Home › Warning lights › Glow plug light (diesel)
Amber/yellow: check soon

Glow plug light (diesel)

Also called: Coil light, Pre-heat light

How urgent? Check it when you can

What it means

On a diesel, the glow plugs are warming the engine before starting. If it flashes or stays on while driving, there's an engine fault.

An amber symbol in the cluster that looks like a coiled spring or a squiggly hot wire, usually drawn between two short upright lines. Diesel trucks from Ford, Ram and GM often skip the symbol and spell out WAIT TO START or WAIT instead. On VW, Mercedes and other European diesels it is the curly coil, and it sits near the other engine lights.

Can I keep driving?

Wait for it to go out before starting. If it flashes while driving, get it checked soon.

If it's flashing or blinking: A steady light right after you switch the ignition on is normal pre-heating - it goes out in a few seconds, or up to fifteen or twenty seconds on a freezing morning. A light that flashes, or one that stays on after the engine is running and warm, is a fault. On many European diesels the flashing version also means the engine has dropped into a reduced power mode to protect itself.

What to do now

  1. Wait for the light to go out, then start.
  2. If hard starting in the cold, have the glow plugs tested.

Common causes

  • Normal pre-heat
  • Failed glow plug or relay
  • Engine fault on some diesels

Checks you can do yourself

Safe, no tools in most cases

Do these with the car parked and the engine off and cool. If anything looks or smells hot, wait.

1
Let the pre-heat finish before you crank

Turn the key to on, or press the start button once without starting on a push-button diesel, and wait for the coil symbol to go out before you crank. In cold weather that can take fifteen or twenty seconds. Cranking before the light goes out is the number one cause of hard cold starting on a healthy diesel.

1 minute · None
2
Write down exactly what the engine does

Note whether the light is steady or flashing, whether it only misbehaves when the engine is stone cold, how many seconds you have to crank, and whether you get white or grey smoke out the tailpipe for the first minute. A shop can narrow this down in half the time with those four answers, because no single symptom proves a glow plug on its own.

5 minutes · None
3
Check the battery terminals and have the battery tested

With the engine off and cold, look at the posts on top of the battery or batteries - diesels often have two. You want clean metal and clamps that will not move when you nudge them. White or blue fluff means a poor connection. Most parts stores will test a battery free in the parking lot, and a tired battery makes a glow plug problem look far worse than it is.

15 minutes · None
4
Read the owner's manual page for this light

Look up the coil symbol or the WAIT TO START message in the index of your manual. Makes do not agree on what the flashing version means - on some it is only the glow plugs, on others the same lamp flashes for a general engine fault. Two minutes in the manual tells you which kind of car you have, and whether it says to limit how you drive.

5 minutes · None

Step-by-step repair walkthroughs for the fixes below are on the way.

What not to do

  • Don't crank for more than about ten seconds at a stretch - a diesel starter gets very hot. Wait a minute between tries.
  • Don't spray starting fluid or ether into a glow-plug diesel; it can crack a piston or bend a rod.
  • Don't tow or haul with the light flashing - on many diesels the flash means the engine has already cut its own power.
  • Don't just clear the code; the light comes back on the next cold start, because the computer retests the plugs every time.

What it usually turns out to be

Most likely first. Prices are typical US parts-and-labor totals for that repair, not a quote for your vehicle.

One or more burned out glow plugsPrice not verified

How you can tell Hard starting when the engine has sat overnight, fine once it is warm, often with white or grey smoke and a rough shaky idle for the first half a minute. Usually stores a code naming the circuit, such as a glow plug circuit fault on cylinder two.

The repair The bad plugs are replaced, and most shops do the whole set at once because they all have the same age on them. Cost swings a lot with how buried the plugs are, and a plug seized into the head can double the labor.

Failed glow plug relay or control modulePrice not verified

How you can tell All of the plugs test fine but none of them ever heat up, so the engine is hard to start in cold weather every single time rather than now and then. Sometimes you can hear a click missing when the key goes on. Stores a control circuit code rather than one naming a cylinder.

The repair The relay or the small control box that feeds the plugs is replaced. It is often an easy part to reach, which keeps the labor down. Relays fail more often than the plugs themselves on some engines.

Corroded wiring or bus bar at the plugsPrice not verified

How you can tell The fault comes and goes, or only shows up after wet weather or a winter of road salt. One or two cylinders are reported as open while the rest are normal, and the trouble often moves between cylinders over time.

The repair The harness, connectors or the metal strip that links the plugs is cleaned up or replaced. On some engines this means getting past the intake to reach it.

Blown glow plug fuse or fusible linkPrice not verified

How you can tell The symptom arrives suddenly and completely - the engine was fine yesterday and today it will not pre-heat at all. The scan reports the whole circuit as dead. A blown fuse is a symptom, so a good shop looks for what blew it.

The repair The fuse or link is replaced, and the circuit is tested to find whatever overloaded it, usually a shorted plug or a chafed wire.

Bad coolant or intake air temperature sensorPrice not verified

How you can tell The plugs and the module are all healthy, but the engine thinks it is already warm so it never runs a pre-heat cycle. The temperature gauge may read oddly, or the engine may also idle rough and use more fuel than usual.

The repair The sensor is replaced and the reading is checked against the real engine temperature on a scan tool.

An unrelated engine fault using the same lampPrice not verified

How you can tell Mostly European diesels. The light flashes while you drive, the engine feels flat or down on power, and there is nothing at all wrong with the plugs. The stored code points somewhere else entirely, such as the exhaust gas valve or a pressure sensor.

The repair Whatever the stored code points at gets repaired. Cost depends entirely on the real fault, which is why a scan comes before any parts.

What a shop will do

A shop reads the codes first, because the code usually says whether the problem is one cylinder or the whole circuit. Then, with the engine off, they measure each plug and watch how much current the system pulls when the key goes on - a dead plug draws nothing and a shorted one draws far too much. They also check power and ground at the relay or control box, and the battery, since weak batteries fake this fault. Allow about an hour, more on engines where the plugs sit under the intake.

How to reset this light

There is nothing here you are meant to reset. The steady light at key-on is the system working, and it goes out by itself. The flashing or stay-on version is a fault, and clearing the code only hides it - the computer tests the plugs again on the next cold start, so the light is back within a day or two. Fix the plug, relay or wiring and the light goes out on its own.

Some diesels keep the fault stored until the engine has been through a cold start, so the light may take a day to clear after a correct repair.

Trouble codes often stored with this light

Common questions

What does the glow plug light (diesel) mean?

On a diesel, the glow plugs are warming the engine before starting. If it flashes or stays on while driving, there's an engine fault.

Can I drive with the glow plug light (diesel) on?

Wait for it to go out before starting. If it flashes while driving, get it checked soon.

Can I drive with the glow plug light on?

If the engine starts and runs smoothly, short local trips are usually fine, and the car will often behave normally once it is warm. Expect hard starting on cold mornings and a rough first minute. If the light is flashing, the engine feels down on power, or you get heavy white smoke, get it looked at before you drive much further.

Why does it only cause trouble in cold weather?

Glow plugs are only there to pre-warm the cylinders so diesel will light off when the engine is cold. Once the engine is warm it does not need them at all, which is why a car with dead plugs starts fine all summer and then refuses on the first frosty morning.

Do I have to replace all the glow plugs at once?

You do not have to, but most shops will, and it is usually the cheaper choice overall. The plugs have all done the same mileage, so the others are close behind, and nearly all the cost is the labor of getting to them. Doing one at a time means paying that labor again in a year.

Will a glow plug light fail an emissions test?

The light itself is not what testers look at. The problem is that a glow plug fault usually also sets a check engine light, and in states that plug into the computer a stored engine code fails the test. A diesel that smokes heavily on a cold start can also fail a visual or opacity check.

Can a bad glow plug damage the engine?

Not quickly, but it is not harmless either. Long cranking wears the starter and battery, and unburnt diesel washing past the rings dilutes the oil and can wear the engine over time. The worse risk is a plug tip breaking off inside a cylinder, which turns a modest job into a very expensive one.

Sources: YourMechanic · Mechanic Base · Stoneacre

Symbols vary a little between makes. Your owner's manual shows the exact lights for your vehicle. This is a general guide, not a diagnosis.