Oldsmobile Silhouetteproblems, repair costs and recalls
Problems reported across 1997–2004. Pick your model year below to see what applies to your vehicle.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
27 documented issues across all years, most serious first.
Lower intake manifold gasket coolant leak
- What you'll notice
- Coolant level keeps dropping with no puddle you can trace, a sweet smell, the temperature gauge creeping up, or milky brown sludge under the oil cap. Some owners see white exhaust smoke.
- Why it happens
- The 3.4L V6 uses plastic-framed lower intake gaskets that break down over time, especially with old coolant. Coolant then leaks outside the engine or into the oil.
- What to do
- Check the coolant level often and do not let the engine overheat. Have a shop pressure-test the cooling system and replace the gaskets with the updated metal-framed type. If coolant got into the oil, change the oil right away to protect the bearings.
Overheating that damages the head gaskets
- What you'll notice
- The temperature gauge spikes, steam comes from under the hood, or the van runs hot in traffic. After a bad overheat you may get white smoke and a rough idle.
- Why it happens
- Usually the end result of a slow coolant leak, most often from the intake gaskets, that nobody caught in time. Running the engine hot can then blow a head gasket or warp a cylinder head.
- What to do
- Pull over and shut the engine off as soon as the gauge climbs. Do not keep driving it hot. Have the cooling system and head gaskets tested before deciding whether the repair is worth it.
Automatic transmission slipping or failing
- What you'll notice
- The engine revs up but the van barely speeds up, gears slip, it gets stuck in one gear, or it stops moving altogether.
- Why it happens
- The 4T65-E four-speed automatic wears out internally on many of these vans, often between 85,000 and 190,000 miles. Old fluid and heavy loads speed it up.
- What to do
- Check the fluid level and color. If it slips, do not tow or load the van until it is checked. A transmission shop can tell you whether a solenoid or a full rebuild is needed.
Power sliding door can open while driving (recall)
- What you'll notice
- The passenger-side power sliding door may close without fully latching, and then slide open while the van is moving.
- Why it happens
- Weak welds in the door's unlatch actuator can let it jam, so the latch never fully catches. GM ran two recalls (01V-067 and 01V-264) to fix it.
- What to do
- Have a GM dealer check your VIN for the open recall. Until it is done, keep kids buckled and check that the door is fully latched.
Free at any GM dealer if it was never done. Oldsmobile is gone, so call a Chevrolet, Buick or GMC dealer with your VIN.
Steering can suddenly get hard to turn (recall)
- What you'll notice
- The steering wheel becomes much harder to turn, as if the power steering quit.
- Why it happens
- Retainer tabs on the steering rack's lower pinion bearing were not crimped right, so bearing balls could escape. Recall 02V-286 covers it.
- What to do
- Have a dealer confirm the recall was done. If steering is already heavy, drive slowly to the shop and avoid highways.
Free at any GM dealer if it was never done. Oldsmobile is gone, so call a Chevrolet, Buick or GMC dealer with your VIN.
Steering shaft joint can come apart (recall)
- What you'll notice
- Loose or vague steering, clunks through the wheel, and in the worst case loss of steering.
- Why it happens
- Collapsed insulators can loosen a joint in the steering shaft so it could separate. GM recall 99V-071 covers it.
- What to do
- Get the recall status checked by VIN. Any looseness or clunk in the steering should be inspected right away.
Free at any GM dealer if it was never done. Oldsmobile is gone, so call a Chevrolet, Buick or GMC dealer with your VIN.
Wiper linkage can rub through a brake line (recall)
- What you'll notice
- A brake fluid leak under the windshield area, a soft brake pedal, or the brake warning light.
- Why it happens
- The windshield wiper linkage can rub against a traction control brake line until it wears through. Recall 98V-072 adds a clip and replaces damaged lines.
- What to do
- If the pedal feels soft or fluid is low, do not drive the van. Have the recall done and the brake lines checked.
Free at any GM dealer if it was never done. Oldsmobile is gone, so call a Chevrolet, Buick or GMC dealer with your VIN.
Fuel tank rollover valve may leak fuel (recall)
- What you'll notice
- Usually no warning at all. Some owners may notice a fuel smell.
- Why it happens
- On long-wheelbase vans, some fuel tank rollover valves did not work, so fuel could spill in a rollover. Recall 99V-268 replaces the tank.
- What to do
- Have a dealer check the VIN. Any fuel smell should be checked right away.
Free at any GM dealer if it was never done. Oldsmobile is gone, so call a Chevrolet, Buick or GMC dealer with your VIN.
Seat belt buckles may not hold in a crash (recall)
- What you'll notice
- No warning sign; the buckle looks and latches normally.
- Why it happens
- Some TRW buckle bases were not heat treated properly and may not be strong enough in a crash. Recall 00V-228 replaces affected buckles.
- What to do
- Ask a dealer to check the buckle date codes under recall 00V-228.
Free at any GM dealer if it was never done. Oldsmobile is gone, so call a Chevrolet, Buick or GMC dealer with your VIN.
Passenger airbag built without a part (recall)
- What you'll notice
- No warning sign; the airbag light may stay normal.
- Why it happens
- Some passenger airbags were made without a check valve pin, which could make the bag deploy harder than intended. Recall 02V-329 covers it.
- What to do
- Have a dealer check the VIN and replace the airbag if needed.
Free at any GM dealer if it was never done. Oldsmobile is gone, so call a Chevrolet, Buick or GMC dealer with your VIN.
Driver airbag inflator can crack (recall)
- What you'll notice
- No warning sign before a crash.
- Why it happens
- The driver airbag inflator could break at a weld when it fires, throwing pieces toward the driver and leaving the bag underfilled. Recall 02V-222 inspects and replaces it.
- What to do
- Have a dealer check whether the airbag module was inspected under the recall.
Free at any GM dealer if it was never done. Oldsmobile is gone, so call a Chevrolet, Buick or GMC dealer with your VIN.
Hard, harsh or erratic shifting
- What you'll notice
- Shifts slam or feel jerky, the van bangs into Drive or Reverse on cold mornings, or shifts flare and come late. The check engine light may come on.
- Why it happens
- GM issued several bulletins for this transmission covering worn pressure control solenoids, valve body problems and computer settings that cause harsh or erratic shifts.
- What to do
- Have the codes read and the fluid checked. Ask the shop about the GM bulletins for the 4T65-E; a solenoid or software fix is far cheaper than a rebuild if caught early.
Shudder on the 1-2 shift
- What you'll notice
- A shake or shudder when the transmission moves from first to second gear under light or moderate throttle.
- Why it happens
- GM traced this to the second-gear clutch pack inside the 4T65-E and released a bulletin to replace it.
- What to do
- Mention the shudder and the GM bulletin for the 1-2 shift to a transmission shop. Fresh fluid may help a little, but the real fix is internal.
Sliding door handle can trap a passenger's arm (recall)
- What you'll notice
- A passenger holding the inside handle of the power sliding door can have their arm or wrist pushed into the seat as the door opens by motor.
- Why it happens
- On vans with second-row bucket seats, the handle sits where the opening door can pin the passenger's arm. GM recall 04V-597 replaces the handle.
- What to do
- Ask a dealer whether the new handle was installed. Until then, open the door with the switch or key fob rather than the inside handle.
Free at any GM dealer if it was never done. Oldsmobile is gone, so call a Chevrolet, Buick or GMC dealer with your VIN.
Power sliding door won't open, close or latch
- What you'll notice
- The power sliding door stops partway, reverses on its own, chimes, or will not open or close at all.
- Why it happens
- The power door's motor, cable, latch and sensors wear out. GM issued several bulletins and a satisfaction campaign for door operation.
- What to do
- Try resetting the door by closing it by hand and cycling the power door switch. If it still fails, have the motor, cable and latch checked.
Rear seat release can injure fingers (recall)
- What you'll notice
- Fingers can get caught in the latch mechanism when folding or removing the rear bucket or split bench seats.
- Why it happens
- The seat latch mechanisms had no protective cover. Recall 98V-145 installs covers.
- What to do
- Keep fingers clear of the seat latches and ask a dealer to install the covers if they are missing.
Free at any GM dealer if it was never done. Oldsmobile is gone, so call a Chevrolet, Buick or GMC dealer with your VIN.
Hard starting, rough idle or misfire from fuel injectors
- What you'll notice
- Long cranking before it starts, a rough or shaky idle, a light misfire, or the check engine light.
- Why it happens
- GM bulletins cover clogged fuel injectors and injector corrosion on the 3.4L V6.
- What to do
- Have the misfire codes read. Injector cleaning or replacing the bad injectors usually fixes it.
ABS or traction control light on
- What you'll notice
- The ABS and traction control lights come on, and AWD models may show an AWD disabled message.
- Why it happens
- Wheel speed sensor faults and related wiring problems set codes; GM issued bulletins for this.
- What to do
- Have the ABS codes read. Normal braking still works, but anti-lock does not while the light is on.
Gauges sweep or fuel gauge reads wrong
- What you'll notice
- The gauges jump around or sweep on their own, warning lights flicker on, or the fuel gauge shows the wrong level.
- Why it happens
- GM bulletins cover erratic instrument clusters and inaccurate fuel gauges; a failing fuel level sender in the tank can also cause it.
- What to do
- Use the trip odometer to track fuel until it is fixed. Have the cluster and fuel sender tested to see which one is at fault.
Air conditioning blows warm
- What you'll notice
- The A/C blows warm or only slightly cool, especially in hot, humid weather.
- Why it happens
- Leaks, a worn compressor or clutch, and bulletins for weak A/C performance on these vans.
- What to do
- Have the system leak-tested before recharging it, so you are not paying to refill a leak.
Dead battery from the power sliding door
- What you'll notice
- The battery goes dead overnight or after a few days parked.
- Why it happens
- A GM bulletin covers battery drain on vans with power sliding doors, where the door system keeps drawing current after the van is shut off.
- What to do
- Have a shop do a parasitic drain test. If the door system is the cause, the bulletin repair stops the drain.
Child seat anchors in second row may not fit (recall)
- What you'll notice
- A child seat's lower anchor clips may not attach to the second-row anchors.
- Why it happens
- The second-row anchor wires were thicker than the federal standard allows. Recall 01V-383 covers it.
- What to do
- If a child seat will not latch to the anchors, use the seat belt to install it and ask a dealer about the recall.
Free at any GM dealer if it was never done. Oldsmobile is gone, so call a Chevrolet, Buick or GMC dealer with your VIN.
Ticking noise after a cold start
- What you'll notice
- A ticking or tapping from the engine right after starting cold that fades as it warms up.
- Why it happens
- GM issued a bulletin for this cold-start tick on the 3.4L V6.
- What to do
- If the noise fades and the oil level is fine, it is usually harmless. Have it checked if it stays loud when warm.
Weak heat at idle in cold weather
- What you'll notice
- The heater blows only lukewarm air at idle or low speed when it is below freezing.
- Why it happens
- GM bulletins describe poor cabin heat at low engine speed in cold weather on these vans.
- What to do
- Make sure the coolant is full, since low coolant from an intake gasket leak causes the same thing. Then ask a shop about the GM bulletin.
Water leaks at the windshield or overhead console
- What you'll notice
- Water drips from the overhead console or map light, or wet carpet up front after rain.
- Why it happens
- GM bulletins cover leaks at the center of the windshield seal and the overhead console area.
- What to do
- Have the windshield seal and roof area water-tested and resealed.
Tail lights or brake lights stop working
- What you'll notice
- One or more rear lights go out even with new bulbs, or the lights flicker.
- Why it happens
- The plastic socket plate that holds the rear bulbs melts or loses contact over time.
- What to do
- Replace the socket plate, not just the bulb, since working brake lights matter for safety.
Rust on the body and underside
- What you'll notice
- Rust bubbles on the body, rocker panels or wheel arches, and rusty parts underneath.
- Why it happens
- Age and road salt; owners report heavy rust on these vans at higher mileage.
- What to do
- Wash the underside in winter and have brake and fuel lines checked for rust at each service.
Repair prices for your Oldsmobile Silhouette
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace lower intake manifold gaskets and refill coolant
- Replace head gaskets (cylinder heads machined or replaced if warped)
- Rebuild or replace the automatic transaxle
- Replace pressure control solenoid or service valve body
- Replace second clutch assembly
- Repair power sliding door motor, cable or latch
- Diagnose parasitic drain and repair door circuit
- Clean or replace fuel injectors
- Replace wheel speed sensor or hub bearing
- Repair instrument cluster or replace fuel level sender
- Diagnose engine noise (bulletin repair if needed)
- Check coolant and apply heater bulletin repair
- Repair A/C leak or replace compressor
- Water-test and reseal windshield or roof
- Replace rear light socket plate
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Free dealer recall repairNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.