Hyundai Santa Feproblems, repair costs and recalls
Problems reported across 2001–2026. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
42 documented issues across all years, most serious first.
Crankshaft position sensor can crack and stall the engine (recall)
- What you'll notice
- The engine cuts out while driving, will not restart, or starts only after cooling down, sometimes with a check engine light.
- Why it happens
- The crankshaft position sensor housing could crack, so the engine computer loses the signal it needs to run the engine. Hyundai recalled affected SUVs.
- What to do
- A stall in traffic is dangerous, so do not wait. Check your VIN for recall 03V-030 and have the sensor replaced.
Rear trailing arms rust and can break (recall)
- What you'll notice
- Clunking or knocking from the rear over bumps, the rear end feeling loose or wandering, or heavy rust visible on the arms ahead of the rear wheels.
- Why it happens
- In states that use road salt, the rear trailing arms could corrode until they weaken and fracture, which affects how the rear wheels stay in place. Hyundai recalled affected SUVs.
- What to do
- Have the rear suspension inspected right away and do not drive if the arms are badly rusted. Check your VIN for recall 09V-123.
Front coil springs rust and snap (recall)
- What you'll notice
- A loud bang or clunk from a front corner, the SUV sitting lower on one side, or a tire that suddenly goes flat.
- Why it happens
- Road salt can corrode the front coil springs until one breaks. A broken spring end can rub or cut into the tire. Hyundai recalled SUVs sold or registered in salt-belt states.
- What to do
- Stop driving and have the front suspension checked if you hear a bang or the SUV leans. Check your VIN for recall 14V-435, which covers inspection and spring replacement.
ABS kicks in at low speed and lengthens stops (recall)
- What you'll notice
- The brake pedal pulses or buzzes during gentle, slow stops on dry pavement and the SUV takes longer than expected to stop.
- Why it happens
- Electrical noise in a wheel speed sensor signal could make the anti-lock system think a wheel is locking when it is not, so it eases off the brakes. Hyundai recalled affected SUVs.
- What to do
- Leave extra stopping distance and get it fixed soon. Check your VIN for recall 04V-131.
Passenger airbag sensor may treat a child as an adult (recall)
- What you'll notice
- The passenger airbag status light shows the airbag as on when a small child or child seat is in the front seat.
- Why it happens
- The seat's occupant classification system could misjudge a small child as an adult, leaving the front passenger airbag active when it should be off. Hyundai recalled affected SUVs twice.
- What to do
- Keep children in the back seat. Check your VIN for recalls 05V-450 and 05V-527 and have the system recalibrated.
Fuel tank may leak (recall)
- What you'll notice
- A gasoline smell around the rear of the SUV or fuel drips or wet spots under the tank.
- Why it happens
- An internal baffle wall in the fuel tank could be made below specification, which could let the tank leak. Hyundai recalled affected SUVs.
- What to do
- Do not drive or park indoors if you smell fuel. Check your VIN for recall 06V-317.
ABS module can short from moisture (recall)
- What you'll notice
- The ABS or brake warning light comes on, or anti-lock braking stops working.
- Why it happens
- Moisture could get inside the anti-lock brake control module and cause an electrical short. Hyundai recalled affected SUVs.
- What to do
- Check your VIN for recall 20V-061 and get it repaired soon. If you ever smell burning from the engine bay, park outside and away from buildings until a dealer looks at it.
Brake light switch fails (recall)
- What you'll notice
- Brake lights that stay off or stay on, the shifter stuck in Park, cruise control not working, or stability control and check engine lights.
- Why it happens
- The stop lamp switch near the brake pedal can wear or lose contact. That switch also tells the shift lock and other systems when the brakes are pressed. Hyundai recalled the 2007 models and later the 2007-2011 models.
- What to do
- Drivers behind you may not see you braking, so get this fixed promptly. Check your VIN for recalls 09V-122 and 13V-113.
Driver airbag clock spring can fail (recall)
- What you'll notice
- The airbag warning light stays on, and the horn or steering wheel buttons may stop working.
- Why it happens
- The clock spring is the coiled wiring inside the steering column that connects the driver airbag. It could break, so the airbag might not deploy in a crash. Hyundai recalled affected SUVs.
- What to do
- Check your VIN for recall 11V-472 and have the clock spring replaced. Never ignore an airbag light.
Trailer hitch wiring module can overheat (recall)
- What you'll notice
- Smoke, a burning smell or melted wiring near the rear of the SUV, even when it is parked, or trailer lights acting up.
- Why it happens
- The trailer wiring module used with the tow package could let in moisture or suffer an internal short, which can overheat and start a fire. Hyundai recalled 2007-2008 and 2009-2011 SUVs with these harnesses.
- What to do
- Check your VIN for recalls 08E-055 and 11E-040. Until the repair is done, park outside and unplug the trailer harness.
Misaligned intermediate shaft can wear the transmission (recall)
- What you'll notice
- A grinding or whining noise from the transmission area, then a sudden loss of drive power.
- Why it happens
- An intermediate shaft could be installed out of alignment, which wears the transmission internally until it stops sending power to the wheels. Hyundai recalled affected SUVs.
- What to do
- Do not keep driving with a new grinding noise. Check your VIN for recall 11V-261.
Rear brake calipers can leak fluid (recall)
- What you'll notice
- A soft or sinking brake pedal, the brake warning light, or fluid wetness on the inside of a rear wheel.
- Why it happens
- Some rear brake calipers were not machined correctly and could leak brake fluid, which reduces braking power. Hyundai recalled affected SUVs.
- What to do
- Do not drive with a soft pedal or brake warning light. Check your VIN for recall 10V-613.
Rod bearing wear on the 2.4L four-cylinder
- What you'll notice
- A knock from the engine that gets faster as you rev it, the oil light, loss of power or stalling.
- Why it happens
- Connecting rod bearings in this engine can wear early and lead to engine seizure. The 2012 models were recalled, and 2010-2012 models were added to an engine settlement with knock-detection software and longer warranty coverage for bearing damage.
- What to do
- Stop driving if you hear a knock. Have a Hyundai dealer check your VIN for recall 20V-746 and the knock-detection software update, which must be done before a failure to keep the extended coverage.
Engine bearing failure and seizure
- What you'll notice
- A knock that rises with engine speed, the check engine or oil light, the engine dropping into reduced power, or stalling.
- Why it happens
- Machining debris or crankshaft surface flaws can starve the connecting rod bearings of oil until they wear and the engine seizes. Hyundai recalled the 2013-2014 Santa Fe Sport and some 2017 models, and added knock-detection software with lifetime short-block coverage for 2013-2018 Santa Fe Sport and some early 2019 models.
- What to do
- Stop driving if you hear knocking. Check your VIN for recalls 17V-226 and 17V-578 and make sure the knock-detection software update has been done.
High-pressure fuel pipe may leak after engine repair (recall)
- What you'll notice
- A strong gasoline smell from the engine bay, especially after an engine was replaced under an earlier recall.
- Why it happens
- On engines that were repaired or replaced under the bearing recalls, the high-pressure fuel pipe may not have been properly reinstalled and could leak fuel onto a hot engine. Hyundai recalled these SUVs.
- What to do
- Do not drive if you smell fuel under the hood. Check your VIN for recall 18V-934.
ABS control module fire risk (recall)
- What you'll notice
- Smoke or a burning smell from the engine bay, sometimes with the ABS light on, and it can happen while the SUV is parked and off.
- Why it happens
- The anti-lock brake control unit can develop an internal short. Recalls cover the 2013-2018 Santa Fe Sport, the 2016-2018 three-row Santa Fe, and the 2019 Santa Fe XL; the fix is a lower-rated fuse and module replacement if needed.
- What to do
- Check your VIN for recalls 23V-651 and 22V-056. Park outdoors and away from buildings until a dealer completes the repair.
Right front axle shaft can break (recall)
- What you'll notice
- A loud clunk, then the engine revs but the SUV does not move, or it rolls when left in Park.
- Why it happens
- The right front axle shaft could fracture, cutting power to the wheels. Without the parking brake set, a parked SUV could roll away. Hyundai recalled affected SUVs.
- What to do
- Always set the parking brake. Check your VIN for recall 13V-355.
Hood latch can rust and let the hood fly open (recall)
- What you'll notice
- The hood pops up while driving, does not close firmly, or the release feels stiff or sticky.
- Why it happens
- The cable for the secondary hood latch can corrode and bind, so the latch does not hold the hood if the main latch lets go. Hyundai recalled affected SUVs.
- What to do
- If the hood will not latch firmly, do not drive. Check your VIN for recall 17V-358.
Steering wheel may come loose (recall)
- What you'll notice
- Play or a clunk in the steering wheel itself, or the wheel feeling loose on the column.
- Why it happens
- The steering wheel could crack or separate from the steering column, causing loss of steering control. Hyundai recalled affected SUVs.
- What to do
- Do not drive if the steering wheel feels loose. Check your VIN for recall 18V-118.
Side curtain airbags can be damaged when they deploy (recall)
- What you'll notice
- Usually no warning signs.
- Why it happens
- The mounting bolts for the side curtain airbags could cut into the airbags as they inflate, reducing protection in a crash. Hyundai recalled affected SUVs.
- What to do
- Check your VIN for recall 18V-715 and have the dealer complete it.
Tow hitch wiring module fire risk (recall)
- What you'll notice
- A burning smell or smoke near the rear of the SUV, sometimes when it is parked and off.
- Why it happens
- Water can reach the circuit board in the trailer hitch wiring module and short it out. The module has constant power, so it can overheat even with the SUV off. Hyundai recalled affected SUVs, including hybrids and plug-in hybrids.
- What to do
- Check your VIN for recall 23V-181. Park outside and away from buildings until new wiring and a fuse are installed.
Fuel line connection may leak (recall)
- What you'll notice
- A gasoline smell from under the hood or wet fuel near the engine.
- Why it happens
- A fuel pipe connection on the engine might not have been tightened or seated properly at the factory and can leak, which raises the risk of fire. Hyundai issued two recalls.
- What to do
- Do not drive or park indoors if you smell fuel. Check your VIN for recalls 21V-308 and 21V-524.
Passenger airbag may not switch off for a child seat (recall)
- What you'll notice
- The passenger airbag status light shows on with a child seat in the front seat.
- Why it happens
- The occupant detection module might not recognize a rear-facing child seat, so the front passenger airbag stays armed. Hyundai recalled affected SUVs.
- What to do
- Put child seats in the back seat. Check your VIN for recall 21V-185.
Transmission oil pump fault can cause power loss (recall)
- What you'll notice
- A transmission warning, the SUV dropping into limp mode, or a sudden loss of drive power.
- Why it happens
- The transmission's oil pump can malfunction, and the backup limp mode may not work as intended, so the SUV can lose power. Hyundai recalled affected SUVs.
- What to do
- Get to a safe spot if a transmission warning appears. Check your VIN for recall 22V-746 and have it repaired before regular driving.
Turbo oil supply pipe can crack (recall)
- What you'll notice
- Oil spots under the front, a burning oil smell, or smoke from under the hood.
- Why it happens
- The pipe that feeds oil to the turbocharger can crack and spray oil in the engine bay, which can cause a fire or starve the turbo of oil. Hyundai recalled affected SUVs.
- What to do
- Stop and shut off the engine if you see smoke. Check your VIN for recall 22V-197.
SUV may roll away in Park (recall)
- What you'll notice
- The SUV creeps or moves after you shift into Park and get out.
- Why it happens
- A software error in the transmission control could keep the transmission from properly locking in Park. Hyundai recalled affected SUVs for a software update.
- What to do
- Always set the parking brake. Check your VIN for recall 24V-529 and get the update.
Floor wiring can chafe and affect airbags (recall)
- What you'll notice
- The airbag warning light comes on.
- Why it happens
- A wiring harness under the floor could rub against a nearby part until it is damaged, which could make airbags deploy unexpectedly or not deploy in a crash. Hyundai recalled affected SUVs.
- What to do
- Do not ignore an airbag light. Check your VIN for recall 24V-561.
Starter terminal cover can let the starter short (recall)
- What you'll notice
- A burning smell or smoke from the engine area, or the engine not cranking.
- Why it happens
- The protective cover on the starter motor's power terminal may not be installed properly, so the terminal can short against nearby metal and overheat. Hyundai recalled affected SUVs.
- What to do
- Check your VIN for recall 25V-659. If you smell burning, shut the SUV off and park it outside.
Connecting rod bolts may be loose (recall)
- What you'll notice
- A knocking noise from the engine, an oil leak, warning lights or a sudden loss of power.
- Why it happens
- Bolts holding the connecting rods might not have been tightened correctly at the factory, which can damage the engine. Hyundai recalled affected SUVs.
- What to do
- Stop driving if the engine starts knocking. Check your VIN for recall 25V-549.
Side curtain airbags may be installed wrong (recall)
- What you'll notice
- Usually no warning signs.
- Why it happens
- The side curtain airbags may not have been installed correctly, so they might not protect occupants as designed in a crash. Hyundai recalled affected SUVs.
- What to do
- Check your VIN for recall 25V-809 and have the dealer inspect it.
Front seat belt anchors may detach (recall)
- What you'll notice
- A front seat belt that feels loose at its lower mounting point, or a rattle near the base of a front seat.
- Why it happens
- The anchor holding the driver or passenger seat belt may not be secured properly and could come loose in a crash. Hyundai recalled affected SUVs.
- What to do
- Check your VIN for recall 26V-218 and have the anchors inspected promptly.
Instrument panel display may go blank (recall)
- What you'll notice
- The digital gauge cluster goes dark, so speed and warning lights are not shown.
- Why it happens
- A software error can cause the instrument panel display to stop working. Hyundai recalled affected SUVs for a software update.
- What to do
- Pull over safely if the gauges go blank. Check your VIN for recall 26V-047 and get the update.
Windshield may not be glued in properly (recall 21V-00M)
- What you'll notice
- Wind noise or a water leak at the top of the windshield, or glass that looks slightly out of place.
- Why it happens
- The windshield may have been bonded without the proper adhesive, so it can come out of the opening in a crash.
- What to do
- Have a dealer remove and reinstall the windshield under the recall; it is free and it matters for crash protection.
Crankshaft surface defect can wear the V6 bearings (recall 17V-578)
- What you'll notice
- A knock or rumble from deep in the engine, oil pressure or engine warning lights, and in bad cases the engine stalls and will not restart.
- Why it happens
- Machining marks on the crankshaft let the connecting rod bearings wear quickly, which starves them of oil film and damages the engine.
- What to do
- Have the VIN checked and the engine inspected; Hyundai replaces damaged engines free under the recall. Stop driving if the engine knocks.
Passenger airbag sensing needs recalibration (recall)
- What you'll notice
- The passenger airbag off light shows when a small adult is sitting in the front seat.
- Why it happens
- The occupant classification system under the passenger seat could fail to recognize a small adult and turn the passenger airbag off. Hyundai recalled affected SUVs for recalibration.
- What to do
- Check your VIN for recall 12V-354 and have the system recalibrated by a dealer.
Fuel gauge reads wrong from failed level sensors
- What you'll notice
- The fuel gauge drops to empty right after filling, sticks at one level or jumps around, often with the check engine light on.
- Why it happens
- These models use two fuel level sensors inside the tank, and their sensing contacts wear out. The engine computer then sees a bad reading and sets a fault code.
- What to do
- Track mileage between fill-ups so you do not run out of gas. A shop can confirm the code and replace the sensors; doing both at once is common because the job requires removing the rear seat.
Seat belt warning may not work (recall)
- What you'll notice
- No seat belt reminder chime or light when someone is unbuckled.
- Why it happens
- Wiring to the seat belt buckle could be damaged during assembly, so the system cannot tell whether the belt is fastened. Hyundai recalled affected SUVs.
- What to do
- Check your VIN for recall 16V-145 and make sure everyone buckles up in the meantime.
Oil consumption on the 2.4L direct-injection engine
- What you'll notice
- The oil level drops between changes, the oil light comes on, or the engine smokes or loses power when oil gets low.
- Why it happens
- Carbon can build up in the piston oil control rings on this engine, and a clogged PCV valve can make it worse, so the engine burns oil. Running low on oil can damage the bearings.
- What to do
- Check the dipstick every fill-up or two and top off as needed. Ask a dealer about Hyundai's oil consumption bulletin and the knock-detection update, and keep oil change receipts for warranty claims.
Rearview camera image may not appear (recall)
- What you'll notice
- A blank or frozen screen when shifting into Reverse.
- Why it happens
- A circuit board in the camera system can be damaged so the backup image does not display. Hyundai recalled affected SUVs.
- What to do
- Use your mirrors and look behind you when backing up. Check your VIN for recall 24V-879.
Backup camera image missing or blocked (recall)
- What you'll notice
- No camera picture in Reverse, or a trailer parking message covering the backup image.
- Why it happens
- Damage to the camera wiring harness can cut out the image, and on 2024 models a trailer parking assist message could cover the camera view. Hyundai issued recalls for both.
- What to do
- Look behind you and use mirrors when reversing. Check your VIN for recalls 25V-808 and 24V-246.
Front suspension and wheel bearing wear
- What you'll notice
- Clunks or rattles over bumps, a hum or growl from one wheel that gets louder with speed, steering that feels loose or wanders, and tires wearing unevenly.
- Why it happens
- Wheel bearings and hubs, ball joints, tie rod ends and the sway bar links and bushings on this generation wear out sooner than owners expect, and road salt speeds the wear up.
- What to do
- Have a shop check the front end and spin each wheel bearing. Worn joints and bearings become a safety problem once they are loose, so do not put the repair off.
Tire information label does not meet the standard (recall 03V-520)
- What you'll notice
- The sticker in the door opening does not give the tire and load information in the required form.
- Why it happens
- The labels printed for these years did not match the federal labelling rule, so owners can set tire pressures from wrong information.
- What to do
- Get the corrected label from a dealer and set the tires to the pressures it lists.
Repair prices for your Hyundai Santa Fe
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace crankshaft position sensor
- Replace rear trailing arm
- Replace front coil springs (pair)
- Reprogram ABS control unit
- Reprogram passenger occupant sensing unit
- Replace fuel tank
- Install ABS power relay per recall
- Replace brake light switch
- Replace airbag clock spring
- Update passenger airbag sensing software
- Replace trailer hitch wiring harness
- Replace both fuel level sensors
- Replace transmission output gear and intermediate shaft
- Replace rear brake caliper
- Replace engine long block
- Replace high-pressure fuel pipe
- Replace ABS fuse per recall
- Replace right front axle shaft
- Replace secondary hood latch cable
- Reroute seat belt buckle wiring
- Replace steering wheel assembly
- Install covers over side airbag mounting bolts
- Replace engine short block
- Install fuse and wiring kit for tow hitch module
- Tighten or replace fuel pipe connection
- Replace passenger occupant detection module
- Replace transmission and update software
- Replace turbocharger oil supply pipe
- Replace rearview camera
- Update transmission control software
- Inspect and repair floor wiring harness
- Replace backup camera wiring harness
- Inspect and reinstall starter terminal cover
- Replace engine
- Reinstall side curtain airbags
- Reinforce or replace front seat belt anchors
- Update instrument cluster software
- Install corrected tire information label
- Remove and reinstall windshield with new adhesive
- Inspect engine bearings, replace engine if damaged
- Replace front wheel hub/bearing assembly (one side)
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.