firmly to a safe stop and restart in Park. Have the battery terminals, main power leads and fuse box checked first, and keep a log of when it happens to help the shop.
Engine knocking or seized engine
- What you'll notice
- A deep knocking from the engine that gets louder with speed, low oil pressure warnings, or the engine locking up and stopping.
- Why it happens
- Owners report engines failing from internal wear, and Hyundai issued a service bulletin on testing connecting rod bearing clearance for these years. Low oil level or long oil-change intervals make bearing damage more likely.
- What to do
- Stop driving if you hear a new knock or see the oil light. Check the oil level, and ask a dealer whether the rod bearing bulletin or a warranty applies before paying for a new engine.
Windshield wipers stop working (recall)
- What you'll notice
- The wipers work only on and off, or stop completely.
- Why it happens
- A seal on the wiper motor cover can break down and let water corrode the motor's circuit board. Hyundai recalled 2012 Genesis sedans built through April 2012.
- What to do
- Do not drive in rain or snow without working wipers. Check your VIN for recall 16V-117.
Free under recall. A full wiper motor out of warranty is a costly part; ask for a written quote.
Starter solenoid can short and catch fire (recall)
- What you'll notice
- Usually no warning. Some cars may show starting problems, a burning smell or smoke from the engine bay.
- Why it happens
- Water can get into the starter solenoid and cause a short circuit, which can lead to an engine compartment fire.
- What to do
- Park outside and away from buildings until repaired. Check your VIN for recall 24V-107; dealers add a relay kit for free.
Free under recall.
Power seat motor can overheat (recall)
- What you'll notice
- A front power seat keeps moving or will not stop, a burning or electrical smell, or smoke from under a front seat.
- Why it happens
- If a front seat control switch sticks, the seat motor can keep running and overheat, which can start a fire.
- What to do
- If a seat keeps moving on its own, stop and turn the car off. Check your VIN for recall 26V-664 and park outside and away from other cars until the remedy is done.
Free under recall once the remedy is available.
Instrument cluster shows wrong speed or warning lights (recall)
- What you'll notice
- The 7-inch cluster shows the wrong speed, lights up every warning light at once, or fails to show a warning when it should.
- Why it happens
- A software fault in the instrument cluster on sedans built February-May 2015.
- What to do
- Check your VIN for recall 16V-575; the dealer updates the cluster software for free.
Free under recall.
Original tires can crack in the sidewall (recall)
- What you'll notice
- Cracks in the sidewalls of the factory tires, a bulge, or a sudden loss of air.
- Why it happens
- Some original Hankook Ventus S1 noble2 tires can develop sidewall cracks that may lead to a blowout.
- What to do
- Inspect the tire sidewalls. If your car still has these tires, check your VIN for recall 15V-864; dealers replace them with another brand for free.
Free under recall.
Water in tail lights causes wrong gear display (recall)
- What you'll notice
- The dash shows the wrong gear, the car is slow to go into gear, or it may move when you do not expect it.
- Why it happens
- Water can leak into the rear combination lamps and reach wiring that affects the gear display and engagement.
- What to do
- Always confirm the car is in Park and set the parking brake. Check your VIN for recall 15V-097.
Free under recall.
Passenger airbag sensor connector can come loose (recall)
- What you'll notice
- The airbag warning light or passenger airbag status light may act up, often after the passenger seat is moved. (Genesis Coupe.)
- Why it happens
- A connector for the passenger seat occupant sensor can work loose when the seat is moved, so the passenger airbag may deploy with the wrong force in a crash.
- What to do
- Check your VIN for recall 16V-722. Have the airbag light checked if it comes on.
Free under recall.
Car can move if started in gear (recall)
- What you'll notice
- On manual-transmission Coupes, the engine can start and the car can lurch if it is in gear without the clutch pressed.
- Why it happens
- A return spring in the ignition switch can break, which lets the starter work without the clutch interlock doing its job.
- What to do
- Always start the car in neutral with the parking brake set. Check your VIN for recall 24V-562.
Free under recall.
Rear differential bolts can loosen (recall)
- What you'll notice
- A clunk or vibration from the rear, especially when shifting or taking off, or a sudden loss of drive. (Manual-transmission Coupes.)
- Why it happens
- If the rear differential was misaligned at the factory, its mounting bolts can loosen and the driveshaft can disconnect.
- What to do
- Check your VIN for recall 15V-756 and have the rear differential checked if you hear new clunks.
Free under recall.
Driver airbag bolts may be loose (recall)
- What you'll notice
- Usually no sign. A rattle from the steering wheel hub is possible. (2016 Coupe.)
- Why it happens
- The driver airbag mounting bolts may not have been tightened enough, so the airbag could come loose from the steering wheel.
- What to do
- Check your VIN for recall 20V-248; dealers retighten the bolts for free.
Free under recall.
Cam timing (CVVT) codes and timing chain wear
- What you'll notice
- Check engine light with cam timing codes such as P0014 or P0017, rough running, rattle on start-up, or the engine cranking but not starting.
- Why it happens
- On the 2.0T Coupe, the cam phasers (CVVT units), timing chain or tensioner can wear or stick, throwing the cam timing out. Dirty or wrong-grade oil makes it worse.
- What to do
- Do not ignore cam timing codes. Change the oil with the correct grade and have the timing system inspected before the chain skips.
Excessive oil consumption
- What you'll notice
- You need to add oil between changes, or the low oil pressure light comes on before the next service.
- Why it happens
- Some 2012 owners report the engine burning oil faster than normal. Running the engine low on oil can damage bearings over time.
- What to do
- Check the dipstick every few fill-ups and keep a record. If it uses more than about a quart every 1,000-2,000 miles, ask the dealer for an oil consumption test.
Harsh or delayed shifts (8-speed automatic)
- What you'll notice
- Jerky or thumping upshifts, a flare in engine speed between gears, a delay when shifting into Drive or Reverse, or a sudden hard shift when accelerating.
- Why it happens
- The 8-speed automatic relies on learned clutch pressure data. Hyundai released several service bulletins with software updates and pressure data reprogramming to smooth the 2-3, 3-4 and 4-5 shifts and fix delayed engagement.
- What to do
- Ask a dealer to check for and apply the latest transmission software updates. If it slips or shows a gear ratio code, get a full transmission diagnosis.
Shudder or rough shifting (6-speed automatic)
- What you'll notice
- A shudder during light acceleration around 50-60 mph, a harsh shift out of Park, the shifter refusing to leave Park, or clunky, slapping shifts.
- Why it happens
- Hyundai issued service bulletins for these early Genesis sedans with transmission computer updates to reduce shudder and clutch-wear compensation, plus a fix for harsh or no shift out of Park.
- What to do
- Have a dealer check for the transmission software updates. Check the fluid level and condition, especially on higher-mileage cars.
Battery keeps going dead
- What you'll notice
- The car will not start after sitting a few days, even with a new battery.
- Why it happens
- Something keeps drawing power after the car is shut off. Owners report dealers blaming a faulty radio or a loose wiring connection that kept the alarm system awake.
- What to do
- Ask a shop for a parasitic draw test, which measures current with the car off and pulls fuses one at a time to find the circuit that is draining the battery.
Rough idle or stalling from a dirty throttle body
- What you'll notice
- Rough or hunting idle, stalling at stops, hard starting when cold, or a check engine light with an idle control code.
- Why it happens
- Carbon builds up in the throttle body and intake on the direct-injection V6, which can upset idle control. Some owners needed throttle body replacement and engine computer updates.
- What to do
- Ask a shop to clean the throttle body and relearn the idle. If codes keep returning, have it checked for a failing throttle body and software updates.
Sudden loss of all electrical power or no start
- What you'll notice
- The car goes completely dead, the clock and settings reset after shutting off, or it will not crank even though the lights may work.
- Why it happens
- Owners and dealers found loose battery terminal screws and a loose power lead nut at the under-hood fuse block. A few cases were traced to an aftermarket alarm or a failed engine computer.
- What to do
- Have the battery terminals and main fuse block connections checked and tightened before replacing expensive parts. Remove any aftermarket alarm if problems started after it was installed.
Parking brake warning light may not come on (recall)
- What you'll notice
- The parking brake light does not come on even though the parking brake is partly set, so you may drive with it dragging, which can cause a burning smell and worn brakes.
- Why it happens
- The parking brake switch can corrode and stop telling the dash the brake is applied.
- What to do
- Make sure the parking brake is fully released before driving. Check your VIN for recall 17V-359.
Free under recall.
Turbo wastegate actuator failure
- What you'll notice
- Loss of power, boost that will not build or overboost codes, a check engine light, and sometimes a rattle from the turbo.
- Why it happens
- Owners of the 2.0T Coupe report the wastegate actuator arm breaking or the boost control solenoid failing, which can mean a new turbo.
- What to do
- Have the boost control system checked. If the actuator arm has broken, stop driving hard so parts do not get pulled into the turbo.
Clutch slave or master cylinder failure
- What you'll notice
- The clutch pedal feels soft or sticks to the floor, the car is hard to shift, or brake fluid leaks near the bell housing or under the dash. (Manual Coupes.)
- Why it happens
- The hydraulic clutch slave and master cylinders are among the most-reported Coupe repairs.
- What to do
- Check the brake/clutch fluid reservoir. If the pedal sinks or fluid is leaking, have the clutch hydraulics replaced and bled.
No sound from the speakers
- What you'll notice
- The radio and navigation screen work, but sound cuts out from all speakers, sometimes on and off.
- Why it happens
- Hyundai issued a bulletin to replace the Lexicon premium audio amplifier for intermittent sound loss, and RepairPal notes the problem on navigation-equipped cars.
- What to do
- Have a dealer check whether the amplifier bulletin applies to your car before replacing the head unit.
Idle speed surges when cold
- What you'll notice
- The idle speed rises and falls when the engine is cold, the engine may run rough, and the check engine light can come on.
- Why it happens
- Hyundai issued bulletins replacing the throttle position sensor and updating the engine computer for cold-engine idle fluctuation and throttle sensor codes.
- What to do
- Have the codes read and ask the dealer about the throttle sensor and engine computer updates.
Clear coat peeling and paint chipping
- What you'll notice
- Clear coat peeling or yellowing on the bumpers and rocker panels (often on white sedans), or large chips flaking off the hood and roof on Coupes.
- Why it happens
- Owners describe the paint layers separating, with problems showing up around 30,000-80,000 miles and sometimes returning after repainting.
- What to do
- Photograph the damage and ask a dealer about paint warranty or goodwill. Get a repaint quote from a body shop that guarantees its work.
Engine revs hang between shifts
- What you'll notice
- On manual Coupes, engine speed drops slowly after you press the clutch, making shifts jerky.
- Why it happens
- The engine computer holds the throttle open briefly between shifts. Hyundai issued a bulletin with an engine computer reflash.
- What to do
- Ask a dealer for the engine computer update.
Water leaks into tail lights
- What you'll notice
- Fog or water pooled inside the tail lights or third brake light, and sometimes bulbs or LEDs failing. (Coupe.)
- Why it happens
- The tail light and third brake light housings and seals can let water in.
- What to do
- Have the lamp seals checked and replaced. Wet lamps can corrode wiring and should be fixed early.
Keyless door handle sensor stops working
- What you'll notice
- The door does not lock or unlock when you touch the handle with the smart key nearby. (Coupe.)
- Why it happens
- The proximity sensor or button in the door handle fails; it is one of the most-reported Coupe repairs.
- What to do
- Use the key fob buttons in the meantime and have the handle sensor diagnosed and replaced.
Repair prices for your Hyundai Genesis
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Diagnose stall; clean and tighten battery and power connections or replace fuse box
- Replace engine with used or remanufactured unit
- Transmission software update and clutch pressure relearn
- Transmission computer update and fluid check
- Parasitic drain test and repair of faulty circuit or radio
- Replace throttle position sensor / throttle body and update engine computer
- Clean or replace throttle body and relearn idle
- Refinish bumpers and rocker panels
- Clean and tighten battery terminals and fuse block power lead
- Replace turbocharger or wastegate actuator / boost control valve
- Replace timing chain, tensioner and cam phasers
- Engine computer reflash
- Replace clutch slave cylinder and bleed system
- Reseal or replace tail light housing
- Replace outside door handle with proximity sensor
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Inspect brake control unit, replace if corroded, flush brake fluidNo charge if your vehicle is included
- Install revised ABS module fuseNo charge if your vehicle is included
- Replace brake light switch / repair stop lamp circuitNo charge if your vehicle is included
- Replace wiper motor cover and sealNo charge if your vehicle is included
- Install starter relay kit in engine junction boxNo charge if your vehicle is included
- Front power seat recall repairNo charge if your vehicle is included
- Replace parking brake switchNo charge if your vehicle is included
- Update instrument cluster softwareNo charge if your vehicle is included
- Replace original tiresNo charge if your vehicle is included
- Install water-blocking pads in rear lampsNo charge if your vehicle is included
- Secure occupant sensor connectorNo charge if your vehicle is included
- Replace ignition lock switchNo charge if your vehicle is included
- Inspect and correct rear differential mountingNo charge if your vehicle is included
- Inspect and retighten driver airbag boltsNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.