Home › Symptom guides › Car won't go into gear
Driving & handling

Why won't my car go into gear or move?

When a car won't go into gear, the big clues are whether the shifter moves, whether the engine revs without the car moving, and whether you have an automatic or a manual. Some causes are simple, like a shift lock or a parking brake left on. Others, like a transmission that has lost its fluid, mean the car shouldn't be driven. Answer a few questions to find out which.

Stop and get help right away if:
  • Before getting out, set the parking brake firmly. If the shifter or transmission is faulty, the car may not really be in Park.
  • If you smell burning or see smoke from under the car, turn the engine off and step away.
  • Don't keep revving the engine to force it to move. That can turn a repairable problem into a ruined transmission or clutch.
Question 1

Is your car an automatic or a manual (stick shift)?

If there are only two pedals, gas and brake, it's an automatic. A manual has a third pedal, the clutch.

Full guide: every possible outcome

Prefer to read it all? Here's every result this guide can reach.

The shift lock may be holding the shifter in ParkSafe to check yourself first

What to do now: With the key in ON or the engine running, press the brake pedal firmly and try again. If it still won't move, use the shift lock release, a small slot or button near the shifter (your owner's manual shows where).

Why: Automatic cars won't let you leave Park unless they sense your foot on the brake. If that signal doesn't arrive, a small lock keeps the shifter in place. The cause is often simple and electrical rather than a transmission failure, but a shop can confirm it with a quick test.

Possible causes: Faulty brake light switch or blown fuse; Weak or dead battery; Car's weight resting on the Park lock; Failed shift lock part or shift cable.

A shop will usually test: Brake light switch test; Shift lock (interlock) check; Battery test.

A delay before it engages often points to low fluid or internal transmission wearGet it checked in the next few days

What to do now: Have the transmission checked within the next few days. If your car has a transmission dipstick, check the fluid level the way your owner's manual describes first.

Why: An automatic transmission uses fluid pressure to engage each gear. When the fluid is low or worn, or internal seals are tired, it can take longer to build that pressure. A shop will usually check the fluid and codes before deciding on any repair, and catching it early often means a smaller one.

Possible causes: Low transmission fluid; Old or burnt fluid; Worn internal seals or valve body problem; Transmission control fault.

A shop will usually test: Transmission fluid level and condition check; Code scan for transmission codes; Line pressure test.

The transmission may have lost one or more of its gearsStop — don't drive it

What to do now: Don't drive it. Have it towed to a transmission shop or a general repair shop.

Why: Drive and Reverse use different clutches or bands inside the transmission. When one direction works and the other doesn't, one of those may have failed or isn't getting enough fluid pressure. A car that can't be relied on to go forward isn't safe in traffic, and forcing it can cause more damage.

Possible causes: Low transmission fluid; Worn or failed clutch pack or band inside the transmission; Shift solenoid or valve body fault.

A shop will usually test: Fluid level and condition check; Code scan; Transmission pressure test; Internal inspection if needed.

The parking brake or a stuck brake may be holding the car backGet it checked in the next few days

What to do now: Make sure the parking brake is fully released (pedal, lever or electronic switch), then try moving off gently. If the car still feels held back, don't keep driving it. Have the brakes checked first.

Why: If you can feel the transmission go into gear but the car struggles to roll, something is resisting the wheels. A parking brake that's on, partly on or frozen, or a brake caliper that won't release, are common causes. A brake that stays on can overheat, so it shouldn't be driven on.

Possible causes: Parking brake still on or partly on; Parking brake frozen or rusted; Stuck brake caliper.

A shop will usually test: Brake inspection; Parking brake cable and mechanism check; Caliper release check.

The shifter may have come disconnected from the transmissionStop — don't drive it

What to do now: Set the parking brake firmly and don't drive it. Have it towed or have a mobile mechanic come to you.

Why: A cable or rod connects the shifter to the transmission. If it breaks, or the small bushing that holds it falls apart, moving the shifter no longer changes gears, so the transmission can be left in any gear, including one that lets the car roll. It's often a small part, but the car isn't safe to use until it's checked and fixed.

Possible causes: Worn-out shift cable bushing; Broken, stretched or disconnected shift cable or linkage; Linkage not reconnected after a repair.

A shop will usually test: Shift cable and bushing inspection; Shift linkage adjustment check; Gear position (range) sensor check.

The transmission may have lost its fluidStop — don't drive it

What to do now: Don't drive it. Have it towed so the leak can be found and fixed before more damage is done.

Why: An automatic transmission needs fluid pressure to engage any gear. A large leak, like a split cooler line or a damaged pan, can drain it quickly, and the car stops moving. Running it with too little fluid, even briefly, can ruin the transmission. A shop will find the leak and check for damage before refilling and road-testing.

Possible causes: Leaking transmission cooler line; Leaking pan, gasket, seal or drain plug; Leaking axle seal.

A shop will usually test: Leak inspection; Refill and pressure test; Check for damage from running low.

An axle or drive shaft may be brokenStop — don't drive it

What to do now: Don't drive it. Have it towed, ideally on a flatbed truck.

Why: A loud bang or clunk followed by no movement often means something between the transmission and the wheels has snapped. The engine and transmission may be fine, but the power isn't reaching the wheels. Clicking when turning in the days before often points to a worn CV joint. A shop will inspect the axles, drive shaft and differential to confirm.

Possible causes: Broken CV axle; Broken drive shaft or U-joint; Broken parts inside the differential or transmission.

A shop will usually test: Axle and CV joint inspection; Drive shaft and U-joint check; Differential inspection.

The transmission doesn't seem to be sending power to the wheelsStop — don't drive it

What to do now: Don't drive it. Have it towed to a shop and ask for a transmission diagnosis.

Why: When the gear display shows Drive and the engine revs but the car doesn't move, the transmission isn't engaging. Possible reasons include very low fluid, worn internal clutches, a failed torque converter or pump, or an electronic fault. A shop will usually check the fluid, codes and pressure before deciding what has failed. Revving it harder won't help and can cause more damage.

Possible causes: Very low transmission fluid; Worn internal clutches; Failed torque converter or transmission pump; Electronic control fault.

A shop will usually test: Fluid level and condition check; Code scan; Line pressure test; Torque converter and pump check.

The clutch hydraulics may have failedStop — don't drive it

What to do now: Don't drive it. Check the clutch fluid reservoir and look for leaks, then have it towed or call a mobile mechanic to the car.

Why: Most manual cars use fluid pressure to release the clutch. If the pedal sinks or stays down, that pressure may be gone, so the clutch can't release and gears grind or won't go in. Forcing it into gear risks damaging the transmission and leaves you without control of when the car moves.

Possible causes: Leaking clutch slave cylinder; Failed clutch master cylinder; Air in the clutch line; Broken clutch cable.

A shop will usually test: Clutch hydraulic inspection; Clutch master and slave cylinder test; Clutch system bleed.

The clutch may not be fully releasingGet it checked in the next few days

What to do now: Press the clutch all the way to the floor and wait two or three seconds before selecting first or Reverse, and book a clutch check in the next few days.

Why: Gears go in smoothly only when the clutch fully disconnects the engine from the transmission. If it doesn't fully release, parts inside are still spinning and the gears clash. Low fluid, air in the line or a worn clutch are common reasons, and a shop will usually check the hydraulics before looking at the clutch itself.

Possible causes: Low clutch fluid or air in the line; Worn or warped clutch parts; Worn synchros in the transmission.

A shop will usually test: Clutch release check; Clutch hydraulic inspection; Transmission inspection for worn synchros.

The clutch may be slipping badlyStop — don't drive it

What to do now: Don't drive it. Have it towed to a shop.

Why: When the gear goes in but the engine revs without moving the car, the clutch may no longer be gripping. That usually builds gradually as the clutch wears, then suddenly gets much worse. Oil on the clutch, or a hydraulic problem keeping it partly released, can do the same, so a shop will check those before replacing the clutch.

Possible causes: Worn-out clutch disc; Clutch hydraulics not letting it fully engage; Oil leaking onto the clutch; Broken axle or drive shaft.

A shop will usually test: Clutch slip test; Clutch hydraulic check; Axle and drive shaft inspection.

A shop needs to see what's stopping it from movingBook a check when convenient

What to do now: Set the parking brake, note what you see and hear when you try to shift, and have it towed or call roadside assistance.

Why: Without knowing whether the shifter moves, whether the engine revs, or whether there's a leak, it's hard to narrow it down safely. A technician can quickly tell a shifter problem from a fluid, clutch or axle problem.

Possible causes: Shifter or shift lock problem; Low fluid or a transmission fault; Clutch or axle problem.

A shop will usually test: Shift linkage check; Fluid level check; Code scan; Drive line inspection.

Related guides

Sources and references: National Highway Traffic Safety Administration (NHTSA)

This guide helps you understand what may be going on and how urgent it is. It doesn't replace an in-person inspection.