Toyota Sequoiaproblems, repair costs and recalls
Problems reported across 2001–2025. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
25 documented issues across all years, most serious first.
Front lower ball joint wear and separation (recall)
- What you'll notice
- Clunking from the front over bumps, steering that wanders, uneven wear on the inner edge of the front tires, and in the worst case a front wheel that suddenly folds under the truck.
- Why it happens
- The front lower ball joints on these trucks can wear out far too early. Toyota recalled 2002-2004 trucks because the ball surface could be scratched at the factory, and 2004-2007 trucks because the grease inside could break down. Some aftermarket replacement joints were also recalled for being too soft.
- What to do
- Have a Toyota dealer run your VIN for the ball joint recalls. If you hear clunking or the steering feels loose, get the front end inspected before driving at speed, because a separated joint can cause a loss of control.
Free at a Toyota dealer for trucks covered by the recall. Trucks outside the recall pay for the repair.
Passenger airbag inflator can rupture (Takata recall)
- What you'll notice
- Usually no warning signs at all. The danger only shows up in a crash, when the passenger front airbag deploys.
- Why it happens
- These trucks used Takata passenger airbag inflators whose propellant breaks down after years of heat and humidity. In a crash the inflator can burst and throw metal fragments into the cabin. Some inflators that were already replaced once were recalled again.
- What to do
- Ask a Toyota dealer to check your VIN for open recalls today. The replacement is free, and until it is done nobody should ride in the front passenger seat.
Frame rust (frame replacement program)
- What you'll notice
- Rust scaling, flaking or perforation on the frame rails and crossmembers, usually worst in snowy states that salt the roads.
- Why it happens
- Some frames from these years did not have enough rust protection. Toyota ran corrosion-protection and frame replacement programs, and a class action settlement covered inspections, rust-proofing and frame replacement for 2005-2008 Sequoias.
- What to do
- Have the frame inspected promptly. Ask a Toyota dealer whether your VIN was covered by the frame or corrosion-proofing programs, and do not tow with a badly rusted frame.
Side curtain airbags may deploy on their own (recall)
- What you'll notice
- No warning beforehand. The side curtain airbags can go off when the truck has not crashed, for example while off-roading or on a rough road.
- Why it happens
- The airbag control module on trucks with roll-sensing curtain airbags could be programmed in a way that triggers deployment when it should not.
- What to do
- Check your VIN for recall 16V-065 and have the free fix done.
Power steering gear can leak and lose assist (recall)
- What you'll notice
- Red or brown fluid dripping under the front, a low power steering reservoir, a whine when turning, or steering that suddenly becomes very heavy.
- Why it happens
- Some power steering gear assemblies were built in a way that lets oil leak out. If enough fluid is lost, the power assist can drop out without warning. Some replacement gears sold as parts were also recalled.
- What to do
- Check your VIN for recalls 21V-920 and 21E-103. Do not let the reservoir run dry, and have any leak looked at soon.
Sticking accelerator pedal (recall)
- What you'll notice
- The gas pedal feels stiff, is slow to come back up, or stays partly pressed when you let off.
- Why it happens
- Wear and moisture inside the pedal assembly can increase friction on a lever in the pedal, so it does not return smoothly.
- What to do
- Check your VIN for recall 10V-017. If the pedal sticks while driving, shift to Neutral, brake firmly and pull over.
Driver's power window switch can overheat (recall)
- What you'll notice
- Windows that work only some of the time, a burning smell or melted look at the driver's window switch, or smoke from the door panel.
- Why it happens
- The grease on the master window switch contacts was applied unevenly at the factory. Dirt and moisture can then cause a short that overheats the switch.
- What to do
- Stop using the switch if you smell burning. Check your VIN for recalls 12V-491 and 15V-689 and have the free repair done.
Fuel pump can fail and stall the engine (recall)
- What you'll notice
- Rough running, a check engine light, hard starting, or the engine cutting out while driving and not restarting.
- Why it happens
- The low-pressure fuel pump inside the tank can stop working properly and cut fuel to the engine.
- What to do
- Check your VIN for recalls 20V-012 and 20V-682 and have the pump replaced for free. A stall in traffic is dangerous, so do not wait.
Airbags may not deploy after a false fault (recall)
- What you'll notice
- The airbag warning light comes on at startup. On 2018 trucks the stability control light may also come on.
- Why it happens
- Electrical noise could make the airbag computer think it had a fault, which could stop the airbags from deploying in a crash. On some 2018 trucks the same noise could also turn off stability control.
- What to do
- Check your VIN for recalls 18V-685 and 18V-122. The fix is a free software update at a Toyota dealer.
Twin-turbo V6 engine failure reports
- What you'll notice
- Knocking from the engine, a sudden loss of power, or an engine that stops and will not restart. Some owners have reported the engine seizing.
- Why it happens
- The same twin-turbo V6 family in the non-hybrid Tundra and Lexus LX 600 was recalled for machining debris left in the engine that can damage the bearings. The hybrid Sequoia has not been part of that recall, but a small number of owners have reported engine failures.
- What to do
- Use the correct oil and change it on time. If you hear knocking or lose power, stop and have the SUV towed to a Toyota dealer, since the engine is covered by Toyota's powertrain warranty for the first years.
SUV can creep forward in Neutral (recall)
- What you'll notice
- With the shifter in Neutral on flat ground and no foot on the brake, the SUV slowly rolls forward at a few miles per hour.
- Why it happens
- Clutches inside the 10-speed automatic may not fully let go in Neutral, so some power still reaches the wheels.
- What to do
- Check your VIN for recall 24V-125. Until the free software update is done, use Park and the parking brake when stopped instead of Neutral.
Tires may have sidewall damage (recall)
- What you'll notice
- Usually nothing obvious from the driver's seat. You might see a bulge or cut on the inside sidewall of a passenger-side tire, or feel a vibration.
- Why it happens
- Some passenger-side tires could have damage on the inner sidewall, which can lead to a sudden air loss.
- What to do
- Check your VIN for recall 24V-767 and have the tires inspected and replaced if needed.
Cracked exhaust manifold
- What you'll notice
- A ticking or tapping from the engine on a cold start that often fades as it warms up. You may also smell exhaust or see a check engine light.
- Why it happens
- The cast iron exhaust manifolds on the 4.7L V8 crack after years of heating and cooling, most often on the driver's side. Exhaust then leaks out of the crack before it reaches the rest of the exhaust.
- What to do
- Have a shop confirm the leak. A quick check is soapy water sprayed on a cold manifold while the engine starts. Fix it before fumes get into the cabin or the leak throws off the oxygen sensors.
Secondary air injection pump or valve failure
- What you'll notice
- Check engine light with codes in the P2440-P2445 range, a loud buzz or whine right after a cold start, and sometimes a rough cold idle or a failed emissions test.
- Why it happens
- The air pump and its switching valves blow fresh air into the exhaust for a minute or two after a cold start. Water can get inside them, and they rust until the pump seizes or a valve sticks. Toyota issued a bulletin on water getting into the pumps and extended coverage on these parts for some years.
- What to do
- Have the codes read and the pump and valves tested. Ask a Toyota dealer whether any extended coverage applies to your VIN before paying for parts.
ABS and VSC lights from a faulty yaw rate sensor
- What you'll notice
- The ABS and VSC (stability control) warning lights come on together, sometimes flashing, often with codes C1223 and C1244.
- Why it happens
- A sensor under the center console that measures how the truck is turning or slowing can fail or be knocked out of position by a bent bracket. With bad readings, the system shuts off ABS and stability control.
- What to do
- Have the brake system codes read. Normal braking still works, but ABS and stability control may be off until the sensor is replaced or its mounting fixed.
Stability control can kick in at low speed (recall)
- What you'll notice
- When pulling away or accelerating at low speed, the stability control engages briefly on its own and the truck feels like it is holding back.
- Why it happens
- On some 2003 Sequoias the skid control computer did not store the steering angle sensor's center position correctly, so it thought the truck was sliding when it was not.
- What to do
- Ask a Toyota dealer to check your VIN for this recall. The fix is a free reprogramming.
Front brakes wearing out early
- What you'll notice
- Front pads wear out much faster than expected, often with grinding, squealing, uneven pad wear or a pull when braking.
- Why it happens
- The Sequoia is very heavy for its front brakes. In salty areas the caliper slide pins can also rust and seize, so the pads drag and wear unevenly.
- What to do
- Have the brakes checked at every tire rotation. When replacing pads, make sure the slide pins are cleaned and greased or replaced.
Seat heater wiring can short and burn (recall)
- What you'll notice
- A heated seat that stops working, gets very hot in one spot, or a burning smell from the seat.
- Why it happens
- Repeated sitting and getting in and out can damage the seat heater wiring in the cushion until it shorts. Some dealer-installed aftermarket seat heaters had the same risk and were recalled separately.
- What to do
- Stop using the seat heater if it smells or overheats. Have a Toyota dealer check your VIN for the seat heater recalls.
Leaking water pump
- What you'll notice
- Pink crusty residue around the water pump, low coolant, a whine or grinding from the front of the engine that rises with engine speed, or the temperature gauge creeping up.
- Why it happens
- The water pump bearing wears out and the seal behind it starts leaking coolant out of the weep hole. Toyota published a bulletin on inspecting these pumps for leaks.
- What to do
- Watch the coolant level and replace a leaking or noisy pump before the engine overheats. Make sure the leak is not actually coming from the timing cover above it.
Hybrid system malfunction warning with loss of power
- What you'll notice
- A 'Hybrid System Malfunction' warning on the dash, a sudden jerk, and the SUV not accelerating normally.
- Why it happens
- The cause has not been pinned down publicly. Owners of 2023 and 2024 models have reported it, and no recall has been issued so far.
- What to do
- Pull over safely, then have a Toyota dealer read the stored codes while they are fresh. Ask about any software updates for the hybrid system.
Backup camera image may not appear (recall)
- What you'll notice
- When you shift into reverse, the center screen shows a black or green screen, half a green screen, or a frozen picture instead of the camera view.
- Why it happens
- Electrical noise in the video signal to the multimedia screen can scramble the camera data so the picture does not display.
- What to do
- Check your VIN for recall 25V-657 and have the free software update done. Until then, check mirrors and look over your shoulder when backing up.
Spare tire can drop from its carrier (recall)
- What you'll notice
- A rattle or dragging sound from under the rear, or a spare tire hanging down or missing.
- Why it happens
- A link in the steel chain that holds the spare tire under the vehicle may not have been welded properly and can break.
- What to do
- Check your VIN for recall 23V-468. The dealer replaces the spare tire carrier for free.
Oxygen sensor heater failures
- What you'll notice
- Check engine light, often with code P0051 or a similar oxygen sensor heater code. Some owners also notice rough idle or lower fuel economy.
- Why it happens
- The heater circuit inside the oxygen sensors burns out. Early Sequoias are known for repeat oxygen sensor failures.
- What to do
- Have the code read to see which sensor is at fault, then replace that sensor. Lean codes like P0171 or P0174 point to a different problem and should be diagnosed separately.
Tow hitch cover can fall off (recall)
- What you'll notice
- The plastic cover over the hitch opening in the rear bumper rattles, works loose, or is missing.
- Why it happens
- The clips that hold the cover in the bumper do not lock in securely, so it can shake loose while driving and become a hazard for drivers behind you.
- What to do
- Check your VIN for recall 24V-640. The dealer installs an improved cover and modifies the bumper for free.
Load capacity label may show the wrong weight (recall)
- What you'll notice
- No symptoms. The sticker in the door jamb that tells you how much weight you can carry may list the wrong numbers.
- Why it happens
- The label added for dealer-installed accessories may not show the correct added weight, which could lead an owner to overload the SUV.
- What to do
- Check your VIN for recall 26V-179. The dealer replaces the label for free. Until then, avoid loading the SUV close to its limit.
Repair prices for your Toyota Sequoia
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Frame rust treatment or frame repair
- Replace one exhaust manifold and gaskets
- Replace one oxygen sensor
- Replace one secondary air injection pump
- Replace yaw rate (deceleration) sensor
- Replace front brake pads (and rotors if worn)
- Replace water pump and refill coolant
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Inspect and replace front lower ball joints under recallNo charge if your vehicle is included
- Replace passenger airbag inflatorNo charge if your vehicle is included
- Reprogram skid control ECUNo charge if your vehicle is included
- Reprogram airbag control moduleNo charge if your vehicle is included
- Install seat heater wiring protection or replace heaterNo charge if your vehicle is included
- Replace power steering gear assemblyNo charge if your vehicle is included
- Install pedal reinforcement or replace pedalNo charge if your vehicle is included
- Grease or replace power window master switchNo charge if your vehicle is included
- Replace low-pressure fuel pumpNo charge if your vehicle is included
- Update airbag control unit softwareNo charge if your vehicle is included
- Update transmission control softwareNo charge if your vehicle is included
- Update multimedia display softwareNo charge if your vehicle is included
- Replace hitch cover and modify bumperNo charge if your vehicle is included
- Replace spare tire carrierNo charge if your vehicle is included
- Inspect and replace affected tiresNo charge if your vehicle is included
- Replace load capacity labelNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.