Nissan 350Z / 370Z / Zproblems, repair costs and recalls
Problems reported across 2003–2024. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
30 documented issues across all years, most serious first.
Clutch pedal sticks to the floor
- What you'll notice
- After hard or hot driving the clutch pedal goes soft, stays down on the floor, and you cannot shift gears. Once the car cools the pedal often comes back.
- Why it happens
- From 2007 Nissan used a clutch slave cylinder that sits inside the bell housing. Owners and a class action lawsuit say heat from the transmission can boil the clutch fluid, creating air in the system so the pedal loses pressure. Manual 370Zs were the subject of lawsuits over the same symptom.
- What to do
- If the pedal sticks, pull over safely and let the car cool. Have the clutch fluid bled and the slave cylinder checked. Many owners fit an updated slave cylinder or an external slave conversion when the clutch is replaced.
Manual gearbox grinds going into gear
- What you'll notice
- Grinding or crunching when shifting, most often into 3rd, 5th or 6th, or from 1st to 2nd on a cold gearbox. Some cars pop out of gear under load.
- Why it happens
- The synchronizer rings inside the 6-speed manual wear out, especially with hard driving. Owners of both the 350Z and 370Z report synchro wear and gearbox replacements.
- What to do
- Try fresh gear oil of the correct type first, which can help a little. If grinding continues, have a transmission shop inspect the synchros before more gears are damaged.
Excessive oil consumption on 2005-2006 manual cars
- What you'll notice
- The oil level drops quickly between changes, the low oil light may come on, and some engines make an unusual noise.
- Why it happens
- The higher-revving engine used in 2005 Track and anniversary models and 2006 manual cars can burn oil. Nissan published a bulletin with an oil consumption test and replaced the short block on engines that failed it.
- What to do
- Check the dipstick every fill-up and top up as needed. Running low can damage the timing chain and bearings. Ask a Nissan dealer to perform the oil consumption test.
Oil gallery gasket failure
- What you'll notice
- Check engine light with codes P0011 or P0021, a sudden drop in oil pressure, limp mode, or oil seeping near the back of the engine.
- Why it happens
- Small gaskets that seal oil passages behind the timing cover can harden and leak, so the variable valve timing loses oil pressure. Nissan revised the gasket design around 2012.
- What to do
- Do not keep driving if the oil pressure light comes on. Have a shop confirm the codes and replace the gaskets with the updated design. Changing them before they fail is cheaper than an engine.
Crank or cam sensor can stall the engine (recall)
- What you'll notice
- The service engine soon light comes on, the engine loses power, stalls while driving, or will not start.
- Why it happens
- A faulty weld in the crankshaft or camshaft position sensors on early cars could make them fail.
- What to do
- Confirm the recall was done. If it was and the engine still stalls, have the sensors tested again.
Fuel filler hose can crack and leak (recall)
- What you'll notice
- A gasoline smell near the rear of the car or fuel dripping after you fill up.
- Why it happens
- The rubber hose between the filler neck and the tank can crack and leak fuel, creating a fire risk.
- What to do
- If you smell fuel, do not park in a closed garage and get it checked. Confirm the free recall hose replacement was done.
Passenger airbag may be switched off by mistake (recall)
- What you'll notice
- The passenger airbag off light may stay lit even with an adult in the seat.
- Why it happens
- A part in the passenger seat occupant sensor could be out of spec and interrupt its signal, so the system turns the passenger airbag off.
- What to do
- Confirm the recall was done. The dealer tests the system and replaces the sensor if needed at no cost.
Driver curtain airbag may be installed wrong (recall)
- What you'll notice
- No visible signs. The airbag may not deploy correctly in a side crash.
- Why it happens
- A small number of 2018 370Zs may have had the driver-side curtain airbag installed incorrectly at the factory.
- What to do
- Check your VIN for the open recall. The dealer inspects and corrects the airbag for free.
Car may roll away in Park (recall)
- What you'll notice
- The car could roll even with the 9-speed automatic shifter in Park.
- Why it happens
- The parking pawl inside the automatic may not fully engage because of extra resistance in the park mechanism.
- What to do
- Always set the parking brake until the free transmission computer update is done.
Camshaft position sensor failure
- What you'll notice
- Stalling, hard starting, a rough idle or a check engine light, often when the engine is warm.
- Why it happens
- Camshaft position sensors keep failing on these engines even outside the 2003 recall. They are among the most reported repairs in owner surveys.
- What to do
- Have the codes read. Replacing the camshaft sensors (and the crank sensor if it is also flagged) is usually a quick job.
Timing chain rattle on cold start
- What you'll notice
- A rattle or whine from the front of the engine for a few seconds after a cold start, sometimes with a check engine light.
- Why it happens
- The timing chain guides and tensioner wear with age and mileage, and low or old oil speeds this up, letting the chain slap.
- What to do
- Keep the oil topped up and changed on time. If the rattle lasts longer or gets louder, have the chain guides inspected before the chain jumps a tooth.
Power window stops working or won't close fully
- What you'll notice
- A window that moves slowly, stops partway, will not go up, or loses its auto up and down. These frameless windows also drop slightly when the door opens, so a failing window can stop the door from closing properly.
- Why it happens
- Window motors and regulators are the most reported repair in TrueDelta's owner survey for this car. The windows can also lose their settings after the battery is disconnected and need re-learning.
- What to do
- Try the window reset procedure in the owner's manual first. If it still fails, have the motor and regulator checked. Keep the car covered if a window will not close.
Worn front compression rod bushings
- What you'll notice
- Clunking over bumps, a shimmy or vibration under braking, vague steering, or uneven front tire wear.
- Why it happens
- The large rubber bushings on the front compression rods wear out and crack over time. Left too long, the whole arm may need replacing.
- What to do
- Have the front suspension inspected. Replacing the bushings early, often with firmer aftermarket ones, is cheaper than replacing arms.
Tires wear out quickly on the inner edges
- What you'll notice
- Tires, especially the rear or front inside edges, wear down far faster than expected, sometimes needing replacement in under a year.
- Why it happens
- The factory alignment settings and worn suspension parts on these cars put a lot of camber on the tires, which wears the inside edges. Tire wear is one of the biggest complaint areas for early 350Zs.
- What to do
- Check tire edges regularly. A careful alignment closer to zero toe, plus replacing worn bushings, helps tires last much longer.
Steering lock fails and the car won't start
- What you'll notice
- The push-button start does nothing or shows a steering lock warning, and the steering wheel stays locked. The car cannot be driven.
- Why it happens
- Oil can get inside the electronic steering column lock unit, so the body computer will not allow the engine to start. Nissan ran a free service campaign to replace the unit on many 2009-2010 370Zs.
- What to do
- Ask a Nissan dealer whether campaign P3208 applies to your car. If not, the lock unit can be replaced, and some shops offer cheaper repair options.
Power window may not reverse when it hits something (recall)
- What you'll notice
- The auto-up window keeps pushing when it meets an obstruction instead of backing down, which can pinch fingers.
- Why it happens
- A programming error in some window switches required too much force before the auto-reverse kicked in.
- What to do
- Use care with the auto-up window and get the free switch replacement done.
Clogged or rattling catalytic converters
- What you'll notice
- A rattle from under the car, misfires, a check engine light, rough idle or a loss of power.
- Why it happens
- If the engine runs hot or misfires, the honeycomb inside the converters can melt or break apart, which blocks the exhaust. It has been seen from about 75,000 miles.
- What to do
- Fix any misfire right away to protect the converters. If a converter is rattling or clogged, have the exhaust back-pressure tested before replacing parts.
Water pump leaks or fails
- What you'll notice
- Coolant leaking from the front of the engine, a whining noise, or the temperature gauge climbing.
- Why it happens
- The water pump wears out with mileage, usually around 100,000 miles.
- What to do
- If the engine starts to overheat, stop and let it cool. Replace the pump at the first sign of a leak, and consider the thermostat at the same time.
Soft clutch pedal from a leaking master cylinder
- What you'll notice
- The clutch pedal feels soft or spongy, sinks, or the clutch does not fully release, making shifts hard.
- Why it happens
- The clutch master cylinder and slave cylinder seals can leak internally. Owner surveys list both cylinders among the top repairs for these cars.
- What to do
- Check the clutch fluid level (it shares the brake reservoir on many cars). Have the hydraulic parts inspected and the fluid bled.
A/C compressor or condenser failure
- What you'll notice
- The A/C blows warm air or makes noise when it switches on.
- Why it happens
- Owners report failed A/C compressors and condensers on these cars. The condenser sits low in the front and can be damaged by road debris.
- What to do
- Have the system checked for leaks and pressure. If the compressor failed, the system should be flushed when the new one goes in.
Rear differential whine or clunk
- What you'll notice
- A whine when you lift off the throttle, or a clunk from the rear when getting on and off the gas.
- Why it happens
- The ring and pinion gears in the differential can wear, and the differential mount bushings soften over time.
- What to do
- Change the differential fluid and check its color. Dark fluid or a loud whine means the differential should be inspected.
Pop-up hood may not lift in a crash (recall)
- What you'll notice
- No visible signs. The hood may not raise to cushion a pedestrian in a frontal crash.
- Why it happens
- Fasteners on the left front bumper reinforcement clip can loosen and keep the pop-up hood system from working.
- What to do
- Check your VIN for open recalls. The dealer tightens the fasteners for free.
Pedestrian sensor wiring may be reversed (recall)
- What you'll notice
- Usually none, though a warning for the pop-up hood system may appear. The hood may not lift in a pedestrian crash.
- Why it happens
- Connectors for the right-side pedestrian sensors may have been swapped in the front bumper wiring harness.
- What to do
- Get the free bumper harness replacement done. Check your VIN for open recalls.
Notchy shifting or grinding in the 6-speed manual
- What you'll notice
- Shifts feel notchy, especially 1st to 2nd, and some cars grind going into gear.
- Why it happens
- The cause is not confirmed. Owners suspect the stronger gearbox parts needed for the twin-turbo engine. Nissan also issued dealer actions on early cars to inspect a 5th-gear shift lever plate.
- What to do
- Let the car warm up before shifting hard, and report grinding to a Nissan dealer while the car is under warranty.
These cars are young enough that most repairs fall under Nissan's powertrain warranty.
Ticking or knocking at idle from the fuel line
- What you'll notice
- A ticking or knocking sound you can hear in the cabin when the engine idles.
- Why it happens
- Pressure pulses in the fuel line cause the noise. Nissan released a revised fuel damper and hose to quiet it.
- What to do
- This is not harmful, but a dealer or shop can install the revised damper if the noise bothers you.
Clicking from the rear axles when pulling away
- What you'll notice
- A click or clunk from one or both rear wheels when you accelerate from a stop.
- Why it happens
- Nissan traced it to the joint between the rear driveshaft and the wheel hub. Its bulletin calls for cleaning the flange surface and adding a special grease.
- What to do
- Ask a dealer or shop to perform the bulletin repair. If clicking continues, have the outer CV joints checked for wear.
Rear hatch won't pop up or stay open
- What you'll notice
- The hatch unlatches but does not lift, or slowly drops back down when opened.
- Why it happens
- The gas struts that hold the hatch up lose pressure with age. This is the most common 370Z problem on RepairPal.
- What to do
- Replace both hatch struts. It is an easy job, and a falling hatch can hurt someone.
Convertible top tears or top motor fails
- What you'll notice
- The soft top on Roadster models tears or wears through, leaks, or the power top stops moving.
- Why it happens
- Owners report worn and torn fabric tops and failed top motors on Roadsters as they age.
- What to do
- Keep the top clean and treated. Have a leaking or stuck top looked at by a convertible top specialist rather than forcing it.
Check engine light with mass airflow codes
- What you'll notice
- The check engine light comes on with codes P0101 or P010B. The car may drive normally.
- Why it happens
- Nissan issued a bulletin for these mass airflow sensor circuit codes on the 2023 Z.
- What to do
- Have the codes read and ask a Nissan dealer about the related bulletin. It is often covered by the new car warranty.
Key not detected and engine won't start
- What you'll notice
- A key not detected message appears and the push-button start will not start the engine.
- Why it happens
- Nissan's bulletin covers the intelligent key not being recognized. A weak key fob battery or interference can also cause it.
- What to do
- Hold the key fob against the start button and press it; this usually starts the car. Replace the fob battery, and ask the dealer about the bulletin if it keeps happening.
Repair prices for your Nissan 350Z / 370Z / Z
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace concentric clutch slave cylinder (transmission removal) and bleed
- Rebuild or replace 6-speed manual transmission
- Replace short engine block
- Replace oil gallery gaskets behind the timing cover
- Replace camshaft position sensors
- Replace timing chain guides and tensioners
- Install revised fuel damper and hose
- Replace power window motor and regulator
- Replace front compression rods or bushings and align
- Four-wheel alignment and two new tires
- Clean and grease rear driveshaft flange per bulletin
- Replace electronic steering column lock unit
- Replace catalytic converter
- Replace water pump and coolant
- Replace both hatch gas struts
- Replace clutch master cylinder and bleed
- Replace A/C compressor or condenser and recharge
- Replace convertible top fabric or top motor
- Replace differential bushings or rebuild ring and pinion
- Diagnose and repair per Nissan bulletin
- Replace key fob battery or diagnose key system
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Replace crank and cam position sensorsNo charge if your vehicle is included
- Replace fuel filler hoseNo charge if your vehicle is included
- Test and replace occupant sensorNo charge if your vehicle is included
- Replace power window switchNo charge if your vehicle is included
- Inspect and correct curtain airbag installationNo charge if your vehicle is included
- Reprogram transmission computerNo charge if your vehicle is included
- Tighten bumper reinforcement fastenersNo charge if your vehicle is included
- Replace front bumper harnessNo charge if your vehicle is included
- Inspect shifter and transmission under warrantyNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.