Chrysler Pacificaproblems, repair costs and recalls
Problems reported across 2004–2026. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
35 documented issues across all years, most serious first.
Engine cradle (subframe) rusting through
- What you'll notice
- Clunks from under the front of the vehicle, an engine that seems to shift, or a shop pointing out heavy rust or holes in the front subframe during an oil change or inspection. Some vans fail state safety inspection because of it.
- Why it happens
- The front subframe that carries the engine and front suspension was not given enough rust-proof coating at the factory. In salted-road areas it can rot through, and in bad cases the engine and suspension mounting points lose their strength.
- What to do
- Have the subframe inspected on a lift, especially on 2004-2005 vans from snowy states. If there are holes or flaking metal at the mounts, stop using the van for long trips until the cradle is replaced.
Integrated power module (TIPM) failure
- What you'll notice
- Stalling, headlights or dash lights going out, wipers or radio cutting out (often in rain), ABS and stability lights flickering on, or a no-start with just a click.
- Why it happens
- The totally integrated power module is the under-hood fuse and relay box that also has its own circuit board. When it fails, it can cut power to the fuel pump and many other circuits at random.
- What to do
- If several unrelated electrical things act up at once, ask the shop to test the TIPM before replacing individual parts. A replacement module must be programmed to the van.
Engine stalls while driving
- What you'll notice
- The engine cuts out while driving or at a stop, sometimes with the dash lights flickering first. It often restarts, and dealers frequently find no stored code.
- Why it happens
- Owners and shops have traced it to several causes: a corroded engine ground wire (the G103 ground bolted to the engine), a sticking EGR valve, a failing TIPM, or a weak crank sensor.
- What to do
- Note when it happens and whether any lights flicker. Ask the shop to check the engine ground connections and the EGR valve first, since those are cheap fixes.
Automatic transmission limp mode, slipping or shudder
- What you'll notice
- The van gets stuck in one gear (limp mode), won't shift into 4th, slips, or shudders and vibrates at 30-40 mph.
- Why it happens
- The four-speed automatic in these vans can suffer from solenoid pack faults, leaking solenoid gaskets and a worn torque converter. A burst cooler hose can also drain the fluid.
- What to do
- Check the fluid level and look for leaks. Have the codes read; a solenoid pack or torque converter repair costs much less than a full transmission if caught early.
AWD transfer case (power transfer unit) failure
- What you'll notice
- Loud grinding or whining from the front of the van, smoke or a burning smell, and fluid leaks near the transmission on all-wheel-drive models.
- Why it happens
- The power transfer unit that sends power to the rear wheels on AWD Pacificas can wear out or crack its housing. Some owners blame worn engine mounts that let the drivetrain move too much.
- What to do
- Stop driving if you hear grinding with smoke. Have the transfer unit fluid and housing checked; replacement parts can be back-ordered, so get a quote early.
Fuel supply tube can separate and leak (recall)
- What you'll notice
- A strong gasoline smell or fuel dripping under the hood.
- Why it happens
- Some 2004 Pacificas were built with a fuel supply tube that was not made correctly and can pull apart, leaking fuel near hot engine parts.
- What to do
- If you smell fuel, park outside and do not drive. Check the VIN for recall 03V471; the dealer fix is free.
Done free by a Chrysler dealer under recall 03V-471.
Engine computer software can stall the engine (recall)
- What you'll notice
- The engine stalls without warning while driving.
- Why it happens
- A self-test for the EGR system in the engine computer software on some 2004 vans could make the engine stall.
- What to do
- Check the VIN for recall 04V113. The dealer reprograms the engine computer for free.
Done free by a Chrysler dealer under recall 04V-113.
Halogen headlights can cut out (recall)
- What you'll notice
- One or both headlights flicker or go out while driving, at first now and then and later for good.
- Why it happens
- On some 2005 vans with halogen headlamps, a fault in the headlamp circuit can make the low beams stop working.
- What to do
- Check the VIN for recall 05V066 and have it done for free. Avoid night driving if the headlights flicker.
Done free by a Chrysler dealer under recall 05V-066.
Fuel pump module and engine software can stall the engine (recall)
- What you'll notice
- The engine dies while driving with no warning, sometimes after the fuel level runs low.
- Why it happens
- Under some conditions the fuel pump module and the engine computer software can combine to starve the engine and stall it.
- What to do
- Check the VIN for recall 06V432. The dealer updates the software and fuel pump parts for free.
Done free by a Chrysler dealer under recall 06V-432.
Harsh shifting, jerking or slipping from the 9-speed automatic
- What you'll notice
- Hard bangs or jerks when shifting at low speed, slipping with the engine revving before a gear catches, clunks into reverse or drive, or a Service Transmission message.
- Why it happens
- The nine-speed automatic used with the gas engine is known for rough shift quality. Many cases are improved with software updates and a shift relearn; some vans need a valve body or a new transmission. Most reports involve 2017-2018 vans.
- What to do
- Ask the dealer to check for transmission software updates and do an adaptive relearn first. If it slips or flashes Service Transmission, have it checked right away, ideally while still under warranty.
Hybrid battery can catch fire while parked (recall)
- What you'll notice
- Usually no warning. Some vans show a hybrid system warning before an event.
- Why it happens
- The high-voltage battery in some 2017-2018 Pacifica Hybrids can short internally and start a fire even when the van is off and not charging.
- What to do
- Check your VIN for recall 22V077 (replaced by 24V538). Until it is fixed, follow Chrysler's advice: don't charge it and park outside, away from buildings.
Done free by a Chrysler dealer under recall 24V-538.
Hybrid battery pack fire risk on 2020-2022 (recall)
- What you'll notice
- Usually no warning before a fire.
- Why it happens
- The high-voltage battery pack in some 2020-2022 Pacifica plug-in hybrids can catch fire, even when parked with the ignition off.
- What to do
- Check the VIN for recall 26V362. Don't charge the van and park it outside, away from buildings, until the remedy is done.
Done free by a Chrysler dealer under recall 26V-362.
Hybrid inverter can fail and stop the van (recall)
- What you'll notice
- Sudden loss of drive power with a hybrid system warning; the van coasts and won't move under its own power.
- Why it happens
- Diodes inside the power inverter module can be damaged by a voltage spike and shut down the drive system.
- What to do
- Check the VIN for recall 17V371 and have the free repair done.
Done free by a Chrysler dealer under recall 17V-371.
Gas engine may not restart properly after electric driving (recall)
- What you'll notice
- Loss of power when the engine should start, a check engine light, or a hot smell from the exhaust.
- Why it happens
- After running on battery power, the gas engine may not restart correctly. Unburned fuel can then reach the catalytic converter and overheat it, with a small fire risk.
- What to do
- Check the VIN for recall 18V740 and have the software updated for free.
Done free by a Chrysler dealer under recall 18V-740.
12-volt battery isolator post can overheat (recall)
- What you'll notice
- A burning plastic smell near the driver seat area, electrical warnings, or no-start.
- Why it happens
- On plug-in hybrids the 12-volt isolator post under the driver area can develop high resistance and overheat, which can start a fire.
- What to do
- Check the VIN for recall 20V334 and have the free fix done.
Done free by a Chrysler dealer under recall 20V-334.
Transmission wiring connector can shut off the engine (hybrid recall)
- What you'll notice
- The engine shuts off unexpectedly and the van may lose drive power, often with warning lights.
- Why it happens
- A wiring connector inside the hybrid transmission can short circuit and shut the engine down.
- What to do
- Check the VIN for recall 23V010 and have the dealer repair it for free.
Done free by a Chrysler dealer under recall 23V-010.
Engine software can lose crank sensor timing and stall (recall)
- What you'll notice
- The engine stalls while driving and may restart.
- Why it happens
- The engine control software can lose sync with the crankshaft position sensor signal on the 3.6L gas engine, which shuts the engine off.
- What to do
- Check the VIN for recall 18V049. The software update is free.
Done free by a Chrysler dealer under recall 18V-049.
Engine computer power chip can fail and stall the van (recall)
- What you'll notice
- Sudden stall while driving or a no-start, sometimes with several warning lights.
- Why it happens
- A voltage regulator chip in the powertrain control module can fail, shutting the engine off or preventing it from starting.
- What to do
- Check the VIN for recall 18V524 and have the free repair done.
Done free by a Chrysler dealer under recall 18V-524.
Loose battery ground can cut power steering and stall the engine (recall)
- What you'll notice
- Steering suddenly feels very heavy, the engine stalls at a stop, or the stop/start system acts up.
- Why it happens
- On gas vans with engine stop/start, the battery ground connection can loosen, causing intermittent loss of power steering assist or a stall.
- What to do
- Check the VIN for recall 19V348. The dealer fixes the ground for free.
Done free by a Chrysler dealer under recall 19V-348.
Cruise control may not turn off (recall)
- What you'll notice
- Cruise control stays on and holds or increases speed even after you press the brake or switch it off.
- Why it happens
- A short circuit in the wiring can keep cruise control from canceling.
- What to do
- If it happens, shift to neutral and brake firmly. Check the VIN for recall 18V332; the software update is free.
Done free by a Chrysler dealer under recall 18V-332.
Badly welded transmission part can cause loss of drive (recall)
- What you'll notice
- The van suddenly loses power to the wheels while driving.
- Why it happens
- A part inside the nine-speed transmission on some 2018 gas vans may have a poor weld that can break.
- What to do
- Check the VIN for recall 18V492 and have it inspected and repaired for free.
Done free by a Chrysler dealer under recall 18V-492.
Right front lower control arm can separate (recall)
- What you'll notice
- Clunking from the right front, the van pulling, or sudden loss of steering control.
- Why it happens
- On some 2018 Pacificas the right front lower control arm may come apart from the steering knuckle.
- What to do
- Check the VIN for recall 19V143 and have it repaired for free. Don't drive if the front end clunks badly or the wheel looks out of line.
Done free by a Chrysler dealer under recall 19V-143.
Front axle shaft can come apart (recall)
- What you'll notice
- Clicking or clunking, then loss of drive, or the van rolling even when in Park.
- Why it happens
- Front half-shafts on some 2018 Pacificas were assembled wrong and can pull out of the CV joint.
- What to do
- Use the parking brake every time you park. Check the VIN for recall 18V493.
Done free by a Chrysler dealer under recall 18V-493.
Side curtain airbag connector may be loose (recall)
- What you'll notice
- Possibly an airbag warning light, but often no sign at all.
- Why it happens
- A side curtain airbag connector may not be fully seated, so the curtain airbag might not deploy in a crash.
- What to do
- Check the VIN for recall 24V793; the dealer secures the connector for free.
Done free by a Chrysler dealer under recall 24V-793.
Side curtain airbags may not hold pressure (recall)
- What you'll notice
- No warning to the driver.
- Why it happens
- Seams in the side curtain airbags may not be sealed well enough, so the airbags may deflate too soon in a crash or rollover.
- What to do
- Check the VIN for recall 26V189 (which replaces 25V302 and 25V573) and get the free fix when parts are available.
Done free by a Chrysler dealer under recall 26V-189.
Second-row seat latch can stick open (recall)
- What you'll notice
- The second-row seat rattles or doesn't feel locked to the floor.
- Why it happens
- The latch that holds the second-row seat to the floor can stick open, so the seat may not be secured in a crash.
- What to do
- Push and pull on the seat after moving it to be sure it's locked. Check the VIN for recall 22V181.
Done free by a Chrysler dealer under recall 22V-181.
Steering column module weld can stop the driver airbag (recall)
- What you'll notice
- Possibly an airbag warning light.
- Why it happens
- A poorly welded part in the steering column control module can break the circuit to the driver airbag.
- What to do
- Check the VIN for recall 24V199 and have it replaced for free.
Done free by a Chrysler dealer under recall 24V-199.
Brake pedal sensor can disable stability control (recall)
- What you'll notice
- Stability control or brake warning lights come on.
- Why it happens
- A capacitor in the brake pedal position sensor can crack, causing loss of electronic stability control.
- What to do
- Check the VIN for recall 26V561 and have the sensor replaced for free.
Done free by a Chrysler dealer under recall 26V-561.
Front-end clunks from tie rods, sway bar links and control arm bushings
- What you'll notice
- Clunking or rattling over bumps, loose or wandering steering, uneven tire wear, or a knock when you start moving.
- Why it happens
- Tie rod ends, sway bar links and bushings, and front lower control arm bushings on this heavy crossover wear quickly. Early 2004s had especially weak control arm bushings, and some owners replaced tie rods more than once.
- What to do
- Have the front end inspected. Sway bar links are cheap; worn tie rods need prompt replacement and a wheel alignment because a broken one causes loss of steering.
Engine mounts tearing or leaking
- What you'll notice
- A heavy clunk when shifting into drive or reverse or when you step on the gas, more vibration at idle, and an engine that visibly rocks.
- Why it happens
- The fluid-filled engine mounts on the Pacifica tear and leak, and owners report replacing them more than once.
- What to do
- Have the mounts checked with the engine running and in gear. Replace broken mounts soon, because a loose engine strains hoses, wiring, ground straps and the transmission.
EGR valve sticking, rough idle and check engine light
- What you'll notice
- Check engine light (often code P0401 or P0404), rough or stumbling idle, hesitation, or stalling when coming to a stop.
- Why it happens
- The electrically driven exhaust gas recirculation (EGR) valve gets clogged with carbon and stops opening or closing correctly.
- What to do
- Have the codes read. Cleaning or replacing the EGR valve is usually an inexpensive fix that also cures some stalling complaints.
Radiator cracks and coolant leaks
- What you'll notice
- Coolant puddles under the front, a sweet smell, the temperature gauge rising, or the low coolant warning.
- Why it happens
- The plastic radiator tanks crack with age and heat cycles. Radiators and coolant hoses are among the most-replaced parts reported by Pacifica owners.
- What to do
- Top up with the correct coolant and have the system pressure-tested. Don't keep driving if it overheats.
Oil filter housing and oil cooler leak
- What you'll notice
- Oil spots under the van, burning oil smell, oil or coolant seeping at the top back of the engine valley, or coolant loss.
- Why it happens
- The Pentastar V6 uses a plastic oil filter housing with a built-in oil cooler. It can crack or its gaskets can leak oil and sometimes coolant.
- What to do
- Have the leak traced before it soaks the belts and starter. The housing is replaced as a unit, often with an updated part.
Ticking engine from worn rocker arms
- What you'll notice
- A ticking or tapping from the top of the engine, sometimes with a misfire or check engine light.
- Why it happens
- Rocker arm roller bearings on the Pentastar V6 can wear and seize, which also wears the camshaft lobe if left alone.
- What to do
- Have a shop listen to it and check for misfire codes. Fixing worn rockers early avoids a costly camshaft replacement.
Service Hybrid System warning or no-start (hybrid)
- What you'll notice
- A Service Hybrid System or Service Electric Vehicle System message, the van refusing to go into Ready mode, or loss of electric-only driving.
- Why it happens
- Faults in the plug-in hybrid system, from the 12-volt battery and isolator post to the high-voltage battery and power electronics, trigger this warning. Several recalls cover parts of this system.
- What to do
- Check for open recalls first. Hybrid parts carry a longer federal emissions warranty, so have a Chrysler dealer diagnose it before paying for repairs.
Repair prices for your Chrysler Pacifica
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace front engine cradle (subframe) and align
- Replace and program integrated power module (TIPM)
- Diagnose stalling; repair engine ground or replace EGR valve
- Replace solenoid pack or torque converter; replace transmission if worn out
- Replace AWD power transfer unit
- Replace worn tie rod ends and sway bar links, then align
- Replace engine mount(s)
- Replace EGR valve
- Replace radiator and refill coolant
- Software update and relearn; replace valve body or transmission if needed
- Replace oil filter housing and oil cooler assembly
- Replace rocker arms and lash adjusters, both banks
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Replace fuel supply tube (free recall repair)No charge if your vehicle is included
- Reprogram engine computer (free recall repair)No charge if your vehicle is included
- Repair headlamp circuit (free recall repair)No charge if your vehicle is included
- Update engine software and fuel pump module (free recall repair)No charge if your vehicle is included
- Hybrid battery inspection, software and battery repair (free recall repair)No charge if your vehicle is included
- Hybrid battery pack remedy (free recall repair)No charge if your vehicle is included
- Update or replace power inverter module (free recall repair)No charge if your vehicle is included
- Update hybrid control software (free recall repair)No charge if your vehicle is included
- Repair 12-volt isolator post (free recall repair)No charge if your vehicle is included
- Repair hybrid transmission wiring connector (free recall repair)No charge if your vehicle is included
- Update engine control software (free recall repair)No charge if your vehicle is included
- Replace powertrain control module (free recall repair)No charge if your vehicle is included
- Repair battery ground connection (free recall repair)No charge if your vehicle is included
- Update engine computer software (free recall repair)No charge if your vehicle is included
- Inspect and repair transmission (free recall repair)No charge if your vehicle is included
- Inspect and replace right front lower control arm (free recall repair)No charge if your vehicle is included
- Inspect and replace front half-shafts (free recall repair)No charge if your vehicle is included
- Secure side curtain airbag connector (free recall repair)No charge if your vehicle is included
- Replace side curtain airbags (free recall repair)No charge if your vehicle is included
- Repair second-row seat latch (free recall repair)No charge if your vehicle is included
- Replace steering column control module (free recall repair)No charge if your vehicle is included
- Replace brake pedal position sensor (free recall repair)No charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.