Oldsmobile Bravadaproblems, repair costs and recalls
Problems reported across 1996–2004. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
33 documented issues across all years, most serious first.
Transmission slips, drops into neutral or shifts hard
- What you'll notice
- Slipping or flaring revs between gears, the transmission suddenly acting like it is in neutral, harsh shifts from Park into Drive or Reverse (worse when cold), or fluid leaks.
- Why it happens
- The Bravada uses GM's 4L60-E four-speed automatic. Automatic transmission complaints are the most common powertrain problem across these years, and GM issued a bulletin for harsh engagement on later models.
- What to do
- Check the fluid level and condition. If it slips or loses drive, avoid highway driving and have a transmission shop diagnose it before it fails completely.
Intake manifold gaskets leak coolant
- What you'll notice
- Coolant level dropping with no visible leak, a sweet smell, the engine running hot, a low coolant light, or misfires and rough running.
- Why it happens
- The original intake manifold gaskets on the 4.3L Vortec V6 have a plastic core that breaks down with heat cycles, often from about 50,000 miles. Coolant can leak outside or into the engine oil.
- What to do
- Don't keep topping off coolant without finding the leak. Check the oil for a milky look. Have the gaskets replaced with updated metal-core gaskets before the engine overheats.
Cracked cylinder liner on the early 4.2L six
- What you'll notice
- Coolant loss, white exhaust smoke, overheating or a misfire.
- Why it happens
- Some early 4.2L engines developed cracked cylinder liners. GM extended the engine warranty to 7 years or 100,000 miles, which has ended.
- What to do
- If you lose coolant with no outside leak or see white smoke, stop driving and have a cooling system and combustion leak test done.
Driveshaft can puncture the fuel tank in a crash (recall)
- What you'll notice
- No warning sign in normal driving.
- Why it happens
- In some crashes the front driveshaft could contact and rupture the fuel tank, leaking fuel (recall 96V234000).
- What to do
- Check your VIN for open recalls. Any fuel smell or drip needs inspection before driving.
Free at a GM dealer if it was never done. Check your VIN first.
Ball joints can corrode and separate (recall)
- What you'll notice
- Clunking from the front, wandering steering, or uneven tire wear. In the worst case the front suspension can collapse.
- Why it happens
- Corrosion can cause the upper and lower ball joints to fail. GM recalled these trucks (01V200000).
- What to do
- If the front end clunks or steering feels loose, stop driving and have the ball joints inspected. Check your VIN for the recall.
Free at a GM dealer if it was never done. Check your VIN first.
Seat belt buckles may release in a crash (recall)
- What you'll notice
- No warning sign; a buckle may seem to latch normally.
- Why it happens
- Some buckles could malfunction in a severe crash. GM recalled the trucks to replace them.
- What to do
- Check your VIN for open recalls and have the buckles replaced if listed.
Free at a GM dealer if it was never done. Check your VIN first.
Rear brake pipe can crack (recall)
- What you'll notice
- A soft or sinking brake pedal, brake fluid under the rear axle, or sudden loss of rear braking.
- Why it happens
- The brake pipe on the rear axle could fatigue and crack. GM recalled these trucks.
- What to do
- If the pedal feels soft or you see fluid, don't drive it. Check your VIN for the recall.
Free at a GM dealer if it was never done. Check your VIN first.
Lower control arm nuts may be loose (recall)
- What you'll notice
- Clunking from the front, the truck pulling, or a change in steering feel.
- Why it happens
- Some lower control arm nuts on AWD trucks were not tightened enough, and the arm could separate from the frame. GM recalled them.
- What to do
- Stop driving and have the front suspension checked if it clunks or pulls. Confirm the recall with your VIN.
Free at a GM dealer if it was never done. Check your VIN first.
Brake lights and rear hazards can stop working (recall)
- What you'll notice
- Brake lights don't come on, rear hazards don't flash, or a turn signal acts up.
- Why it happens
- The multifunction switch can develop an open circuit. GM recalled the trucks to replace the hazard switch carrier (01V364000 and 08V231000).
- What to do
- Ask someone to check your brake lights. Don't drive without working brake lights; check your VIN for both recalls.
Free at a GM dealer if it was never done. Check your VIN first.
Front lower control arm bracket can crack (recall)
- What you'll notice
- Clunking, wandering or pulling, or the front end sitting crooked.
- Why it happens
- The front lower control arm brackets could fracture and separate from the frame. GM replaced them under recall 01V126000. Owners have also reported corroded rear suspension brackets.
- What to do
- Stop driving if the front end clunks or pulls. Check your VIN for the recall.
Free at a GM dealer if it was never done. Check your VIN first.
Fuel filter line can come apart (recall)
- What you'll notice
- The engine stalls or won't start, a fuel smell, or fuel dripping under the truck.
- Why it happens
- The fuel filter fitting could disconnect, causing a stall, loss of power steering assist and a fire risk. Recall 02V121000 replaced the retainers.
- What to do
- If you smell fuel or see drips, don't start it. Check your VIN for the recall.
Free at a GM dealer if it was never done. Check your VIN first.
Driver airbag inflator can crack (recall)
- What you'll notice
- No warning sign.
- Why it happens
- The driver airbag inflator could fracture at a weld when it deploys, sending fragments toward occupants. Recall 02V222000 replaced affected modules.
- What to do
- Check your VIN for this recall and get it done if open.
Free at a GM dealer if it was never done. Check your VIN first.
Air suspension can stall the engine (recall)
- What you'll notice
- The engine stalls or won't restart on trucks with rear air suspension.
- Why it happens
- A power spike from the air suspension compressor can damage the engine computer. Recall 04V289000 added a wiring harness.
- What to do
- Check your VIN for the recall, especially if your Bravada has rear air suspension.
Free at a GM dealer if it was never done. Check your VIN first.
Front seat belts may not lock (recall)
- What you'll notice
- No obvious sign; the belt may not lock up in a crash.
- Why it happens
- One of two sensors in the front belt retractors could be inoperative. Recall 04V201000 replaced faulty retractors.
- What to do
- Check your VIN for the recall.
Free at a GM dealer if it was never done. Check your VIN first.
Left front brake pipe can crack (recall)
- What you'll notice
- A longer pedal travel, a soft pedal or brake fluid near the left front wheel.
- Why it happens
- A manufacturing score on the left front brake pipe could cause it to crack. Recall 03V151000 replaced the pipe.
- What to do
- Don't drive if the pedal is soft or fluid is leaking. Check your VIN for the recall.
Free at a GM dealer if it was never done. Check your VIN first.
Spider fuel injector leaks or misfires
- What you'll notice
- Long cranking before it starts, rough idle and stumbling at low speed that smooths out at higher rpm, a fuel smell, and misfire codes.
- Why it happens
- The 4.3L uses a central "spider" injector assembly that can leak at its pressure regulator and lines, flooding cylinders with fuel.
- What to do
- Have fuel pressure tested and the misfire codes checked. Replace the injector assembly if it is leaking; a fuel leak under the intake is also a fire risk.
Misfire from a worn distributor cap and rotor
- What you'll notice
- The check engine light with misfire codes (P0300 to P0306), shaking at idle, weak acceleration, or slow starts.
- Why it happens
- The plastic distributor cap on the 4.3L sits in a hot spot and warps, wearing the rotor and its bushing.
- What to do
- A new cap and rotor are inexpensive and often the first thing to check for misfires on this engine.
Rough idle or stalling from the idle control valve or throttle sensor
- What you'll notice
- Rough or surging idle, stalling at stops, hesitation, or code P0122.
- Why it happens
- The idle air control valve clogs with deposits and the throttle position sensor wears out on the 4.3L.
- What to do
- Have the throttle body cleaned and the sensors tested. Stalling in traffic is a safety risk, so don't put it off.
AWD shudder or clunk in tight turns
- What you'll notice
- A shudder, binding or clunk when turning sharply at low speed on dry pavement, or AWD warning lights.
- Why it happens
- The full-time AWD transfer case can shudder. GM issued bulletins for transfer case shudder and low-speed turning vibration, and NHTSA complaints mention the transfer case.
- What to do
- Make sure all four tires are the same size and evenly worn. Have the transfer case fluid changed and the unit checked.
Cooling fan roars or engine runs hot
- What you'll notice
- The engine fan roars constantly, or the temperature climbs in traffic. The transmission may shift late.
- Why it happens
- The 4.2L six uses an electronically controlled fan clutch that commonly fails. On 2002 models, GM also reprogrammed the engine computer for excessive fan noise and late shifts.
- What to do
- If the gauge climbs, pull over and let it cool. Have the fan clutch tested and ask about software updates.
Ignition switch failure: gauges die and transmission sticks in third
- What you'll notice
- The instrument panel goes dead while driving and the transmission stays in third gear.
- Why it happens
- A failing ignition switch can cut power to the cluster and transmission controls.
- What to do
- Have the ignition switch tested. Losing gauges while driving is unsafe, so fix it promptly.
Rear sits low from a failed air suspension compressor
- What you'll notice
- The rear end sags, especially with a load, the compressor runs a long time or not at all, or a service suspension message appears.
- Why it happens
- Bravadas with the rear load-leveling air suspension (standard on 2WD, optional on AWD) often lose air from worn air springs or a failed compressor. RepairPal lists it as the most common Bravada problem.
- What to do
- A sagging rear can upset headlight aim and handling. Have the air springs and compressor tested; some owners convert to regular coil springs.
Fuel vapor smell from a cracked tank inlet valve
- What you'll notice
- A gasoline smell around the rear of the truck, especially after filling up.
- Why it happens
- The check valve where the filler pipe enters the fuel tank can crack, letting vapor and droplets escape. GM offered special coverage for this.
- What to do
- Have the tank inlet checked if you smell fuel. Ask a GM dealer whether any special coverage still applies.
AWD lights flash and AWD stops working
- What you'll notice
- The 4WD or AWD indicator flashes and the system stops sending power to the front, with codes like C0327.
- Why it happens
- GM issued bulletins for the 4WD/AWD lamps flashing and the system becoming inoperative, often traced to the transfer case encoder or wiring.
- What to do
- Have the codes read. Drive carefully on slippery roads until it is repaired.
Wipers work on and off (recall)
- What you'll notice
- The windshield wipers stop, work only sometimes, or quit in bad weather.
- Why it happens
- Cracked solder joints in the wiper circuit and a failure-prone wiper motor led to recalls, including 03V159000.
- What to do
- Don't drive in rain or snow if the wipers act up. Check your VIN for open recalls.
Free at a GM dealer if it was never done. Check your VIN first.
Instrument cluster may not power up (recall)
- What you'll notice
- Gauges and warning lights don't come on when you start the truck.
- Why it happens
- Some clusters didn't fully power up at startup. Dealers reprogrammed them under recall 03V096000.
- What to do
- Check your VIN for the recall. Don't drive without working gauges.
Free at a GM dealer if it was never done. Check your VIN first.
Wipers stop or washer keeps running (recall)
- What you'll notice
- Wipers won't start, stop mid-use, or the washer pump keeps running.
- Why it happens
- Water can enter the wiper module and short it. Recall 04V046000 sealed and repaired the module.
- What to do
- Don't drive in bad weather without working wipers. Check your VIN for the recall.
Free at a GM dealer if it was never done. Check your VIN first.
Brake light bulbs flicker and fail (recall)
- What you'll notice
- Brake lights or rear turn signals flicker or stop working.
- Why it happens
- Heat and vibration can loosen the tail/stop lamp bulb in its socket. Recall 04V527000 inspected and replaced the lamp assemblies.
- What to do
- Have someone check your brake lights. Check your VIN for the recall.
Free at a GM dealer if it was never done. Check your VIN first.
Blower runs only on some speeds or quits
- What you'll notice
- The fan works on only certain settings, stops completely, or keeps running with the key off.
- Why it happens
- The blower motor control module on this platform fails often; a revised module was released.
- What to do
- Replace the blower control module. If it runs with the key off, unplug it to save the battery until fixed.
Power window pops when going up
- What you'll notice
- A popping noise when raising a window.
- Why it happens
- The plastic guide on the window regulator, the same part used in the TrailBlazer, rubs the glass.
- What to do
- Tape on the regulator where it touches the glass is GM's fix; the regulator usually doesn't need replacing.
Rattle or clunk over bumps from stabilizer links
- What you'll notice
- A rattle, clunk or pop from the front on rough roads.
- Why it happens
- GM issued a bulletin calling for replacement of worn stabilizer links.
- What to do
- Have the front end inspected; links are inexpensive but rule out ball joints too.
Key or shifter can leave Park with the engine off (recall)
- What you'll notice
- The key comes out with the shifter not in Park, or the shifter moves out of Park with the engine off.
- Why it happens
- Mechanical overrides didn't meet federal theft-protection rules. Recall 03V075000 disabled them.
- What to do
- Always set the parking brake. Check your VIN for the recall.
Free at a GM dealer if it was never done. Check your VIN first.
Turn signals flash like hazards (recall)
- What you'll notice
- Using the turn signal makes all corner lights flash like hazards.
- Why it happens
- A faulty flasher module was replaced under recall 05V198000.
- What to do
- Check your VIN for the recall.
Free at a GM dealer if it was never done. Check your VIN first.
Repair prices for your Oldsmobile Bravada
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Transmission fluid and filter service as a first step
- Replace intake manifold gaskets with updated metal-core gaskets
- Replace central (spider) fuel injector assembly
- Replace distributor cap and rotor
- Clean throttle body and replace idle air control valve
- Transfer case fluid change
- Replace electronic fan clutch
- Replace ignition switch
- Replace blower motor control module
- Apply anti-noise tape to regulator; replace regulator if it fails
- Replace rear air compressor, or convert rear to coil springs
- Replace fuel tank (GM's fix for a leaking inlet check valve)
- Replace transfer case encoder/shift motor
- Replace front stabilizer links
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Inspect and modify per recallNo charge if your vehicle is included
- Repair wiper circuit or replace wiper motorNo charge if your vehicle is included
- Inspect and replace upper control arms/ball jointsNo charge if your vehicle is included
- Replace seat belt bucklesNo charge if your vehicle is included
- Replace rear axle brake pipeNo charge if your vehicle is included
- Inspect and torque lower control arm nutsNo charge if your vehicle is included
- Replace hazard switch carrierNo charge if your vehicle is included
- Replace front lower control arm bracketsNo charge if your vehicle is included
- Replace fuel filter quick-connect retainersNo charge if your vehicle is included
- Replace driver airbag moduleNo charge if your vehicle is included
- Install protective wiring harnessNo charge if your vehicle is included
- Reprogram instrument clusterNo charge if your vehicle is included
- Inspect and replace front seat belt retractorsNo charge if your vehicle is included
- Seal and repair wiper moduleNo charge if your vehicle is included
- Disable mechanical overridesNo charge if your vehicle is included
- Inspect and replace tail/stop lamp assembliesNo charge if your vehicle is included
- Replace left front brake pipeNo charge if your vehicle is included
- Replace flasher moduleNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.