Your 2007 Mercury Milanproblems, repair costs and recalls
What we've documented about the 2007 Mercury Milan: problems owners and shops report, typical repair and upkeep costs, and safety recalls.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems for your 2007 Mercury Milan
16 documented issues apply to 2007, most serious first.
Takata passenger airbag inflator (do-not-drive recall)
- What you'll notice
- Usually nothing you can see or feel. The danger only shows up if the passenger airbag deploys in a crash.
- Why it happens
- The passenger airbag inflator uses a propellant that breaks down with years of heat and humidity, so it can burst and throw metal pieces into the cabin. Ford told owners not to drive affected cars until the inflator is replaced, and later recalls also covered some replacement inflators.
- What to do
- Check your VIN for open airbag recalls right away. If one is open, do not drive the car; ask the dealer to arrange the free repair and a tow if needed.
Free at a Ford or Lincoln dealer; ask about towing if the car is under a do-not-drive notice.
Takata driver airbag inflator (recall)
- What you'll notice
- No warning in normal driving. The risk appears only if the driver airbag deploys.
- Why it happens
- The driver airbag inflator can also rupture after long exposure to heat and humidity. Ford recalled 2006-2011 Milans to replace it.
- What to do
- Check your VIN for recall 21V-158 and get the free repair as soon as possible.
Free under recall 21V-158.
ABS valves stick, brake pedal sinks farther
- What you'll notice
- The brake pedal feels soft or sinks lower than normal before the car slows, stopping takes longer, or the brakes grab or lock unexpectedly.
- Why it happens
- Valves inside the ABS hydraulic unit can react with some brake fluid additives and not close fully, so pedal travel grows. Soft brake pedals and grabbing brakes are the top Milan brake complaints, and Ford recalled 2006-2010 cars to flush the system and test or replace the unit.
- What to do
- Have the brakes checked before normal driving. Check your VIN for recall 19V-904 and get the free repair.
Free under recall 19V-904. Owners who paid out of pocket report expensive ABS and brake work.
Driver floor mat can snag the gas pedal
- What you'll notice
- The gas pedal sticks or does not return fully, especially with an all-weather mat in place.
- Why it happens
- The driver all-weather floor mat can slide forward and catch the accelerator pedal. Ford recalled the mats.
- What to do
- Remove any loose or stacked mats now and check your VIN for recall 14E-028. Use only a mat that is secured to the floor hooks.
Harsh shifts or automatic transmission failure
- What you'll notice
- Harsh or jerky shifts, especially 1-2 and 3-4, shifting that gets worse over time, slipping, or the transmission failing completely.
- Why it happens
- Owners of both four-cylinder and V6 cars report internal wear, torque converter debris and valve body faults. The wrong fluid makes it worse.
- What to do
- Check the fluid level and type. If shifting is harsh or slipping, have it diagnosed early; a valve body repair is far cheaper than a rebuild.
AWD power transfer unit leak or burnt fluid
- What you'll notice
- A burning oil smell after driving, drips near the front of the car, or a whine from underneath.
- Why it happens
- The power transfer unit that sends power to the rear wheels runs hot and holds little fluid. Its seals leak and the fluid breaks down, and there is no easy way to check the level.
- What to do
- Have the unit inspected for leaks and the fluid changed. Fixing a seal early costs much less than replacing a failed unit.
Valve cover gasket leaks oil into spark plug wells
- What you'll notice
- A burning oil smell, oil on the top of the engine, or a misfire and check engine light.
- Why it happens
- The valve cover gasket on the 2.3L hardens and leaks, and oil can run down into the spark plug wells and damage the coils.
- What to do
- Have the gasket and plug well seals replaced before oil ruins the ignition coils.
Broken engine or transmission mounts
- What you'll notice
- A thump or clunk when shifting into gear or accelerating, and more vibration at idle.
- Why it happens
- Owners report broken or worn engine and transmission mounts on both the four-cylinder and V6, sometimes letting the engine move noticeably.
- What to do
- Have the mounts inspected and replace any that are cracked or collapsed.
Worn tie rods, ball joints and control arm bushings
- What you'll notice
- Clunks or creaks over bumps and while turning, loose steering, or uneven tire wear.
- Why it happens
- Tie rod ends, ball joints, control arm bushings and sway bar links wear on these cars. RepairPal lists squeaks and creaks over bumps and while turning among common Milan complaints.
- What to do
- Have the front end checked for play and get an alignment after replacing parts.
Wheel bearing grinding or groaning
- What you'll notice
- A hum, groan or grinding noise that grows with speed.
- Why it happens
- Owners report front and rear wheel bearings wearing out, including on hybrid and AWD models.
- What to do
- Have the noisy corner found and the bearing or hub replaced before it gets loose.
Interior door handle breaks
- What you'll notice
- An inside door handle snaps, sticks open, or no longer opens the door.
- Why it happens
- The plastic inside handles and their latch linkage crack. Owners of 2006 through 2010 Milans report broken handles, often on the driver door.
- What to do
- Replace the broken handle. If a door won't open from inside, fix it soon in case you need to get out quickly.
Thermostat sticks open, engine runs cold
- What you'll notice
- The temperature gauge stays low, the heater blows lukewarm, or a check engine light comes on with a thermostat code.
- Why it happens
- The thermostat on the 2.3L four-cylinder sticks open, so the engine never fully warms up. Owners report replacing it, sometimes along with the housing.
- What to do
- Have the thermostat replaced. Running cold hurts fuel economy and heater output and keeps the check engine light on.
Check engine light from secondary air injection valve
- What you'll notice
- A check engine light with secondary air system codes; the car usually drives normally.
- Why it happens
- The secondary air injection system pumps air into the exhaust on cold starts to cut emissions. Its control or check valve fails on the 2.3L four-cylinder.
- What to do
- Have the codes read. Replace the failed valve so the car can pass an emissions test.
Serpentine belt tensioner or pulley wears
- What you'll notice
- A squeal or chirp from the front of the engine, especially on cold starts, or a belt that slips or comes off.
- Why it happens
- The drive belt tensioner and idler pulleys wear out; owners of several years report replacing the belt and tensioner.
- What to do
- Replace a worn tensioner along with the belt. A belt that comes off can stop the alternator and water pump.
Blower motor or resistor fails
- What you'll notice
- The fan only works on some speeds, stops working, chirps or clicks, or there is a burning smell from the dash.
- Why it happens
- Owners report failed blower motors, blower resistors and blower wiring connectors.
- What to do
- Have the blower circuit checked. If there is a burning smell, have the connector inspected too, since a melted connector will ruin a new motor.
Rear brake calipers stick
- What you'll notice
- The car pulls or drags, a hot or burning smell from a rear wheel, or rear pads that wear out unevenly.
- Why it happens
- Owners report rear calipers seizing, sometimes right after a pad and rotor job.
- What to do
- Have the calipers and slide pins checked. A stuck caliper wears pads fast and can overheat the brakes.
Repair prices for your 2007 Mercury Milan
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace automatic transmission with remanufactured unit
- Replace power transfer unit seals and fluid
- Replace interior door handle
- Replace thermostat and housing
- Replace valve cover gasket and plug well seals
- Replace secondary air injection valve
- Replace engine or transmission mount (one)
- Replace belt tensioner and drive belt
- Replace blower motor resistor or motor
- Replace front lower control arm or tie rod ends (one side) and align
- Replace wheel hub bearing (one)
- Replace rear brake caliper (one)
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Replace passenger airbag inflatorNo charge if your vehicle is included
- Replace driver airbag inflatorNo charge if your vehicle is included
- Flush brake system, test and replace ABS unit if neededNo charge if your vehicle is included
- Replace driver floor matNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Checking the NHTSA recall database…