Mercedes-Benz M-Class / GLEproblems, repair costs and recalls
Problems reported across 1998–2024. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
35 documented issues across all years, most serious first.
7-speed automatic shifts harshly or goes into limp mode
- What you'll notice
- Hard or clunky shifts, especially 1-2, 3-2 and 2-1 when cold, slipping, or the transmission getting stuck in one gear with a warning on the dash.
- Why it happens
- The 7-speed automatic's internal control unit (often called the conductor plate) and its speed sensors fail with heat and age. Outdated shift software and worn internal parts cause rough shifting too.
- What to do
- Have the transmission codes read. A software update fixes some cases; a failed conductor plate or valve body is replaced without removing the whole transmission. Change the fluid and filter on schedule.
Balance shaft gear wears and the check engine light comes on
- What you'll notice
- Check engine light with camshaft and crankshaft position correlation codes, sometimes rough running. The engine may run fine at first.
- Why it happens
- Early versions of the 3.5L V6 used a balance shaft (or idler) gear made of a soft metal that wears down, letting the cam timing drift. Mercedes later changed the part.
- What to do
- Have the codes read and the build number checked by a Mercedes specialist. Fixing it means taking apart the front of the engine, so get a firm quote; ignoring it can lead to poor running and engine damage.
Crankshaft pulley (harmonic balancer) separates
- What you'll notice
- A wobble or chirp from the front of the engine, a thrown drive belt, then loss of charging, power steering or cooling.
- Why it happens
- The rubber layer in the crankshaft pulley breaks down with age, letting the outer ring slip or come apart.
- What to do
- Have the pulley checked at every service. Replace it at the first sign of wobble or cracking, before the belt comes off.
Power steering cooler hose can come loose (recall)
- What you'll notice
- Power steering fluid leaking or spraying in the engine bay, a whining pump, or suddenly heavy steering.
- Why it happens
- The clamp on the power steering fluid cooler hose may not grip tightly enough, so the hose can work off.
- What to do
- Have the recall checked with your VIN. If steering gets heavy, slow down and have it towed.
Free at a dealer when the recall is open for your VIN.
Cruise control may not switch off when braking (recall)
- What you'll notice
- Cruise control stays engaged after you tap the brake, particularly if you pump the pedal.
- Why it happens
- Under certain conditions, especially when the brake pedal needs unusually high force, the cruise control might not disengage.
- What to do
- Don't use cruise control until a dealer confirms the recall is done. Turn it off with the switch, and brake firmly.
Free at a dealer when the recall is open for your VIN.
Power steering rack leaks and steering gets heavy
- What you'll notice
- Puddles of power steering fluid, a whining pump, or steering that gets heavy, especially at moderate speeds.
- Why it happens
- The steering rack's seals leak, and the system loses fluid and assist.
- What to do
- Check the fluid level and look for leaks. A leaking rack is usually replaced; don't keep topping it up for long.
Brake booster can corrode and fail (recall)
- What you'll notice
- A hard or inconsistent brake pedal, longer stopping distances, or in rare cases little braking at all.
- Why it happens
- Water can collect under a rubber sleeve on the brake booster and rust through its housing.
- What to do
- This was a do-not-drive recall. Check your VIN right away and have it towed to a dealer if the recall is open.
Free at a dealer when the recall is open for your VIN.
Driver airbag inflator can rupture (recall)
- What you'll notice
- No warning. In a crash the inflator can break apart and throw metal pieces.
- Why it happens
- The driver's airbag inflator can build too much pressure when it deploys and rupture.
- What to do
- Ask the dealer to confirm the recall applies to your VIN and get the free airbag replacement right away.
Free at a dealer when the recall is open for your VIN.
Fuel filter can leak (recall)
- What you'll notice
- A fuel smell or drips near the fuel filter.
- Why it happens
- On some 2011 models, a fuel filter O-ring wasn't lubricated during assembly, and on diesels the filter could leak around its heater. Either can let fuel escape.
- What to do
- Have a dealer check the recalls on your VIN. Don't ignore a fuel smell.
Free at a dealer when the recall is open for your VIN.
Water damages the fuel pump control unit and the engine stalls (recall)
- What you'll notice
- The engine stalls while driving or is hard to start, and you may find water or corrosion in the spare tire well.
- Why it happens
- Water can pool in the spare tire well, where the fuel pump control unit sits, and short it out.
- What to do
- Check your VIN for recall 22V-955. Look in the spare tire well for water, and have the drains and seals checked.
Free at a dealer when the recall is open for your VIN.
Engine can shut off when stopping (recall)
- What you'll notice
- The engine shuts down while braking to a stop or pulling away after an automatic stop-start, which can feel like a normal ECO stop.
- Why it happens
- A software conflict between the engine and transmission computers on AMG GLE43 and GLE450 models.
- What to do
- Have the free software update done. If the engine stalls, keep firm pressure on the brake and restart.
Free at a dealer when the recall is open for your VIN.
Front roof panel may not be bonded after a sunroof repair (recall)
- What you'll notice
- Wind noise or a loose-feeling panel at the front of the roof.
- Why it happens
- On panoramic-roof models that had the front roof panel repaired, the panel may not have been bonded correctly and could come off.
- What to do
- Have a dealer check your VIN, especially if the roof or sunroof was ever repaired.
Free at a dealer when the recall is open for your VIN.
48-volt ground connection under the passenger seat can overheat (recall)
- What you'll notice
- A burning smell from under the front passenger seat or 48-volt system warnings.
- Why it happens
- A ground cable bolt for the mild-hybrid 48-volt system may not be tight, causing heat and a fire risk.
- What to do
- Check your VIN for recalls 22V-231 and 24V-207. The fix is a quick inspection and retightening.
Free at a dealer when the recall is open for your VIN.
Transmission may not downshift and the engine stalls (recall)
- What you'll notice
- The engine stalls as you slow down, or downshifts feel rough.
- Why it happens
- The 9-speed automatic may not fully downshift in certain situations, which can stall the GLE450's engine.
- What to do
- Get the free transmission software update. If the engine stalls, steering and brakes get heavier, so steer to safety and restart.
Free at a dealer when the recall is open for your VIN.
Rear driveshaft locking ring may not be connected (recall)
- What you'll notice
- Loss of power to the wheels or the engine stalling.
- Why it happens
- A locking ring between the transfer case and the rear driveshaft may not have been connected correctly.
- What to do
- Have the recall checked with your VIN.
Free at a dealer when the recall is open for your VIN.
Steering coupling screw can loosen (recall)
- What you'll notice
- A clunk or looseness in the steering, or steering that doesn't respond normally.
- Why it happens
- The locking screw on the steering coupling may loosen and could detach from the steering gear.
- What to do
- Have the free recall repair done promptly. Stop driving if the steering feels loose.
Free at a dealer when the recall is open for your VIN.
Fuel pump can shut down and cut power (recall)
- What you'll notice
- The engine loses power or stalls while driving.
- Why it happens
- The fuel pump may shut down unexpectedly.
- What to do
- Check your VIN for recalls 23V-445 and 23V-880 and have the free fix done.
Free at a dealer when the recall is open for your VIN.
Front airbag sensor wiring may be routed wrong (recall)
- What you'll notice
- An airbag warning light, or no sign at all.
- Why it happens
- Wiring to a front acceleration sensor may be misrouted, which could keep the front airbags from deploying correctly.
- What to do
- Have a dealer inspect and reroute the wiring for free.
Free at a dealer when the recall is open for your VIN.
High-pressure fuel pump may leak fuel and oil (recall)
- What you'll notice
- A fuel or oil smell, or drips under the engine.
- Why it happens
- The wrong screws may have been used on the high-pressure fuel pump, so it doesn't seal against the oil pump and can leak near hot engine parts.
- What to do
- Stop driving if you smell fuel and have the recall done right away.
Free at a dealer when the recall is open for your VIN.
Accelerator pedal bracket can break (recall)
- What you'll notice
- The gas pedal feels loose or stops working normally.
- Why it happens
- The bracket that holds the accelerator pedal module may be poorly welded and can break or detach.
- What to do
- Have a dealer check your VIN and replace the pedal assembly for free.
Free at a dealer when the recall is open for your VIN.
Transmission fluid leaks from the wiring connector
- What you'll notice
- Reddish fluid dripping near the side of the transmission, oil wicking up the wiring harness, or erratic shifting and warning lights.
- Why it happens
- The plug where the wiring enters the transmission is sealed with O-rings that harden and leak. Fluid can travel up the harness toward the control units.
- What to do
- Have the connector and harness inspected. Updated connector seals are inexpensive; do it before fluid reaches the electronics.
Airmatic air suspension sags and the compressor wears out
- What you'll notice
- One corner or the whole SUV sits low after parking, a harsh or bouncy ride, the compressor running after shut-off, or an air suspension warning.
- Why it happens
- On SUVs with Airmatic, the rubber air springs crack and leak with age. The compressor then runs much longer than designed and burns out.
- What to do
- Have the system leak-tested. Replace a leaking strut early to save the compressor. Don't drive far if the SUV is sitting on its bump stops.
Camshaft adjuster solenoids fail or leak oil
- What you'll notice
- Check engine light, rough idle, weak acceleration, worse fuel economy, and sometimes oil seeping into the wiring connector.
- Why it happens
- The magnets that control variable valve timing at the front of the engine wear out and can leak oil into their electrical plugs.
- What to do
- Have the codes read and the solenoids inspected for oil. Replace leaking solenoids, and check the wiring harness for oil before it reaches the engine computer.
Diesel oil cooler seals leak into the engine valley
- What you'll notice
- A low oil warning, oil around the bell housing, or an oil-soaked belly pan and a burning smell.
- Why it happens
- On the 3.0L diesel, the oil cooler sits in the V of the engine. Its gaskets harden with heat and oil runs down the back of the engine.
- What to do
- Have the leak traced. The fix is labor-heavy because the intake must come off, so ask for related seals to be replaced at the same time.
Diesel emissions settlement repair and extended warranty
- What you'll notice
- Usually no symptoms. Your SUV may still need its emissions fix, or you may be eligible for extended warranty coverage.
- Why it happens
- BlueTEC diesels were sold with software that let emissions controls work less well on the road than in testing. A settlement requires a software update and sometimes new parts.
- What to do
- Ask a Mercedes dealer to check your VIN for the emissions modification. Getting it done keeps the extended warranty on the affected parts.
Done free by a Mercedes dealer under the emissions settlement.
Engine stalls when hot from a failing crankshaft sensor
- What you'll notice
- The engine cuts out when warm and won't restart until it cools down, or it cranks without starting.
- Why it happens
- The crankshaft position sensor tells the computer when to fire the spark plugs. When it fails with heat, the engine shuts off.
- What to do
- Have it tested when the problem happens. A new sensor is an inexpensive fix.
Catalytic converters break apart and rattle
- What you'll notice
- A rattle from under the SUV, especially at idle or startup, or a check engine light for catalyst efficiency.
- Why it happens
- The inside of the catalytic converters can crack and break loose with age and heat.
- What to do
- Have the exhaust inspected. A rattling converter usually needs replacement, which is more work on this SUV because suspension parts may need to come off.
Rattle from the engine for a few seconds on a cold start
- What you'll notice
- A rattle or chain noise from the front of the engine for a few seconds after a cold start, sometimes with timing fault codes later.
- Why it happens
- The timing chain tensioner and the plastic balance shaft sprocket on early versions of the 3.5L V6 can wear early, especially with long oil change intervals.
- What to do
- Have a Mercedes specialist check the timing chain and tensioner. Keep up with oil changes using approved synthetic oil.
Active Curve System oil can foam and leak (recall)
- What you'll notice
- Oil leaking from the suspension reservoir cap area under the hood.
- Why it happens
- On SUVs with the Active Curve System (active anti-roll bars), low reservoir oil can foam under some driving conditions and push out of the vent holes.
- What to do
- Have a dealer check your VIN and inspect the reservoir. The repair is free under the recall.
Free at a dealer when the recall is open for your VIN.
Oil can leak from the timing chain tensioner (recall)
- What you'll notice
- Oil drips or seepage near the front of the engine.
- Why it happens
- The gasket around the chain tensioner on the 2.1L diesel may not seal properly.
- What to do
- Have the recall done at a dealer.
Free at a dealer when the recall is open for your VIN.
Emergency call (eCall) system may fail or send the wrong location (recall)
- What you'll notice
- An SOS system warning, or no apparent symptom until the system is needed.
- Why it happens
- Software and SIM card problems in the communication module can stop the automatic crash call from working or make it report the wrong position.
- What to do
- Have a dealer check your VIN for open eCall software recalls; the update is free.
Free at a dealer when the recall is open for your VIN.
Rear middle seat belt buckle can slip under the cushion (recall)
- What you'll notice
- The center rear buckle disappears into the gap below the seat and can't be latched.
- Why it happens
- The buckle can be pushed into the gap under the seat cushion.
- What to do
- Don't seat anyone in the middle until a dealer fixes it for free.
Free at a dealer when the recall is open for your VIN.
Windshield camera and mirror can come loose (recall)
- What you'll notice
- The rearview mirror or the camera housing at the top of the windshield is loose or falls off, and driver-assist features may stop working.
- Why it happens
- The mount for the multi-purpose camera and mirror may not be bonded firmly to the windshield.
- What to do
- Have a dealer check your VIN and reattach the parts for free.
Free at a dealer when the recall is open for your VIN.
Door lock actuators fail and lock buttons jump
- What you'll notice
- Doors that won't lock or unlock with the remote, lock buttons moving up and down by themselves, or a door that won't open.
- Why it happens
- The lock actuator inside the door latch wears out.
- What to do
- Replace the latch assembly in the affected door.
Brake light warning from melted tail lamp sockets
- What you'll notice
- A brake light bulb warning that keeps coming back even after new bulbs, or a brake light that works only some of the time.
- Why it happens
- Heat from the bulb melts the socket in the tail lamp housing, causing a poor connection. Bad grounds cause the same message.
- What to do
- Check the socket for melting or burning. Replacing the tail lamp housing or socket usually solves it.
Repair prices for your Mercedes-Benz M-Class / GLE
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace transmission conductor plate (control unit) and program it
- Replace transmission connector plug adapter and O-rings, top up fluid
- Replace one Airmatic air strut
- Replace balance shaft and timing components
- Replace camshaft adjuster solenoid(s)
- Remove intake and replace oil cooler seals (and cooler if needed)
- Replace crankshaft pulley (harmonic balancer)
- Replace crankshaft position sensor
- Replace catalytic converter
- Replace door latch and lock actuator (one door)
- Replace tail lamp housing or socket
- Replace power steering rack and align
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Emissions software update and parts under the settlementNo charge if your vehicle is included
- Recall repair at a Mercedes-Benz dealerNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.