Your 2000 Mazda Milleniaproblems, repair costs and recalls
What we've documented about the 2000 Mazda Millenia: problems owners and shops report, typical repair and upkeep costs, and safety recalls.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems for your 2000 Mazda Millenia
16 documented issues apply to 2000, most serious first.
Supercharger oil seal leak and blue smoke
- What you'll notice
- Puffs of blue-gray smoke from the tailpipe, especially right after a cold start, and the oil level dropping quickly between changes. Oil may be visible in the intake ducts or around the supercharger pulley.
- Why it happens
- The Millenia S uses a Lysholm screw-type supercharger whose internal oil seals are fragile. When they wear out, engine oil gets pulled into the intake and burned. Owners note the blower can still sound normal and make full boost while it is leaking.
- What to do
- Check the oil level often and top it up so the engine is never run low. Have a shop look inside the intake for oil. A rebuilt supercharger is the usual fix; when it is replaced, the intercooler and pipes should be flushed and the PCV system checked.
Automatic transmission slipping, stuck in gear or HOLD light flashing
- What you'll notice
- The transmission stays in one gear (often first), shifts harshly or slips, and the HOLD or TCS lights may flash. Some owners hear a bang on shifts. Turning the car off and back on can clear it temporarily.
- Why it happens
- The Millenia's 4-speed automatic can develop internal wear or electronic control faults. When the computer sees a problem it puts the transmission in a limp mode, which is what the flashing HOLD light signals.
- What to do
- Have the transmission computer codes read and check the fluid level and condition. Avoid hard driving until it is diagnosed. A sensor, solenoid or wiring fault is cheaper to fix than a worn-out transmission, which may need a rebuild or a used replacement.
Valve cover gasket leak causing misfires
- What you'll notice
- Oil seeping around the top of the engine, a burning-oil smell, and a rough or stumbling engine when you accelerate. The check engine light may flash.
- Why it happens
- The valve cover gaskets harden with age. Oil then runs into the spark plug wells and soaks the plugs and boots, which causes misfires under load. Mazda issued a bulletin on valve cover oil leaks for these cars.
- What to do
- Have the valve cover gaskets and spark plug tube seals replaced, and clean or replace any oil-soaked plugs and boots at the same time.
EGR valve failure with shaking and check engine light
- What you'll notice
- The check engine light comes on, often with an EGR code such as P0400, and the car may shake or run rough, getting worse at highway speeds.
- Why it happens
- The exhaust gas recirculation (EGR) valve sticks or fails. It sits at the back of the V6, which makes it hard to reach and raises the labor cost.
- What to do
- Have the codes read and the EGR valve and its vacuum lines tested before replacing parts. Cracked vacuum lines can cause the same code and are much cheaper to fix.
Oxygen sensor failure and check engine light
- What you'll notice
- The check engine light stays on, sometimes with a code for an oxygen sensor (such as P0154), and fuel economy may drop. The car can fail a state emissions inspection.
- Why it happens
- The upstream oxygen sensors on this V6 wear out and their built-in heaters fail. Some owners have had to replace the same sensor more than once.
- What to do
- Have the codes read to confirm which sensor is at fault, and check its wiring. Replace failed sensors with good-quality parts so the light does not come back.
Knock sensor code P0325 turns on check engine light
- What you'll notice
- The check engine light comes on with code P0325. The car usually drives normally, though power can feel slightly down.
- Why it happens
- Mazda issued bulletins for check engine lights caused by knock sensor code P0325 on these cars. The knock sensor sits in the valley of the V6 under the intake, so a fault in the sensor or its wiring takes a lot of labor to reach.
- What to do
- Have a Mazda-savvy shop check the bulletin fix and test the sensor wiring first. If the sensor itself must be replaced, plan for several hours of labor.
Misfire codes P0300-P0306 and rough running
- What you'll notice
- A rough idle or stumbling, a flashing or steady check engine light, and misfire codes from P0300 to P0306.
- Why it happens
- Mazda put out a service bulletin for misfire codes on the Millenia. Fouled spark plugs, oil in the plug wells and tired ignition parts are common causes on these aging V6 engines.
- What to do
- Have the codes read and the plugs, wires and plug wells inspected. Don't drive hard with a flashing check engine light, as raw fuel can overheat the catalytic converter.
Water pump coolant leak
- What you'll notice
- Coolant drips or dried coolant crust at the front of the engine, a sweet smell, and the coolant level dropping. The temperature gauge may climb if it gets low.
- Why it happens
- The water pump seal wears and starts weeping. Mazda issued an inspection procedure for water pump leaks on these cars. The pump is driven by the timing belt, so getting to it is a big job.
- What to do
- Keep the coolant topped up and have the leak confirmed. Replace the water pump together with the timing belt and tensioner to save on labor.
Clunking or knocking from the front suspension
- What you'll notice
- A knock, thump or clunk from the front end when going over bumps, or squeaks and scraping when turning the wheel.
- Why it happens
- Mazda issued a bulletin for knocking or clunking noises from the front suspension. Worn bushings, links and strut parts are common on cars this age.
- What to do
- Have the front suspension inspected for worn links, bushings and strut mounts. Replace worn parts in pairs so the car handles evenly.
Whining or ringing noise inside the car
- What you'll notice
- A whine or ringing sound heard inside the cabin while driving.
- Why it happens
- Mazda issued bulletins for a whine or ringing noise that was traced to the transmission and a related cable.
- What to do
- Ask a Mazda dealer or specialist about the bulletin fix. It is usually a nuisance rather than a sign of transmission failure.
Tilt steering wheel stuck or not working
- What you'll notice
- The power tilt steering wheel will not move, or it gets stuck in the up position.
- Why it happens
- Mazda issued bulletins for an inoperative tilt steering wheel and one stuck in the up position.
- What to do
- Have the tilt motor, switch and wiring checked. Make sure the wheel is in a safe driving position before you drive.
Musty or mildew smell from the A/C vents
- What you'll notice
- A musty, moldy smell from the vents when the air conditioning is running, sometimes with a noisy blower.
- Why it happens
- Moisture stays on the A/C evaporator and lets mold and debris build up. Mazda issued several bulletins on A/C odor and blower noise for these cars.
- What to do
- Replace the cabin filter if fitted and have the evaporator cleaned with an approved treatment. Turning off the A/C a few minutes before you park helps it dry out.
Low fuel light on but tank only takes 10-13 gallons
- What you'll notice
- The low fuel warning comes on, but when you fill up the tank only takes about 10 to 13 gallons.
- Why it happens
- Mazda issued a bulletin for this low fuel warning that comes on too early on some cars.
- What to do
- Track your mileage between fill-ups to learn your real range, and ask a Mazda dealer about the bulletin fix for the fuel gauge sender.
Highway speed surge on S models
- What you'll notice
- On the highway at 55 to 70 mph, the car gently surges up and down by 1 to 3 mph without you changing the pedal.
- Why it happens
- Mazda issued a bulletin for Millenia S models that surge slightly at steady highway speeds.
- What to do
- Ask a Mazda dealer or specialist about the bulletin fix. Also have vacuum lines and the throttle body checked, since leaks and dirt can make it worse.
Evaporative system code P1455 turns on check engine light
- What you'll notice
- The check engine light comes on with code P1455. The car drives normally.
- Why it happens
- Mazda issued bulletins for check engine lights caused by an evaporative emissions (fuel vapor) system fault, code P1455.
- What to do
- Make sure the gas cap is tight and the seal is not cracked. If the light returns, have the vapor system smoke-tested for leaks.
Rattling noise from the exhaust system
- What you'll notice
- A tinny rattle from under the car, often at idle or at certain engine speeds.
- Why it happens
- Mazda issued a bulletin for rattling from the exhaust system. Loose heat shields and worn hangers are typical causes.
- What to do
- Have the exhaust checked for loose shields, clamps and hangers. Also check for leaks, since exhaust fumes should not get into the cabin.
Repair prices for your 2000 Mazda Millenia
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace supercharger with rebuilt unit, flush intercooler piping
- Replace automatic transmission with used or rebuilt unit
- Replace both valve cover gaskets and plug tube seals
- Replace EGR valve
- Replace upstream oxygen sensor
- Replace knock sensor (under intake manifold)
- Replace spark plugs and ignition wires, clean plug wells
- Replace water pump with timing belt and tensioner
- Replace front stabilizer links and bushings
- Apply Mazda bulletin fix (cable/insulator)
- Repair tilt motor or switch
- Clean A/C evaporator and treat for odor
- Apply bulletin fix and check vacuum lines
- Smoke-test vapor system; replace gas cap or vent part
- Secure or replace heat shields and hangers
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Checking the NHTSA recall database…