Toyota Camryproblems, repair costs and recalls
Problems reported across 1996–2026. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
46 documented issues across all years, most serious first.
Engine oil sludge (oil gel)
- What you'll notice
- Oil pressure light, ticking or knocking, rising oil consumption, and in bad cases sudden engine failure, often on cars with stretched oil-change intervals.
- Why it happens
- Oil in these engines could thicken into a gel-like sludge that blocks oil passages. Toyota acknowledged it with a special policy that extended coverage for sludge damage.
- What to do
- If the oil light comes on or the engine knocks, stop and have it checked before driving further. Keep oil changes short and use the correct oil.
Stripped cylinder head bolt threads
- What you'll notice
- Slow coolant loss with no visible leak, coolant seeping near the back of the engine, overheating, or symptoms that look like a blown head gasket.
- Why it happens
- The head bolt threads in the aluminum engine block can pull out, letting the head gasket lose its clamping force. Toyota published a repair procedure using thread inserts.
- What to do
- Stop driving if the temperature gauge climbs. A shop can confirm it and install thread inserts; ignoring it can ruin the engine.
Excessive oil consumption
- What you'll notice
- Oil level drops quickly between changes, low-oil warning, blue-tinted exhaust smoke.
- Why it happens
- The piston rings can clog and let oil burn in the cylinders. Toyota ran a warranty enhancement program (ZE7) for it, which has since expired.
- What to do
- Check the oil at every fill-up and top it off. Do not keep driving with low oil; a shop can confirm with an oil consumption test and discuss a piston and ring repair.
Driver's power window switch can overheat (recall)
- What you'll notice
- Window switch that works on and off, feels sticky or hot, or a burning or melting smell from the driver's door.
- Why it happens
- Uneven lubrication inside the master window switch could make it overheat and melt, creating a fire risk. Toyota recalled the switch.
- What to do
- Check the VIN for open recalls. If you smell burning or see smoke from the door, stop using the switch and have it repaired right away.
Accelerator pedal can be trapped by floor mat (recall)
- What you'll notice
- Gas pedal stays down or the car keeps accelerating after you lift your foot.
- Why it happens
- An unsecured or wrong floor mat could catch the gas pedal. Toyota reshaped the pedal, replaced mats and added brake-override software under recall.
- What to do
- Check the VIN for open recalls and use only a properly secured, correct mat. If the pedal sticks, brake firmly, shift to Neutral and stop safely.
VVT-i oil hose leak
- What you'll notice
- Sudden oil leak at the front of the engine, oil pressure warning light, and abnormal engine noise.
- Why it happens
- The rubber section of the oil hose that feeds the variable valve timing system can break down with age and burst. Toyota ran a service campaign to replace it with a redesigned hose.
- What to do
- If the oil light comes on, pull over and shut the engine off. Have a dealer check whether the updated line was installed.
Hybrid brake actuator or brake control unit failure
- What you'll notice
- Brake and ABS warning lights and a change in how the brakes feel.
- Why it happens
- The hybrid's electronic brake actuator and its control unit and pedal sensor can fail. Toyota extended coverage on these parts with a warranty enhancement program (ZE1).
- What to do
- Have the brakes checked promptly when the brake warning lights come on, and ask a dealer about the extended coverage.
Water leak onto airbag control module (recall)
- What you'll notice
- Airbag warning light, heavy steering from loss of power assist, or in rare cases an airbag going off.
- Why it happens
- A clogged air conditioning drain (spider webs were one cause) could let water drip onto the airbag control module and short it out.
- What to do
- Check the VIN for this recall. If the airbag light comes on or steering suddenly gets heavy, have it inspected right away.
Fuel pump may fail (recall)
- What you'll notice
- Check engine light, rough running, failure to start, or the engine stalling while driving.
- Why it happens
- The low-pressure fuel pump in the tank could stop working. Toyota recalled it and replaces the pump.
- What to do
- Check the VIN for these recalls and get the pump replaced. A stall at speed is dangerous, so do not put it off.
Brake vacuum pump failure (recall)
- What you'll notice
- Brake pedal suddenly gets hard and the car takes much longer to stop, sometimes with a brake warning.
- Why it happens
- Part of the engine-driven vacuum pump that powers the brake booster can wear and break, cutting off power assist.
- What to do
- Check the VIN for this recall. If the pedal turns hard, press much harder, stop safely and have the car repaired before driving on.
Accelerator cable can wear through on V6 cruise control cars (recall)
- What you'll notice
- The engine keeps pulling or the speed does not drop when you lift off the gas pedal.
- Why it happens
- On V6 cars with cruise control, the accelerator cable housing can deform where it meets the cruise actuator, letting the inner cable fray and hang up.
- What to do
- If the throttle ever sticks, brake firmly, shift to Neutral and pull over. Do not keep driving until a dealer has checked the cable and the recall status.
Rear axle part may be weak from improper heat treatment (recall)
- What you'll notice
- There may be no warning. A grinding or clunking from a rear wheel, or a rear wheel that looks tilted, is a serious sign.
- Why it happens
- Some rear axle shafts were not heat treated correctly at the factory and can break.
- What to do
- Have a dealer run the VIN for this recall. If a rear wheel makes new noises or looks out of position, stop driving and have the car towed.
Front subframe may be poorly welded (recall)
- What you'll notice
- Clunks from the front end, wandering steering or uneven tire wear that keeps coming back, usually after many years of use.
- Why it happens
- On some cars the front subframe, which carries the engine and front suspension, did not get adequate welds and can fail over time.
- What to do
- Check the VIN for this recall. If the front end clunks or the steering feels loose, have it inspected before driving further.
Front lower control arm can separate from ball joint (recall)
- What you'll notice
- A clunk from the left front, loose steering, or a front wheel that suddenly folds outward.
- Why it happens
- Some left front lower arms were made without the proper clamping area for the ball joint bolt, so the joint can work loose.
- What to do
- Check the VIN right away. If you hear front-end clunks, stop driving and have the car inspected.
Fuel delivery pipe may leak (recall)
- What you'll notice
- A raw fuel smell from under the hood, sometimes with a visible wet spot on the engine.
- Why it happens
- The pipe that feeds fuel to the injectors can leak, and fuel on a hot engine can catch fire.
- What to do
- If you smell fuel, stop driving and have the car towed to a dealer. Check the VIN for this recall either way.
Oversized pistons can cause stalling (recall)
- What you'll notice
- Rough running, engine noise, smoke, a warning light, or the engine shutting off while driving.
- Why it happens
- A small batch of 2.5L engines was built with pistons larger than specified, which can damage the engine.
- What to do
- If the engine runs rough or stalls, stop driving. Have a dealer check the VIN; affected engines were replaced.
V6 fuel pipes may not be fully connected (recall)
- What you'll notice
- A strong fuel smell from the engine bay.
- Why it happens
- On some V6 cars the fuel delivery pipes were not properly joined to their hoses at the factory, so fuel can leak near hot parts.
- What to do
- If you smell fuel, park outside, do not drive, and have the car towed to a dealer. Check the VIN for this recall.
Engine can leak coolant from porous castings (recall)
- What you'll notice
- Dropping coolant level, temperature warning, sweet smell, or the engine stalling. Coolant may also get inside the engine.
- Why it happens
- Some 2.5L engine castings were porous and can crack, leaking coolant inside or outside the engine. That can lead to overheating, oil leaks and a fire risk.
- What to do
- If the temperature warning comes on or coolant keeps disappearing, stop driving. Have a dealer check the VIN; affected engines were inspected and replaced.
Wheel lug nuts may be loose (do-not-drive recall)
- What you'll notice
- Clicking or knocking from a wheel, vibration that gets worse, or a wheel that wobbles.
- Why it happens
- On a limited group of cars the lug nuts may not have been tightened properly, so a wheel can come off.
- What to do
- Toyota advised owners of affected cars not to drive until repaired. Check the VIN, and have the lug nuts torqued before driving if it applies.
Hybrid inverter bolt may be loose (recall)
- What you'll notice
- A hybrid system warning appears and the car can suddenly lose drive power while you are moving.
- Why it happens
- A bolt inside the inverter may not have been tightened at the factory, so the connection can arc, short out and in the worst case start a fire.
- What to do
- Have the dealer check the VIN and carry out the recall right away; do not put off driving it in for this one.
Harsh or jerky automatic shifts
- What you'll notice
- Hard, clunky shifts, especially the 2-3 upshift or when slowing down, and an occasional jolt when the transmission changes gear.
- Why it happens
- Shift programming in the engine computer caused firm or poorly timed shifts. Toyota released a computer recalibration to smooth shifting.
- What to do
- Ask a Toyota dealer whether the shift recalibration has been done and have the fluid level and condition checked.
Shudder at light throttle
- What you'll notice
- A brief vibration or shudder, often around 25-50 mph under light acceleration, as the transmission locks up.
- Why it happens
- The torque converter clutch can engage roughly. Toyota released a software update (LSC E03) and extended torque converter coverage (ZE5) if the update did not cure it.
- What to do
- Ask a dealer whether the software update was done. If the shudder remains, the torque converter may need replacing.
Rough or hesitant shifting
- What you'll notice
- Harsh engagement into gear when cold, abrupt 1-2 shifts, hunting for gears, or hesitation pulling away.
- Why it happens
- Shift programming on the 8-speed automatic. Toyota issued bulletins to reprogram the engine and transmission computer.
- What to do
- Ask the dealer whether the latest software update has been applied, and report it again if shifting stays harsh.
Key can be removed when not in Park (recall)
- What you'll notice
- The key comes out of the ignition with the shifter still in gear, so the car can roll after you walk away.
- Why it happens
- A lock pin in the key interlock solenoid can jam, defeating the feature that holds the key until the shifter is in Park.
- What to do
- Always set the parking brake, and ask a Toyota dealer to check whether this recall is still open on your car.
Side curtain airbags may be twisted (recall)
- What you'll notice
- Nothing you would notice while driving. The problem only shows up in a side crash.
- Why it happens
- On cars with curtain airbags, the folded bag could be twisted near its inflator during assembly, which slows it down when it fires.
- What to do
- Check the VIN with a Toyota dealer and have the recall inspection done if it is still open.
Crankshaft pulley outer ring can slip on V6 engines (recall)
- What you'll notice
- A squeal or chirp from the belts, a belt that comes off, and steering that suddenly gets heavy.
- Why it happens
- The outer ring of the crankshaft pulley was bonded with too little adhesive. It can shift out of line and throw the power steering belt.
- What to do
- If the steering turns heavy or a belt comes off, pull over and have it repaired. Ask a dealer whether the pulley recall has been done.
Windshield wiper switch can short out (recall)
- What you'll notice
- Wipers that stop working or act up, sometimes in the rain when you need them.
- Why it happens
- The wiper switch assembly on the steering column can develop an internal short.
- What to do
- Have the recall done at a Toyota dealer. If the wipers quit in bad weather, pull over until you can see safely.
Power steering assist can cut out (recall)
- What you'll notice
- The steering suddenly becomes heavy, usually with a power steering warning light.
- Why it happens
- A part inside the electric power steering computer was damaged during manufacturing and can fail.
- What to do
- You can still steer with more effort. Slow down, pull over when safe, and have a dealer check the recall status.
Passenger airbag sensor miscalibrated (recall)
- What you'll notice
- The passenger airbag status light may not match who is sitting in the seat.
- Why it happens
- The seat sensor that classifies the front passenger was not calibrated correctly on cars built over a few months, so the airbags may not fire as intended.
- What to do
- Have a Toyota dealer check the VIN and recalibrate the sensor if the recall is open.
Passenger knee airbag attached with wrong fasteners (recall)
- What you'll notice
- Nothing noticeable in normal driving.
- Why it happens
- On cars from a short build window, the front passenger knee airbag was installed with incorrect fasteners that can loosen and affect how the bag deploys.
- What to do
- Check the VIN with a dealer and have the fasteners replaced if the recall applies.
Passenger seat sensor can short and disable the airbag (recall)
- What you'll notice
- An airbag warning light, or a passenger airbag status light that is wrong for the person seated.
- Why it happens
- The sensors in the front passenger seat that detect an occupant can short circuit, which may stop the passenger airbag from deploying.
- What to do
- Check the VIN with a Toyota dealer and have the sensors inspected or replaced.
Rear seat head restraint brackets may be weakly welded (recall)
- What you'll notice
- Usually nothing; a rear head restraint may feel loose or rattle.
- Why it happens
- The brackets that hold the second-row head restraints did not get strong enough welds on some cars, so they may not protect a rear passenger in a crash.
- What to do
- Check the VIN with a dealer and have the rear seat back parts replaced if the recall is open.
Instrument display can go blank after starting (recall)
- What you'll notice
- The gauge screen stays dark when you start the car, and the turn signal and hazard indicators, seat belt reminder and key reminder do not show.
- Why it happens
- A software fault in the instrument display keeps it from waking up properly at start-up.
- What to do
- Get the free software update at a Toyota dealer; until then watch your speed closely, since the speedometer may not be visible.
Knocking from worn front strut mounts and sway bar links
- What you'll notice
- Knocking, clunking or rattling from the front end over bumps and rough pavement, sometimes felt through the steering wheel.
- Why it happens
- The rubber in the strut mounts and the small stabilizer bar links wears out, so metal parts move against each other.
- What to do
- Have the front suspension inspected soon; worn mounts and links change how the car handles and should not be left for long.
Water pump leaks coolant
- What you'll notice
- A sweet smell, pink or green drips near the front of the engine, low coolant in the tank and the temperature gauge creeping up.
- Why it happens
- The seal and bearing in the water pump wear out and let coolant escape where the pump bolts to the engine.
- What to do
- Get it replaced before it fails completely, because losing coolant can overheat and ruin the engine. On V6 models the timing belt comes off for this job.
Alternator stops charging
- What you'll notice
- A battery shaped warning light while driving, dimming lights, a slow crank the next morning or the car dying on the road.
- Why it happens
- The brushes and bearings inside the alternator wear out, so it no longer keeps the battery charged.
- What to do
- Have the charging system tested and the alternator replaced; once the light is on you may only have a short distance left.
Check Brake System message at startup
- What you'll notice
- A brake system message and warning lights appear when you start the car, and sometimes clear on their own after a while.
- Why it happens
- The brake control unit stores fault codes, usually traced to a sensor or its wiring. Toyota published a diagnostic bulletin for this exact complaint.
- What to do
- Have the stored codes read. The brakes normally still work, but while the message is there it hides any real brake fault, so do not leave it.
Automatic transmission fluid leak at the oil pan gasket
- What you'll notice
- Red fluid drips or a damp film builds up on the bottom of the transmission, and you may find small spots where you park.
- Why it happens
- The gasket between the transmission oil pan and the case seeps. Toyota covered it in a bulletin with a revised sealing procedure.
- What to do
- Have the leak traced and the pan resealed. If the fluid gets low the transmission can start slipping, which is a much bigger bill.
Hybrid battery cooling fan clogged with dust
- What you'll notice
- The check engine light comes on in a hybrid, often with a hybrid system warning, and the fan behind the rear seat may run louder or longer than usual.
- Why it happens
- Dust and debris collect in the hybrid battery cooling fan and its duct, so the battery pack runs warmer and the control system logs a fault.
- What to do
- Have the fan and duct cleaned as the Toyota bulletin describes. Letting the pack run hot shortens its life.
Sticky, melting or cracked dashboard
- What you'll notice
- The dash top turns shiny and tacky, gives off glare on the windshield, or cracks.
- Why it happens
- The dashboard material breaks down with heat and humidity. Toyota offered a warranty enhancement program (ZE6) for cracked or sticky dashboards.
- What to do
- Mostly cosmetic, but glare can hurt visibility. Ask a dealer whether any coverage still applies; a dash cover is a simple fix.
Musty or moldy smell from the A/C
- What you'll notice
- A sour or mildew smell from the vents, mostly when the A/C first turns on.
- Why it happens
- Moisture and debris collect on the A/C evaporator and allow mold to grow. Owners filed a class action over it, and part of it has been settled.
- What to do
- Replace the cabin filter and have the evaporator cleaned. Ask a dealer about any A/C odor bulletins or settlement coverage.
Tail light bulb holder can lose contact (recall)
- What you'll notice
- A tail or brake light that flickers or stops working even with a good bulb.
- Why it happens
- The plastic bulb holder was not heat resistant enough, so it can deform and let the bulb lose its electrical contact.
- What to do
- Have a helper check your rear lights. A dealer can confirm whether the recall was done on your car; otherwise the bulb holder is a simple replacement.
Valve cover gasket oil leak
- What you'll notice
- A burnt oil smell after driving, oil spots on the engine or a slow drop in the oil level, often with no puddle on the ground.
- Why it happens
- The rubber gasket under the valve cover hardens with heat and age and stops sealing, so oil seeps out of the top of the engine.
- What to do
- Have the gasket replaced and keep an eye on the oil level in the meantime; it is a slow leak but it can drip onto hot parts and smoke.
Front oxygen sensor fails and lights the check engine light
- What you'll notice
- Check engine light, slightly worse gas mileage and sometimes a rough or hesitant feel at light throttle.
- Why it happens
- The front air/fuel ratio sensor in the exhaust ages and stops reporting accurately, so the engine computer sets a code.
- What to do
- Have the code read and the sensor replaced; it is not urgent, but a lazy sensor wastes fuel and can fail an emissions test.
Knocking or popping from the moonroof area
- What you'll notice
- A knock, pop, tick or snap comes from the roof near the windshield as you drive over bumps and uneven pavement.
- Why it happens
- Parts of the moonroof assembly shift and rub against each other. Toyota published a revised repair for the noise.
- What to do
- This is not a safety problem. A dealer or body shop can carry out the bulletin repair if the noise bothers you.
Squeak from the front stabilizer bar bushings
- What you'll notice
- A dry squeak or creak from the front of the car at low speed, worst over driveways, speed bumps and dips.
- Why it happens
- The rubber bushings that hold the front stabilizer bar lose their lubrication and bind on the bar as it twists.
- What to do
- Safe to keep driving. The bushings can be lubricated or replaced the way the Toyota bulletin describes.
Repair prices for your Toyota Camry
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Remove oil pan and valve covers, clean out sludge, fresh oil
- Remove head, install thread inserts, new head gasket and bolts
- Reprogram transmission computer and check fluid
- Replace pistons and rings
- Replace upper dashboard panel
- Replace driver's master window switch
- Modify or replace accelerator pedal and fit correct mats
- Replace rubber VVT-i oil hose with updated metal line
- Replace hybrid brake actuator and bleed brakes
- Replace torque converter (after software update fails)
- Replace airbag control module and seal the leak
- Clean A/C evaporator and replace cabin air filter
- Update transmission software
- Replace in-tank fuel pump
- Replace brake vacuum pump
- Replace tail light bulb holder
- Replace key interlock solenoid
- Replace accelerator cable
- Replace rear axle hub carrier/spindle
- Replace front subframe
- Inspect and replace side curtain airbag
- Replace crankshaft pulley
- Replace windshield wiper switch
- Replace front lower control arm
- Replace fuel delivery pipe
- Replace electric power steering control unit
- Recalibrate occupant classification sensor
- Replace knee airbag fasteners
- Replace engine assembly
- Replace fuel delivery pipes and hoses
- Replace occupant classification sensors
- Inspect and torque wheel lug nuts, replace damaged studs
- Replace rear seat back frame/head restraint brackets
- Replace hybrid inverter assembly
- Update instrument display software
- Replace valve cover gasket
- Replace front strut mounts and stabilizer bar links
- Replace water pump
- Replace alternator
- Replace front air/fuel ratio sensor
- Service moonroof assembly per bulletin
- Replace front stabilizer bar bushings
- Diagnose brake system codes, repair sensor or wiring
- Reseal transmission oil pan and refill fluid
- Clean hybrid battery cooling fan and duct
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.