Saab 9-3problems, repair costs and recalls
Problems reported across 1999–2011. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
32 documented issues across all years, most serious first.
Oil sludge and oil starvation
- What you'll notice
- The oil pressure light flickers or comes on, the engine knocks or ticks, or it suddenly loses power. In bad cases the engine seizes with little warning.
- Why it happens
- On the early turbo four-cylinders, long oil-change intervals let sludge and carbon build up and clog the screen on the oil pickup in the pan. Heat from the nearby catalytic converter is thought to cook the oil. The oil light often only comes on once pressure is already gone.
- What to do
- If the oil light comes on, pull over and shut the engine off. On any car from these years, have a shop drop the oil pan and clean the pickup if the history is unknown, then change synthetic oil about every 5,000 miles.
Ignition module can overheat and stall the engine (recall)
- What you'll notice
- The engine misfires, runs rough or stalls while driving and may not restart.
- Why it happens
- A transistor inside the ignition discharge module (the ignition cassette that sits on top of the spark plugs) can overheat and burn out. Saab recalled modules built before a certain production change on these engines.
- What to do
- Have a Saab-knowledgeable shop or GM dealer check the module date code and whether the recall was done. A failing cassette is a common cause of misfires on these engines either way.
Timing chain or balance shaft chain rattle
- What you'll notice
- A rattle or chatter from the front of the engine, often worst on a cold start, sometimes with a check engine light or a new vibration.
- Why it happens
- The timing chain and the separate balance shaft chain wear out faster when the oil is dirty or sludged. Tensioners and plastic guides can break, and a broken guide can damage other parts.
- What to do
- Do not ignore a new rattle. Have the chains, guides and tensioner inspected; a chain that jumps a tooth can cause serious engine damage. Keep oil changes short and on schedule.
Worn intake valves causing hard cold starts and misfires
- What you'll notice
- Long cranking or no start in cold weather, a rough idle and misfire codes when cold, and the engine smoothing out once warm. Fuel economy may drop.
- Why it happens
- The intake valves on the 2.0T wear and stop sealing, so one or more cylinders lose compression. Owners and shops report this from roughly 55,000 miles onward.
- What to do
- Ask for a compression or leak-down test before replacing coils, plugs or sensors. If compression is low, the fix is a valve job on the cylinder head.
Turbocharger oil leak or failure
- What you'll notice
- Blue smoke on start-up, oil use between changes, a whistle or loss of boost, or oil around the turbo pipes.
- Why it happens
- Turbo seals wear, and a blocked oil return line or a leaking oil feed pipe can starve or flood the turbo. Sludged oil speeds this up.
- What to do
- Check the oil level often. Have the turbo, its oil lines and the crankcase ventilation checked before the turbo fails completely.
Steering column module (CIM) failure
- What you'll notice
- Turn signals stick on or work only sometimes, steering wheel controls stop working, alarm problems, or the car won't start.
- Why it happens
- The column integration module behind the steering wheel, which handles the signals, wipers and part of the anti-theft system, fails.
- What to do
- Have the module diagnosed with a Saab scan tool. A replacement module has to be programmed to the car.
Steering rack mount cracking the firewall
- What you'll notice
- Creaks from the steering, a loose or vague steering feel.
- Why it happens
- The steering rack bolts to the firewall, which flexes and can crack around the mounting points over time.
- What to do
- Have the rack mounting points inspected. Cracks are repaired by welding or a reinforcing brace.
Fuel pump or fuel gauge sender failure
- What you'll notice
- The engine cranks but won't start, stalls on the road, or the fuel gauge reads wrong.
- Why it happens
- The in-tank fuel pump or the fuel level sender fails. GM issued a bulletin on diagnosing pump and gauge faults.
- What to do
- Have fuel pressure tested before replacing parts. Don't run the tank very low if the gauge is unreliable.
Driver airbag inflator may rupture (recall)
- What you'll notice
- No warning sign; the danger is metal fragments if the airbag deploys.
- Why it happens
- The driver frontal airbag inflator can rupture from excess pressure.
- What to do
- Ask the dealer to confirm the recall applies to your VIN and have the free inflator replacement done.
Fuel pump may seize and stall the engine (recall)
- What you'll notice
- The engine stalls while driving or won't start.
- Why it happens
- Some fuel pumps were built with the wrong internal parts and can seize.
- What to do
- Check your VIN for open recalls and have the pump replaced free.
Fuel lines at the pump can loosen and leak (recall)
- What you'll notice
- Fuel smell or a fuel leak under the rear of the car.
- Why it happens
- Fuel pump retaining tabs were damaged in production, so the fuel lines can loosen. Saab added a securing bracket.
- What to do
- Stop driving if you smell fuel. Check the recall status with a dealer.
Brake booster check valve can fail (recall)
- What you'll notice
- The brake pedal suddenly gets hard and the car needs much more pedal force to stop.
- Why it happens
- Heat can damage the vacuum check valve for the brake booster, cutting power assist.
- What to do
- Get the recall status checked; a redesigned check valve is installed free.
Front seat belt may not retract on sedans (recall)
- What you'll notice
- The front seat belt stays loose and won't wind back in.
- Why it happens
- The retractor can be damaged in manufacturing and its cable may break.
- What to do
- Have the free retractor replacement done.
Convertible driver seat belt may not retract (recall)
- What you'll notice
- On the convertible, the driver's belt stays loose and won't retract.
- Why it happens
- The driver's front seat belt retractor can break.
- What to do
- Have the free retractor replacement done. The passenger side has lifetime special coverage.
Front seatback may fold forward in a crash (recall)
- What you'll notice
- No warning sign; the risk is in a frontal crash.
- Why it happens
- The front seat backrest lock may be installed wrong.
- What to do
- Have the dealer check recall completion.
Crankcase ventilation (PCV) failure causing oil leaks and smoke
- What you'll notice
- Oil leaks from seals and gaskets, oily residue, smoke from the engine bay or tailpipe, and in some cases sludge.
- Why it happens
- Clogged or broken crankcase ventilation hoses and valves let pressure build inside the engine. Saab issued updated ventilation parts for these engines.
- What to do
- Ask a shop to check the PCV hoses, check valves and drain box, and install the updated parts if they were never done.
Water pump leak
- What you'll notice
- Coolant drips under the front of the car, a sweet smell, the low-coolant warning, or the temperature gauge rising.
- Why it happens
- The water pump seal wears out. Owners report leaking pumps on both the 2.0T and 2.8 V6 from about 40,000 to 90,000 miles.
- What to do
- Top up with the correct coolant and have the leak traced. Replace the pump before it overheats the engine.
Coolant loss from cracked reservoir or hoses
- What you'll notice
- The low-coolant warning comes on again and again, sometimes with no visible puddle.
- Why it happens
- Expansion tanks crack, turbo coolant hoses leak, and on some V6 engines leaks have been traced to the cylinder heads. Some 2.0L engines lose coolant with no clear cause.
- What to do
- Have the cooling system pressure-tested. Don't keep topping up for months, because running low can overheat the engine.
Ignition coil failure causing misfire
- What you'll notice
- A flashing or steady check engine light, shaking at idle and loss of power.
- Why it happens
- Individual coils fail on both the 2.0T and the 2.8 V6. On the V6, the coil closest to the turbo sees the most heat, and corroded connectors can mimic a bad coil.
- What to do
- Have the misfire codes read to find which cylinder. Check the wiring connector before buying several coils.
Key fob or key chip failure
- What you'll notice
- The remote stops locking or unlocking, the alarm goes off when you use the key, or the car won't recognize the key and won't start.
- Why it happens
- The electronic key or its chip fails. Replacing it means buying a new key and programming it to the car.
- What to do
- Try a new battery in the fob first. If the key still isn't recognized, a dealer or Saab specialist must program a new one.
A/C compressor failure
- What you'll notice
- The A/C blows warm or cuts in and out.
- Why it happens
- Compressor failures were common on 2001-2002 cars, and later owners also report failed compressors. GM issued a bulletin for warm A/C on later cars.
- What to do
- Have the system pressures checked before recharging. If the compressor has failed, the system should be flushed when it is replaced.
Accelerator pedal sensor codes and reduced power
- What you'll notice
- Check engine light and the car goes into reduced power mode.
- Why it happens
- The ECM sets accelerator pedal position sensor codes (P2122, P2123, P2138 and similar). GM issued a bulletin for these on 2003-2009 Saabs.
- What to do
- Have the codes read and the pedal sensor and wiring checked.
Broken coil spring
- What you'll notice
- A clunk or bang over bumps, the car sitting lower at one corner, or uneven tire wear.
- Why it happens
- Gravel trapped between the coil spring and its seat wears the coating so the spring rusts and snaps. GM issued a bulletin on this.
- What to do
- Replace broken springs promptly, ideally in pairs. A broken spring can cut a tire.
Convertible top stops working
- What you'll notice
- The soft top won't open or close, or stops partway.
- Why it happens
- The soft-top control module can receive invalid signals. Sensors, hydraulics and switches can also fault.
- What to do
- Don't force the top. Have the soft-top system scanned; a bulletin covers the control module fault.
Oil leak from the oil level sensor
- What you'll notice
- Oil seeping from the bottom of the oil pan, small drips under the engine.
- Why it happens
- The seal on the oil level sensor in the oil pan leaks.
- What to do
- Have a shop replace the sensor seal. It is a small job, but keep an eye on the oil level until it is done.
Thermostat stuck open
- What you'll notice
- The temperature gauge stays low, the heater is weak, and a check engine light may come on.
- Why it happens
- The thermostat sticks partly open so the engine never reaches its normal temperature.
- What to do
- Replace the thermostat. An engine that runs cold wastes fuel and wears faster.
Power windows reopening slightly after closing
- What you'll notice
- A window goes all the way up, then drops back down about two inches by itself.
- Why it happens
- The anti-pinch function thinks it has met an obstruction, often because the window has lost its learned top position or the glass channel is binding.
- What to do
- A shop can re-learn the window positions and adjust the glass. It's usually a quick fix.
Power window regulator or motor failure
- What you'll notice
- A window moves slowly, makes grinding or clicking noises, or won't move at all.
- Why it happens
- Window regulators and motors wear out on these cars.
- What to do
- Have the door panel removed to see whether the motor, regulator or switch has failed.
Broken heater air-direction control shaft
- What you'll notice
- Turning the air-direction knob does nothing, so air won't switch between face, feet and windshield.
- Why it happens
- A plastic telescopic shaft behind the dash breaks after repeated flexing.
- What to do
- The replacement shaft is inexpensive and can be reached from the side of the center console.
Information display (SID) missing pixels
- What you'll notice
- Letters and numbers on the dash information display fade or have missing lines, making messages hard to read.
- Why it happens
- The small LCD screen in the Saab Information Display wears out.
- What to do
- Only the LCD needs replacing, not the whole unit. Saab specialists and DIY kits handle this.
Worn stabilizer bar end links
- What you'll notice
- Knocking or rattling from the front over small bumps.
- Why it happens
- The end links and bushings for the stabilizer (sway) bar wear out. It's one of the most-reported repairs on the 9-3.
- What to do
- An inexpensive repair; replace both sides.
Sunroof binding, noise or water leak
- What you'll notice
- The sunroof stops, reverses on its own, makes noise or lets water in.
- Why it happens
- Pinch-protection software, the wind deflector and clogged drains cause trouble. Saab and GM issued bulletins.
- What to do
- Clear the drains and ask about the software update.
Repair prices for your Saab 9-3
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Drop oil pan, clean sludge and oil pickup, update crankcase ventilation
- Replace timing or balance shaft chain, guides and tensioner
- Cylinder head valve job (replace intake valves)
- Replace turbocharger and oil feed/return lines
- Replace PCV hoses, check valves and drain box (update kit)
- Replace water pump and coolant
- Replace coolant expansion tank or leaking hose
- Reseal or replace oil level sensor
- Replace thermostat and refill coolant
- Replace ignition coil(s)
- Replace and program column integration module
- Replace and program key/remote
- Adjust window and re-learn anti-pinch positions
- Replace window motor/regulator assembly
- Replace A/C compressor, receiver/drier and recharge
- Replace air-direction control shaft
- Repair firewall cracks and fit a steering rack brace
- Replace in-tank fuel pump/sender assembly
- Diagnose accelerator pedal sensor codes (pedal sensor and wiring check)
- Replace front coil springs (one or a pair)
- Replace both front stabilizer bar end links
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Replace ignition discharge moduleNo charge if your vehicle is included
- Replace driver airbag inflatorNo charge if your vehicle is included
- Replace fuel pumpNo charge if your vehicle is included
- Install fuel line securing bracketNo charge if your vehicle is included
- Install redesigned vacuum check valveNo charge if your vehicle is included
- Replace front seat belt retractorNo charge if your vehicle is included
- Replace driver seat belt retractorNo charge if your vehicle is included
- Replace affected front seatNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.