Your 1999 Mazda 626problems, repair costs and recalls
What we've documented about the 1999 Mazda 626: problems owners and shops report, typical repair and upkeep costs, and safety recalls.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems for your 1999 Mazda 626
19 documented issues apply to 1999, most serious first.
Automatic transmission slipping or failing
- What you'll notice
- Slipping or flaring between gears, harsh or late shifts, a whining noise, the O/D OFF light flashing, or no reverse. Some cars lose drive completely on the road.
- Why it happens
- The automatic transmissions in these 626s have a poor track record, and many owners and mechanics blame overheating of the fluid for wearing out the internal clutches. Failures are most often reported between about 50,000 and 120,000 miles.
- What to do
- Check the fluid level and smell right away; dark or burnt fluid is a bad sign. If it is slipping or will not engage, avoid hard driving and have a transmission shop diagnose it before damage gets worse.
Timing belt tensioner spring can break (recall)
- What you'll notice
- The engine can suddenly stall while driving. You may not notice anything before it happens.
- Why it happens
- An outside spring on the timing belt tensioner could break and get caught in the timing belt. Mazda recalled about 31,000 cars built from August 1997 to August 1998 (campaign 00V134).
- What to do
- Ask a Mazda dealer to check whether the tensioner was inspected or replaced. Because the timing belt drives the engine valves, keep up with timing belt changes too.
Free at a Mazda dealer. Ask the dealer to check your VIN for open recalls.
O/D OFF light flashing after highway driving
- What you'll notice
- The O/D OFF light on the dash starts flashing after a long highway drive or in hot weather, and shifting may feel different.
- Why it happens
- The transmission computer stores a fault code (P1783) when the transmission fluid gets too hot. Mazda issued a service bulletin about this condition. Repeated overheating shortens the life of the transmission.
- What to do
- Have the code read and the fluid checked and changed if it is dark. Ask about an auxiliary transmission cooler if you tow, drive in heat, or do long highway trips.
Brake fluid reservoir cap missing vent holes (recall)
- What you'll notice
- Usually nothing obvious at first; over time the brakes may feel less effective.
- Why it happens
- Some brake master cylinder reservoir caps were made on a worn tool and lacked vent holes, letting pressure in the reservoir drop and possibly reducing braking. Mazda recalled them (campaign 00V074).
- What to do
- Have a dealer inspect the reservoir cap and replace it if it is one of the bad ones. It is a quick, free fix.
Free at a Mazda dealer. Ask the dealer to check your VIN for open recalls.
Rough idle or stalling from idle air control valve
- What you'll notice
- Idle speed that is too low, hunts up and down, surges when the A/C cycles, or the engine stalls when you stop.
- Why it happens
- The idle air control (bypass air) valve gets dirty or fails with age, so the computer can no longer hold a steady idle. Worn plugs, a weak coil or a vacuum leak can cause similar symptoms.
- What to do
- Have codes read and the idle air valve tested and cleaned before replacing parts. Rule out vacuum leaks and ignition parts at the same time.
Low EGR flow code from clogged passages
- What you'll notice
- Check engine light with an EGR flow code (P0400 or P0401), sometimes with rough idle or pinging under load.
- Why it happens
- Carbon builds up in the small exhaust gas recirculation passages in the V6 intake, blocking the flow even when the EGR valve itself works.
- What to do
- Have the EGR valve tested first. If it is fine, the passages need to be cleaned, which means removing the throttle body and intake manifold.
Rough idle and hesitation with check engine light
- What you'll notice
- The 4-cylinder idles roughly and hesitates when you accelerate, with the check engine light on.
- Why it happens
- Mazda released a service bulletin (01500) for this condition on early-built 4-cylinder 626s. Owners also report misfires that come back after plugs and wires are replaced.
- What to do
- Have a shop read the codes and check for the bulletin. Also check plugs, wires, coil and vacuum hoses.
Water pump leak
- What you'll notice
- Coolant drips from the front of the engine, a sweet smell, and a coolant level that keeps dropping.
- Why it happens
- The water pump seal wears out with age. Mazda issued a bulletin on how to inspect these pumps for leaks. The pump sits behind the timing belt, so it is usually replaced with the belt.
- What to do
- Have the cooling system pressure tested. Replace the pump, timing belt and tensioner together to avoid paying for the same labor twice.
Clutch pedal sinks and will not release
- What you'll notice
- On manual-transmission cars, the clutch pedal goes soft or sinks to the floor and the car is hard to put in gear.
- Why it happens
- The seals inside the clutch master or slave cylinder wear out, so hydraulic pressure leaks away.
- What to do
- Check the clutch fluid reservoir for low fluid and look for leaks at the cylinders. Rebuilding or replacing the cylinder is usually enough.
Shifter can leave Park without pressing the brake
- What you'll notice
- You can move the shift lever out of Park without your foot on the brake pedal.
- Why it happens
- The brake shift interlock, which should lock the lever in Park until the brake is pressed, can be disabled by mistake. Mazda issued a bulletin (0400502) covering 1996-2002 626s.
- What to do
- Have the interlock checked and repaired. Until then, always press the brake firmly before shifting.
Vacuum leak causing rough running
- What you'll notice
- Rough or high idle, hesitation, a hissing sound under the hood, and a check engine light with lean codes.
- Why it happens
- Rubber vacuum hoses and intake connections harden and crack with age, letting unmetered air into the engine and upsetting the fuel mixture.
- What to do
- A smoke test quickly finds the leak. Replacing cracked hoses is usually cheap.
Check engine light with oxygen sensor codes P1131/P1132
- What you'll notice
- The check engine light comes on with codes P1131 or P1132, often with no change in how the car drives.
- Why it happens
- Mazda issued service bulletins for these codes on 1998-1999 626s. Some cars set them repeatedly even after oxygen sensors were replaced.
- What to do
- Ask a dealer or shop to check for the bulletin fix before buying parts. Replace an oxygen sensor only if testing shows it is slow or dead.
Coolant leak at engine block heater
- What you'll notice
- Drips of coolant under the front of the car and a slowly dropping coolant level.
- Why it happens
- On 4-cylinder cars fitted with a block heater, coolant can seep where the heater sits in the engine block. Mazda covered this in a service bulletin.
- What to do
- Find the source of the leak before topping up again. Low coolant can lead to overheating.
Coolant reservoir cracks and leaks
- What you'll notice
- Coolant puddles near the overflow bottle or the level drops with no obvious leak elsewhere.
- Why it happens
- The plastic coolant reservoir cracks with age and heat. One V6 owner reported replacing it several times.
- What to do
- Replace the cracked bottle and refill with the right coolant. Check that the radiator cap holds pressure.
Groaning from front strut mounts in turns
- What you'll notice
- A groan, creak or squeak from the front when turning the steering at low speed or over bumps.
- Why it happens
- The front strut mounts and their bearings wear out, and Mazda also issued a bulletin for steering squeak noises.
- What to do
- Have the strut mounts and struts inspected. Mounts are usually replaced along with the struts.
Musty smell from A/C vents
- What you'll notice
- A musty or mildew smell when the A/C or fan first comes on.
- Why it happens
- Moisture stays on the A/C evaporator and mold grows on it. Mazda has issued several bulletins on this odor.
- What to do
- Have the evaporator cleaned and the cabin drain checked. Running the fan without A/C for a few minutes before parking helps.
Sunroof stuck, binding or noisy
- What you'll notice
- The sunroof does not open or close, moves slowly, or makes grinding noises.
- Why it happens
- Mazda issued bulletins for sunroofs that bind or stop working on these years, mainly from the track and drive parts.
- What to do
- Have the tracks cleaned and lubricated first. If the motor is bad it needs to be replaced.
Horn not working or stuck on
- What you'll notice
- The horn does not sound, or it sounds on its own and will not stop.
- Why it happens
- Mazda issued a service bulletin (00800) for horns that stop working or stay on, related to the horn switch and its circuit.
- What to do
- If it is stuck on, pull the horn fuse and have the switch and relay checked.
Rear drum brake squeal
- What you'll notice
- A high-pitched squeal from the rear wheels when braking.
- Why it happens
- Mazda issued a bulletin (00199) for rear drum brake squeal on early-built cars, linked to the brake shoe lining.
- What to do
- Have the rear brakes inspected and fitted with updated shoes if needed.
Repair prices for your 1999 Mazda 626
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace automatic transmission with rebuilt or used unit
- Diagnose code and change transmission fluid
- Clean or replace idle air control valve
- Find and replace leaking vacuum hoses
- Clean EGR passages and replace intake gaskets
- Diagnose and apply bulletin fix or replace oxygen sensor
- Diagnose, apply bulletin repair, replace plugs and wires as needed
- Reseal or replace engine block heater
- Replace water pump with timing belt and tensioner
- Replace coolant reservoir
- Replace clutch master or slave cylinder and bleed
- Replace front strut mounts and struts
- Clean A/C evaporator and check drain
- Service sunroof tracks or replace sunroof motor
- Repair horn switch or replace horn relay
- Inspect and repair brake shift interlock
- Replace rear brake shoes and service drums
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Inspect and replace timing belt tensioner under recallNo charge if your vehicle is included
- Inspect and replace brake reservoir cap under recallNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Checking the NHTSA recall database…