Your 2011 Volkswagen Routanproblems, repair costs and recalls
What we've documented about the 2011 Volkswagen Routan: problems owners and shops report, typical repair and upkeep costs, and safety recalls.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems for your 2011 Volkswagen Routan
15 documented issues apply to 2011, most serious first.
Power module (TIPM) failure: no-start, stalling or fuel pump that won't shut off
- What you'll notice
- The van cranks but won't start, stalls while driving, or the fuel pump keeps running after the van is off and drains the battery. Some owners also see random warning lights or weak electrical systems.
- Why it happens
- The Routan uses Chrysler's under-hood power module (TIPM). Its built-in fuel pump relay and circuits are known to fail on these minivans.
- What to do
- Have a shop test fuel pump power and the TIPM before replacing the pump, battery or alternator. A repaired or replaced TIPM, or a fix for its fuel pump relay, is usually the cure.
Harsh shifting, stuck in gear or transmission failure
- What you'll notice
- Rough or delayed shifts, harsh downshifts when slowing down, the van stuck in one gear (limp mode), or a transmission that stops shifting altogether.
- Why it happens
- The 6-speed automatic in these vans can wear internally, and its valve body, speed sensors, solenoids and control software are frequent trouble spots. Some cases were improved by a software update.
- What to do
- Check the fluid and have the codes read at the first sign of trouble. Ask about software updates; a sensor or solenoid fix is much cheaper than a full replacement if caught early.
Left cylinder head failure and misfires
- What you'll notice
- Check engine light, a ticking noise from the engine, rough running or misfires, and loss of power.
- Why it happens
- Early 3.6L V6 engines could overheat valve seats in the left cylinder head (cylinder 2). Chrysler extended coverage on the left head to 10 years or 150,000 miles for many 2011-2013 engines.
- What to do
- Get the misfire codes read. If cylinder 2 keeps misfiring, ask a Volkswagen or Chrysler dealer whether your van's engine falls under the extended head coverage.
Network (CAN bus) faults cause many warning lights
- What you'll notice
- Several warning lights come on at once, gauges act up, wipers or lights turn on by themselves, or the door locks stop working.
- Why it happens
- Wiring or module faults on the van's data network (CAN bus) stop modules from talking to each other. Tracking the fault down can take a lot of time.
- What to do
- Have a shop scan all modules, not just the engine. Check the battery and grounds first, since low voltage can trigger network faults.
Ticking from worn rocker arms
- What you'll notice
- A ticking or tapping noise from the top of the engine, sometimes with a check engine light for a misfire.
- Why it happens
- The roller rocker arms (cam followers) on the 3.6L V6 can wear or seize their rollers, which damages the camshaft if left alone.
- What to do
- Have it checked soon; replacing rocker arms early avoids a much bigger camshaft repair. Many shops replace all of them at once.
Oil filter housing and cooler leak
- What you'll notice
- Oil spots under the front of the van, a burning oil smell, or oil and coolant mixing. The leak can come and go, which makes it hard to find.
- Why it happens
- The 3.6L V6 has a plastic oil filter housing with a built-in oil cooler that cracks or leaks at its gaskets with age and heat.
- What to do
- Have the top of the engine inspected for oil around the filter housing. The housing sits under the intake manifold, so most of the bill is labor.
Power sliding door hinge breaks or door sticks
- What you'll notice
- A sliding door grinds, sticks, won't close on its own, reverses while closing, or rubs the body paint. Some doors hang loose from a broken hinge.
- Why it happens
- The lower hinge and roller track wear and break, and the door module can be overly sensitive. Volkswagen issued fixes including hinge replacement and reprogramming.
- What to do
- Have the hinge, track and door module checked. Lubricating the track helps, but a broken hinge should be replaced before it damages the door.
Brakes wear out early and rotors warp
- What you'll notice
- Steering wheel shake or pedal pulsing when braking, squealing, and pads that need replacing much sooner than expected.
- Why it happens
- The brakes on these heavy vans run hot and the rotors warp easily, which also wears pads quickly.
- What to do
- Have pads and rotors measured. Quality rotors and pads, and not riding the brakes on hills, help them last longer.
Sticking brake calipers
- What you'll notice
- The van pulls to one side, one wheel gets very hot, a grinding noise from one corner, or brake pads that wear unevenly.
- Why it happens
- Caliper pistons and slide pins corrode and stick, so a brake keeps dragging. Rear calipers and the parking brake cable are often involved.
- What to do
- Have the brakes inspected soon; a dragging caliper ruins pads and rotors and can overheat the brakes.
A/C blows warm from leaks or compressor failure
- What you'll notice
- The A/C blows warm, especially from the rear vents, or works only now and then.
- Why it happens
- Refrigerant leaks at the rear A/C lines and rear evaporator are common on these vans, and compressors fail too.
- What to do
- Have the system leak-tested with dye before recharging. Recharging without fixing the leak just wastes money.
Alternator failure and battery light
- What you'll notice
- The battery light comes on, the lights dim, and the van may die while driving or not restart.
- Why it happens
- Alternators on the 3.6L V6 Routan fail with some regularity. A loose or worn serpentine belt or tensioner can also stop the battery from charging.
- What to do
- Have the charging system tested right away. Check the belt and tensioner too when replacing the alternator.
Worn wheel bearings
- What you'll notice
- A humming or growling noise that gets louder with speed and may change when turning.
- Why it happens
- Front and rear wheel bearings wear out on these heavy vans. A Chrysler bulletin covered front bearings on some vans.
- What to do
- Have the bearings checked. A badly worn bearing can overheat and become unsafe, so don't put it off.
Tire pressure sensors fail or light flickers
- What you'll notice
- The tire pressure light comes on or flickers even when tires are fine, or a sensor stops reading.
- Why it happens
- The tire pressure sensors corrode at the valve stems and their batteries wear out with age.
- What to do
- Check the tires with a gauge first. Failed sensors can be replaced one at a time and need to be relearned.
Moan or hum on cold starts
- What you'll notice
- A moan, whistle or loud hum right after starting on cold mornings that fades as the van warms up.
- Why it happens
- Owners trace this to the power steering and engine accessories on the 3.6L vans; a Chrysler service bulletin addressed it on some vans.
- What to do
- Mention it to the dealer and ask about the related bulletin. It's mostly an annoyance, but have fluid levels checked.
Sunroof and liftgate water leaks
- What you'll notice
- Water inside the cabin, wet headliner or damp cargo area after rain.
- Why it happens
- Sunroof seals and the liftgate's upper seal can leak, and clogged drains make it worse.
- What to do
- Clear the sunroof drains and check the seals. A body shop can reseal the liftgate gasket.
Repair prices for your 2011 Volkswagen Routan
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace or repair TIPM power module
- Repair valve body/sensors or replace automatic transmission
- Replace left cylinder head
- Replace rocker arms and lash adjusters
- Replace oil filter housing/cooler assembly
- Replace sliding door lower hinge/track or door motor
- Front brake pads and rotors
- Replace brake caliper
- Diagnose and repair CAN bus wiring or module
- Repair refrigerant leak or replace A/C compressor
- Replace alternator
- Replace wheel bearing/hub assembly (one wheel)
- Replace TPMS sensor and relearn
- Clear drains and reseal sunroof or liftgate
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Checking the NHTSA recall database…