Your 2005 Mazda B-Seriesproblems, repair costs and recalls
What we've documented about the 2005 Mazda B-Series: problems owners and shops report, typical repair and upkeep costs, and safety recalls.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems for your 2005 Mazda B-Series
20 documented issues apply to 2005, most serious first.
Takata airbag inflators can rupture (recall)
- What you'll notice
- Usually no warning. In a crash, the driver or passenger airbag inflator can burst and throw metal fragments at the people inside.
- Why it happens
- The Takata inflators in these trucks can build too much pressure when they deploy. Mazda recalled 2004-2006 B-Series trucks for both front airbags, and told owners of 2006 trucks not to drive them until repaired (campaigns 17V806, 17V807, 18V038, 18V039).
- What to do
- Stop driving the truck and contact a Mazda dealer to check your VIN for open recalls. The fix is free and Mazda can arrange towing.
Free at a Mazda dealer. Ask the dealer to check your VIN for open recalls.
Replacement airbag inflator installed backward (recall)
- What you'll notice
- No symptoms. In a crash, the passenger airbag might not inflate as designed.
- Why it happens
- During earlier Takata recall repairs, some replacement passenger inflators were installed the wrong way around. Mazda recalled about 12,700 trucks to check and reinstall them (campaign 23V837).
- What to do
- Even if your truck already had the Takata repair, check your VIN and book the free inspection.
Free at a Mazda dealer. Ask the dealer to check your VIN for open recalls.
Timing chain rattle on the 4.0L SOHC
- What you'll notice
- A rattling or buzzing from the engine, loudest on cold starts and around 2,400-3,000 rpm. Later, a check engine light or rough running.
- Why it happens
- The plastic timing chain guides and tensioners wear out and break. Early engines had poorly designed guides; later ones wear at high miles. A broken guide can drop debris into the oil pan and let a chain fail.
- What to do
- Do not ignore the rattle. Have a shop confirm which chain is noisy. Ford released a redesigned front cassette; fixing the rear chain needs the engine pulled, so earlier is cheaper.
Rusted brake lines leaking
- What you'll notice
- Brake fluid wetness near a wheel or under the truck, a soft or sinking brake pedal, or the brake light on.
- Why it happens
- Steel brake lines rust through, especially in road-salt states. Brake lines are one of the top repairs owners report.
- What to do
- If the pedal goes soft, do not drive. Have all lines inspected, since others are usually close to failing too.
Automatic transmission hard shifts or no reverse
- What you'll notice
- Harsh or delayed shifts, trouble shifting, or reverse stops working.
- Why it happens
- Owners report automatic transmissions on high-mileage trucks losing reverse and shifting hard as internal parts wear.
- What to do
- Check fluid level and condition first. Have a transmission shop diagnose it before it fails completely.
Worn ball joints and control arms
- What you'll notice
- Clunking over bumps, wandering steering, uneven tire wear, or a front end that feels loose.
- Why it happens
- Ball joints are the most reported repair on these trucks, wearing out along with the control arm bushings and tie rod ends.
- What to do
- Have the front end checked for play. A badly worn ball joint can separate, so do not put it off.
Front wheel bearing noise
- What you'll notice
- A humming or grinding noise that rises with speed, sometimes with a wobble or play in the wheel.
- Why it happens
- The front wheel bearings and hubs wear out, sometimes early when water gets into them.
- What to do
- Have the wheel checked for play. A failed bearing can lock up or let the wheel wobble.
Rusted frame and leaf spring hangers
- What you'll notice
- Clunks from the rear, the bed sitting crooked, or visible rust and flaking around the rear spring shackles and frame.
- Why it happens
- Owners report rotted rear leaf spring shackles, brackets and frame sections on these trucks, mostly in rust-belt states.
- What to do
- Have the frame and spring mounts inspected from underneath. Badly rotted mounts can fail and need welding or replacement.
In-tank fuel pump failure
- What you'll notice
- The truck cranks but will not start, or it sputters and dies, especially when hot or low on fuel.
- Why it happens
- The electric fuel pump inside the tank wears out. It is among the commonly reported repairs.
- What to do
- Listen for the pump hum when you turn the key, and have fuel pressure tested before replacing it.
Clutch slave cylinder leaking
- What you'll notice
- On manual trucks, the clutch pedal goes soft, sinks, or the truck is hard to shift and grinds.
- Why it happens
- The clutch slave cylinder leaks. On these trucks it sits inside the bell housing, so the transmission has to come out to replace it.
- What to do
- Check the clutch fluid level. If it keeps dropping, replace the slave cylinder and usually the clutch at the same time since the labor is the same.
Plastic thermostat housing leaks coolant
- What you'll notice
- Coolant drips or crusty residue near the thermostat at the front of the engine, and low coolant.
- Why it happens
- The plastic thermostat housing can split at its seam with age and heat.
- What to do
- Replace the housing and thermostat and top up the coolant before the engine overheats.
Radiator leak and overheating
- What you'll notice
- The temperature gauge rising, coolant under the front of the truck, or steam from the grille.
- Why it happens
- The radiator develops leaks with age, and hoses and fittings crack.
- What to do
- Stop if the engine overheats. Have the cooling system pressure tested and the leak fixed.
Driveshaft U-joint wear and clunk
- What you'll notice
- A clunk when shifting into gear or taking off, or a vibration at speed.
- Why it happens
- Driveshaft universal joints wear out and the slip joint can dry out.
- What to do
- Have the U-joints checked for play and greased. A failed U-joint can let the driveshaft drop.
Cracked PCV hose causes check engine light
- What you'll notice
- Check engine light with lean codes, rough idle, or a whistling sound.
- Why it happens
- The crankcase ventilation (PCV) hose cracks with age and lets in air the engine computer does not expect.
- What to do
- Have the PCV hose inspected during diagnosis. It is a cheap part.
Oil pressure gauge erratic or reading wrong
- What you'll notice
- The oil pressure gauge drops to zero, flickers or reads high while the engine runs normally.
- Why it happens
- The oil pressure sending unit fails, giving false readings.
- What to do
- Have real oil pressure checked with a mechanical gauge first. If pressure is fine, replace the sender.
Check engine light from EGR valve or DPFE sensor
- What you'll notice
- Check engine light with an EGR code, rough idle, or pinging when accelerating.
- Why it happens
- The exhaust gas recirculation valve, its tube, or the pressure sensor that monitors it (DPFE) fails or clogs.
- What to do
- Have the code read and the DPFE sensor tested; it is often the cheap part at fault.
Rear differential pinion seal leak
- What you'll notice
- Gear oil wetness on the front of the rear axle and drips under the truck.
- Why it happens
- The pinion seal where the driveshaft meets the axle wears out.
- What to do
- Check the axle oil level and replace the seal before the gears run low on oil.
Blower works only on high or not at all
- What you'll notice
- The heater and A/C fan works only on the top setting, or not at all.
- Why it happens
- The blower motor resistor fails, cutting out the lower fan speeds.
- What to do
- Replace the resistor; if the fan does not run on any speed, have the motor and fuse checked.
A/C blowing warm
- What you'll notice
- The air conditioning blows warm or only cool, and the compressor clutch may not engage.
- Why it happens
- A/C compressors, clutches, relays and hoses wear out and leak refrigerant with age.
- What to do
- Have the system leak-tested and the compressor clutch and relay checked before replacing the compressor.
No-start from worn starter or weak battery
- What you'll notice
- A click or slow crank when you turn the key, or nothing at all.
- Why it happens
- Starters and batteries wear out on these trucks; owners report replacing both after no-starts.
- What to do
- Have the battery and charging system tested first, then the starter.
Repair prices for your 2005 Mazda B-Series
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace timing chains, guides and cassettes
- Replace ball joints (one side)
- Replace front wheel bearing or hub assembly
- Replace rusted brake lines and bleed system
- Replace in-tank fuel pump assembly
- Replace clutch slave cylinder (and clutch)
- Replace PCV hose
- Replace thermostat housing and thermostat
- Replace radiator
- Replace oil pressure sending unit
- Replace EGR valve or DPFE sensor
- Replace pinion seal
- Replace U-joints and grease driveshaft slip joint
- Replace blower motor resistor
- Repair A/C (hose or clutch) or replace compressor
- Replace starter
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Replace driver and passenger airbag inflators under recallNo charge if your vehicle is included
- Inspect and reinstall passenger inflator under recallNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Checking the NHTSA recall database…