Mercedes-Benz SLproblems, repair costs and recalls
Problems reported across 1996–2024. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
35 documented issues across all years, most serious first.
Active Body Control (ABC) suspension leaks and sagging
- What you'll notice
- A corner of the car sinks after it sits for a day or two, an ABC warning appears, the ride turns bouncy or harsh, or you hear a hum from the engine bay at low revs. Red hydraulic fluid may drip under the car.
- Why it happens
- ABC is a high-pressure hydraulic suspension. With age its hoses, seals and struts leak, the gas-filled accumulators lose their charge, the pulsation damper fails, and dirty or low fluid wears the pump.
- What to do
- If the car drops low or shows a red ABC warning, stop and don't drive it. Have a specialist check fluid level and pressure and find the leak. Regular fluid and filter changes help prevent failures.
Electronic brake pump (SBC) wear-out
- What you'll notice
- A brake warning message on the dash, the brake pump buzzing often, or a hard pedal with less braking help. Some owners say the pedal feels soft or sinks.
- Why it happens
- These cars use an electro-hydraulic brake system (Sensotronic Brake Control). Its pump unit is designed for a set number of brake cycles and then needs replacing; some fail early.
- What to do
- Treat any brake warning seriously and get the car checked before driving far. Ask a dealer whether your car is still covered: Mercedes extended coverage on this unit to 25 years with unlimited miles.
Electronic brake system can switch to backup mode (recall)
- What you'll notice
- A brake malfunction warning and a hard pedal that needs much more force to stop the car.
- Why it happens
- A fault in the SBC hydraulic unit or its pump ground wire can make the system fall back to its backup mode, which has much less brake assist. Mercedes recalled the cars (04V-296 and 05V-133).
- What to do
- Check your VIN for open recalls and have the free dealer repair done if it was never completed.
Free at Mercedes-Benz dealers; check your VIN for open recalls.
Balance shaft or idler gear wear on V8 (P0016/P0017)
- What you'll notice
- Check engine light with codes P0016 or P0017, later followed by a timing chain rattle.
- Why it happens
- On some early 5.5L V8 engines, the idler gear in the timing drive was made of a metal that wears too fast. The chain gets slack and the cam timing drifts; in the worst case valves can hit pistons.
- What to do
- Don't ignore these codes. Have the timing checked by a Mercedes specialist, and ask whether your engine serial number has the updated gear.
Corroded cylinder head bolts (SL63 AMG)
- What you'll notice
- Coolant level drops while the oil level rises, white smoke, rough idle and eventually sludgy oil.
- Why it happens
- Head bolts on earlier 6.2L AMG engines can corrode and lose clamping force, letting coolant leak into the cylinders or oil. Mercedes changed the bolts in mid-2010.
- What to do
- Stop driving if coolant is disappearing or the oil looks milky, since this can wreck the engine. Have a cooling system pressure test and oil check done.
Camshaft wear ticking (SL63 AMG)
- What you'll notice
- A ticking noise from the top of the engine on cold starts that slowly gets more persistent.
- Why it happens
- On the 6.2L AMG V8 the camshaft lobes can wear against the harder cam followers.
- What to do
- Have a specialist inspect the camshafts, ideally before buying. Keep up regular oil changes with the correct oil.
Head gasket leak (SL320)
- What you'll notice
- Oil or coolant seeping at the front or rear of the cylinder head, coolant loss, or overheating.
- Why it happens
- The 3.2L six-cylinder engine is known for head gasket leaks.
- What to do
- Watch coolant and oil levels and have a leak check done. Fix it before the engine overheats.
Rusty brake lines over rear subframe
- What you'll notice
- A soft brake pedal, a brake fluid leak or visible corrosion on brake pipes.
- Why it happens
- Brake pipes rust where they pass over the rear subframe and the rubber hoses perish with age.
- What to do
- Have the brake lines inspected at every service. Replacing the rear lines is labor-heavy because the subframe has to come down.
Fuel pump can shut off (recall)
- What you'll notice
- The engine may stop while driving and lose drive power.
- Why it happens
- The fuel pump can shut down. Mercedes recalled many models including the SL (23V-445, expanded by 23V-880).
- What to do
- Check your VIN for an open recall; the dealer replaces the fuel pump for free.
Free at Mercedes-Benz dealers; check your VIN for open recalls.
Starter-alternator wiring can short (recall)
- What you'll notice
- Sudden loss of drive power with no warning, or a burning smell.
- Why it happens
- The starter/alternator wiring harness may not be secured and can rub on the drive shaft, causing a short circuit (23V-676).
- What to do
- Check for an open recall; the dealer secures the harness for free.
Free at Mercedes-Benz dealers; check your VIN for open recalls.
Main fuses can fail (recall)
- What you'll notice
- Sudden loss of drive power, or safety systems and the instrument cluster switching off.
- Why it happens
- Some 80-amp fuses were made incorrectly and can fail; Mercedes replaced the main fuse boxes (24V-115).
- What to do
- Check for an open recall; the dealer replaces the fuse boxes for free.
Free at Mercedes-Benz dealers; check your VIN for open recalls.
Wrong fuse box fitted during earlier recall (recall)
- What you'll notice
- Possible sudden loss of drive power or safety functions, and a higher fire risk.
- Why it happens
- Some cars repaired under the earlier fuse recall received a fuse box not meant for the car (25V-255).
- What to do
- Even if the first fuse recall was done, check your VIN again; the dealer inspects and replaces the fuse boxes for free.
Free at Mercedes-Benz dealers; check your VIN for open recalls.
ABC front sensors can give wrong readings (recall)
- What you'll notice
- An ABC warning message, body lean or an uneven ride height.
- Why it happens
- Solder joints on the front acceleration sensor circuit boards could fail, so the suspension computer gets false readings. Mercedes recalled affected cars (08V-405).
- What to do
- Check for an open recall with your VIN; the dealer replaces the sensors for free.
Free at Mercedes-Benz dealers; check your VIN for open recalls.
Folding hardtop (Vario roof) hydraulic leaks or slow operation
- What you'll notice
- The roof works slowly, stops partway, or won't open; you may see hydraulic fluid on the headliner or in the trunk, wet footwells, rattles or wind noise.
- Why it happens
- The roof's hydraulic rams lose their seals with age, often starting with the front roof latch cylinder. A weak battery or flaps at the rear deck that aren't fully closed can also stop the roof.
- What to do
- Charge or test the battery first, then have a specialist check fluid level and look for leaking rams. Rebuilt rams and seal kits cost much less than new dealer parts.
Intake manifold flap failure
- What you'll notice
- Loss of power, poorer fuel economy, rough idle and a check engine light.
- Why it happens
- Oily carbon from the crankcase ventilation system builds up in the intake manifold, and its plastic flaps and linkages get brittle and break.
- What to do
- Have the codes read. The manifold can be replaced or, in some cases, repaired with a kit.
Ignition coil pack failure (V12)
- What you'll notice
- Misfiring, shaking, loss of power and a flashing check engine light.
- Why it happens
- The V12 uses two large coil packs, each serving six cylinders, and they fail often. The 24 spark plugs also need regular replacement.
- What to do
- Have the misfire codes read. If a coil pack has failed, ask for the updated part and check when the spark plugs were last done.
Engine mounts wearing out quickly (V12)
- What you'll notice
- Clunks when shifting or accelerating and more vibration in the cabin.
- Why it happens
- The twin-turbo V12's high torque wears out its fluid-filled engine mounts, roughly every 40,000 miles. Other R230 engines also wear their mounts, just more slowly.
- What to do
- Have the mounts checked if you notice clunking. On V12 cars the job is big, so get a quote from a specialist first.
Shift lever breaks and leaves car stuck in Park
- What you'll notice
- The gear selector won't move out of Park or feels loose.
- Why it happens
- A plastic part inside the shifter mechanism wears out and breaks.
- What to do
- A shop or skilled owner can fit a stronger metal replacement part. It's worth doing early.
Transmission fluid leaking through electrical plug
- What you'll notice
- Fluid seeping where the wiring plug enters the transmission, then harsh shifts, a stuck gear or no gear selection.
- Why it happens
- The seal on the transmission's electrical connector ages and lets fluid wick up the wiring toward the transmission control unit.
- What to do
- Have the connector seal replaced as soon as you see seepage; it is a cheap fix. Waiting can damage the control unit, which is expensive.
Fuel smell in the cabin (early cars)
- What you'll notice
- A fuel smell inside, especially after idling for 10 minutes or more with the top up.
- Why it happens
- Early cars had fuel tank problems; owners also mention a loose baffle plate inside the tank on 2003-2004 models.
- What to do
- Have the smell checked promptly for leaks, since fuel vapor is a fire risk.
Soft top hydraulic cylinders leaking
- What you'll notice
- Puddles of hydraulic fluid near the rear wheels, drips behind the sun visors, or a top that is slow or won't close.
- Why it happens
- The soft top is moved by about a dozen hydraulic cylinders whose seals leak with age. Low fluid in the reservoir under the spare wheel makes the top reluctant to close.
- What to do
- Check the fluid level first, then find which cylinders leak. Rebuilt or aftermarket cylinders cost far less than dealer parts.
Soft top stops working (roof control module)
- What you'll notice
- The top won't open or close at all, or stops partway.
- Why it happens
- The roof control module under the rear seat can fail, and it can be damaged by a voltage spike during a jump-start. Worn sensors and micro switches also stop the sequence.
- What to do
- Have the roof system scanned before replacing parts. Be careful when jump-starting these cars.
Tappet noise from oil feed tubes (early SL500)
- What you'll notice
- A ticking, "tappety" noise from the top of the engine.
- Why it happens
- Plastic oil supply tubes to the valve lifters on the early 32-valve V8 lose pressure, starving the lifters of oil so they wear.
- What to do
- Have it checked soon. Later metal tubes last longer; worn lifters may need replacing too.
Front ball joints and strut mounts wearing
- What you'll notice
- Creaking or clunking from the front over bumps, vague steering or uneven tire wear.
- Why it happens
- The heavy V8 and V12 cars wear the front lower ball joints and the top strut mounts, and the rubber mounts can crack.
- What to do
- Have the front suspension inspected and replace worn parts in pairs, then get an alignment.
Catalytic converter rattle at idle
- What you'll notice
- A metallic rattle from under the car at idle and possibly a check engine light.
- Why it happens
- The inside of the catalytic converter breaks up with age.
- What to do
- Have a shop confirm the source of the rattle. Replacement is one of the more expensive repairs on these cars.
Rust in wheel arches, lower wings and trunk floor
- What you'll notice
- Bubbling paint at the wheel arches, lower front wings near the bumper, bottom of the hardtop pillars, or water and rust in the trunk floor.
- Why it happens
- Debris collects in these areas and holds moisture; water can also enter the trunk through the high-mounted brake light and old hardtop seals.
- What to do
- Clean out drain areas, check the trunk floor under the mat, and have rust treated early before it spreads.
Camshaft adjuster solenoid failure
- What you'll notice
- Check engine light, sometimes with rough running or oil seeping around the round solenoids on the front of the engine.
- Why it happens
- The electric solenoids that control variable valve timing fail with age and can let oil into their connectors.
- What to do
- Have the codes read. The solenoids are fairly cheap; check the wiring plugs for oil while the job is done.
Catalytic converter failure (4.7L V8)
- What you'll notice
- Check engine light, possibly with a sulfur smell or reduced power.
- Why it happens
- Mercedes issued an extended warranty for the catalytic converters on the 4.7L twin-turbo V8.
- What to do
- Ask a Mercedes dealer whether your car is still covered under the extended catalytic converter warranty before paying for a repair.
Coolant line or hose leak
- What you'll notice
- A coolant warning on the dash, a sweet smell, or coolant under the car. One owner was stranded when a radiator hose came loose.
- Why it happens
- Mercedes issued a service bulletin for coolant warnings caused by a leaking coolant line, and hoses can come loose.
- What to do
- Don't keep driving with a coolant warning. Check the level when the engine is cold and have the leak found.
ABC pulsation damper failure
- What you'll notice
- A humming or droning noise from the engine bay at low revs, or ABC warnings, on cars with Active Body Control.
- Why it happens
- The pulsation damper that smooths pressure from the ABC pump fails and can leak.
- What to do
- Have the ABC system checked by a specialist; a CPO or extended warranty may cover it.
Hands-off-wheel warning may not work with DISTRONIC (recall)
- What you'll notice
- When using adaptive cruise with steering assist, the car may not warn you that your hands are off the wheel.
- Why it happens
- A software error in the steering wheel hand-detection unit (22V-189).
- What to do
- Have the free software update done at a dealer, and keep your hands on the wheel.
Free at Mercedes-Benz dealers; check your VIN for open recalls.
Trunk lid seal leaking water
- What you'll notice
- Water in the trunk after rain or a car wash, sometimes with rust under the seal.
- Why it happens
- The rubber seal along the top of the trunk lets water in after several years.
- What to do
- Clean out any rust and refit the seal with proper sealant; just replacing the rubber may not stop it.
Auxiliary battery failure
- What you'll notice
- A message about the auxiliary battery or start/stop not working.
- Why it happens
- These cars have a small second battery that supports electronics; it wears out after several years.
- What to do
- Have the auxiliary battery tested and replaced; it's a routine job.
Steering column noise or height adjustment jamming
- What you'll notice
- Grinding or creaking from the steering column, or the power column getting stuck at its top or bottom position.
- Why it happens
- Mercedes issued service bulletins for noises in the steering column area and jamming of the height adjustment.
- What to do
- Mention the bulletins to the dealer; they describe the fix.
Corrosion near headlamp mounting bolts
- What you'll notice
- Usually nothing noticeable at first; corrosion may be found on the body near the headlamp housing.
- Why it happens
- Mercedes issued a service bulletin saying certain bolts on the headlamp housing can cause corrosion on the body.
- What to do
- Ask the dealer to check this bulletin; repairs should be covered while the car is under warranty.
Repair prices for your Mercedes-Benz SL
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace leaking ABC strut, accumulators or valve block
- Replace SBC hydraulic brake unit
- Reseal or replace leaking roof hydraulic rams
- Replace timing idler gear, chain and tensioner
- Replace intake manifold assembly
- Replace one V12 coil pack
- Replace V12 engine mounts
- Rebuild shifter with aluminum shift lever repair kit
- Replace and reseal trunk lid rubber seal
- Replace leaking soft top hydraulic cylinders
- Replace roof control module
- Replace cylinder head gasket
- Replace plastic camshaft oil feed tubes
- Replace front lower ball joints and bushings (pair)
- Replace camshaft adjuster solenoid(s)
- Replace auxiliary (backup) battery
- Replace ABC pump pulsation damper
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Free dealer recall repairNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.