Your 2011 Jeep Wranglerproblems, repair costs and recalls
What we've documented about the 2011 Jeep Wrangler: problems owners and shops report, typical repair and upkeep costs, and safety recalls.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems for your 2011 Jeep Wrangler
4 documented issues apply to 2011, most serious first.
Death wobble front-end shake
- What you'll notice
- After hitting a bump at speed, the steering wheel and front end shake violently and do not stop until you slow way down.
- Why it happens
- The solid front axle depends on tight steering and suspension parts. Worn or loose track bar bolts and bushings, tie rods, ball joints or a weak steering damper can start a runaway shake. On 2018-2019 models Jeep offered a redesigned steering damper.
- What to do
- Slow down firmly without jerking the wheel. Have the track bar, its bolts and mounts, tie rods, ball joints and steering damper inspected and tightened or replaced before driving at speed again.
Lifter tick on the 3.8L V6 can end in engine damage
- What you'll notice
- A steady tick or clatter from the top of the engine, loudest on a cold start but often there when warm too. It can turn into a rough idle, a misfire code for one cylinder, and eventually a knock.
- Why it happens
- The valve lifters and their pushrods wear faster than they should. Once a lifter collapses it chews the matching camshaft lobe, and metal from that wear circulates through the oil.
- What to do
- Get the noise looked at quickly rather than living with it. Owners who waited have had to replace camshafts, heads or whole engines, and oil analysis or a camera through the pushrod hole can settle it early.
Fuse box module (TIPM) causes odd electrical faults
- What you'll notice
- Hard starting or no start, the fuel pump not running, or random problems with the horn, wipers, turn signals or lights.
- Why it happens
- The integrated power module that houses many fuses and relays can develop internal faults.
- What to do
- Have a shop test the module before replacing other parts. Repaired or updated modules are available.
3.8L V6 uses up engine oil between changes
- What you'll notice
- The dipstick reads low a long way before the next service, sometimes with a faint blue haze from the tailpipe or a burnt smell after a long climb. No puddle appears under the Jeep.
- Why it happens
- Oil gets past the piston rings and valve guides on this engine and is burned in the cylinders. A clogged crankcase breather valve makes it worse by pulling extra oil into the intake.
- What to do
- Check the oil at every fuel stop and top it up so it never runs low, and have the breather valve and plugs inspected. Ask a shop to run a measured oil consumption check before agreeing to any engine work.
Repair prices for your 2011 Jeep Wrangler
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace front track bar and inspect steering parts
- Replace TIPM with a rebuilt or new module
- Replace lifters, pushrods and camshaft
- Oil consumption test, then breather valve and spark plugs
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Checking the NHTSA recall database…