Dodge Magnumproblems, repair costs and recalls
Problems reported across 2005–2008. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
26 documented issues across all years, most serious first.
Oil sludge or coolant in the oil ruins the engine (2.7L)
- What you'll notice
- Knocking or ticking that gets worse, an oil pressure light, milky or very dark thick oil, coolant that keeps going down with no outside leak, and eventually an engine that seizes or won't restart.
- Why it happens
- The 2.7L V6 runs hot and holds little oil, so it is prone to sludge, especially when oil changes are stretched. Its water pump sits behind the timing chain, and when the pump's seal or gasket leaks, coolant goes straight into the oil and destroys the bearings.
- What to do
- Change the oil on time with the correct synthetic and watch the coolant level closely. If coolant drops with no visible leak or the oil looks milky, stop driving and have the water pump checked right away. If the engine is already knocking, get a second opinion before paying for repairs, since replacement is often the realistic fix.
Dropped valve seat destroys a cylinder (HEMI)
- What you'll notice
- A sudden misfire with a flashing check engine light, a loud metallic knock, loss of power, smoke from the exhaust, and in some cases the engine dying while you drive. The starter may spin unusually fast because a cylinder has lost compression.
- Why it happens
- The 5.7L HEMI uses valve seats pressed into its aluminum heads. If the head runs hot, often after a cooling problem, a seat can loosen and fall into the cylinder, smashing the valve, piston and cylinder wall.
- What to do
- Pull over and shut the engine off if it starts knocking hard; driving on it spreads the damage. Have a compression test done. Expect a cylinder head and possibly engine replacement, so get a written quote and compare a remanufactured engine with a repair.
Automatic transmission failure
- What you'll notice
- Whining from the transmission, then slipping, no reverse, or the car suddenly losing all drive and refusing to move, sometimes on the highway. Failures are reported anywhere from about 30,000 to over 180,000 miles.
- Why it happens
- The automatic transmissions in these cars wear out internally. Some owners also traced damage to coolant getting into the fluid through the transmission cooler in the radiator, or to failed speed sensors and control modules.
- What to do
- Check the transmission fluid; if it is pink and milky, coolant has mixed in and the radiator must be replaced along with the transmission repair. Have the codes read before agreeing to a rebuild, since a sensor can cause similar symptoms.
Engine stalls or cuts out while driving
- What you'll notice
- The engine suddenly shuts off in traffic, at a stop or even at highway speed, and steering becomes heavy. It may restart right away or only after sitting.
- Why it happens
- Owners and shops have traced it to failing crankshaft or camshaft position sensors, a faulty engine computer (PCM), or the fuel tank venting problem described separately. Often no single cause is confirmed.
- What to do
- Have the codes read as soon as possible after a stall, even if no light is on. Sensor replacement is cheap and is often tried first. Because stalling is a safety risk, avoid busy highways until it is found.
Takata air bag inflators can rupture (recall)
- What you'll notice
- Usually no symptom. The driver and passenger front air bags can explode with too much force in a crash and throw metal pieces into the cabin.
- Why it happens
- The Takata inflators break down after years of heat and humidity. Recalls 15V313 (driver) and 16V352 (passenger) cover these cars.
- What to do
- Ask the dealer to confirm the recall applies to your VIN and have the free replacement done right away if it is still open.
Free at a dealer under the recall.
Car may not hold in Park (recall)
- What you'll notice
- The shifter shows Park, but the car can roll because the park pawl does not lock the transmission.
- Why it happens
- A plug that holds the park pawl's anchor shaft may have been installed wrong, letting the shaft move. Recall 05V460 adds a retaining bracket.
- What to do
- Always use the parking brake, and have the free recall repair done if it is open.
Free at a dealer under the recall.
Loose battery cable can start a fire (recall)
- What you'll notice
- Possible burning smell, flickering electrical power or a no-start, though there may be no warning before a fire.
- Why it happens
- The battery cable nut at the firewall stud may not have been tightened, and the loose connection can overheat behind the dashboard. Recall 04V334 covers it.
- What to do
- Check the VIN for open recalls and have the free repair done. Stop driving and get the car checked if you smell burning plastic.
Free at a dealer under the recall.
Rear seat belt anchors may lack welds (recall)
- What you'll notice
- No symptom while driving.
- Why it happens
- Some cars left the factory missing spot welds on a rear floor reinforcement, so the rear seat belt and child seat anchors could tear loose in a crash. Recall 04V333 covers it.
- What to do
- Check your VIN for this recall and have it inspected and repaired free, especially if you carry children in the back.
Free at a dealer under the recall.
Front shoulder belt bolts may be loose (recall)
- What you'll notice
- Usually none, though a loose upper seat belt mount may rattle or move.
- Why it happens
- The bolts holding the front shoulder belt height adjusters may not have been tightened, so the belt could come free in a crash. Recall 04V335 covers it.
- What to do
- Have a dealer check and tighten the bolts for free under the recall.
Free at a dealer under the recall.
Rear brake lines can wear through (recall)
- What you'll notice
- Brake fluid leaking near the engine, a soft or sinking brake pedal, or the brake warning light.
- Why it happens
- On 2.7L cars a rear brake tube can rub against the EGR tube until it wears a hole. Recall 06V149 replaces the tubes and adds a clip.
- What to do
- If the pedal feels soft, do not drive the car. Check your VIN for this recall and get it fixed free.
Free at a dealer under the recall.
Gearshift cable can come off (recall)
- What you'll notice
- The shifter shows one gear while the transmission is in another, and the car could move when you expect it to stay put.
- Why it happens
- The gearshift cable can pop out of its bracket on the transmission. Recall 08V583 adds a locking clip.
- What to do
- Use the parking brake every time you park and have the free recall repair done.
Free at a dealer under the recall.
Drive wheels can briefly lock during shifts (recall)
- What you'll notice
- If you shift to Neutral and back to Drive above about 40 mph, the rear wheels can lock for a moment.
- Why it happens
- A software fault in the powertrain computer caused it. Recall 06V341 reprograms the computer.
- What to do
- Do not shift into Neutral at speed, and have the free software update done if it is still open.
Free at a dealer under the recall.
ABS software can lock the rear brakes (recall)
- What you'll notice
- The rear wheels lock up during some hard or uneven braking, making the car slide or spin.
- Why it happens
- A software error in the anti-lock brake module allowed rear-wheel lockup. Recall 06V493 reprograms it.
- What to do
- Check the VIN and have the free ABS update done before driving in slippery weather.
Free at a dealer under the recall.
Rear axle hub nuts can loosen (recall)
- What you'll notice
- Clicking or clunking from a rear wheel, then loss of drive if the axle shaft comes out.
- Why it happens
- The rear hub nuts were not crimped at the factory, so they could back off and let the half-shaft separate. Recall 08V295 covers it.
- What to do
- Have the free recall check done. If you hear clunking from the rear, have it inspected before driving further.
Free at a dealer under the recall.
Key can stick between Start and On and stall (recall)
- What you'll notice
- After starting, the key may not spring all the way back to On. The engine can then shut off while driving, cutting power steering, power brakes and the air bags.
- Why it happens
- Parts of the ignition switch can hold the key between positions. Recall 14V567 fixes the switch.
- What to do
- Make sure the key returns fully to On after starting, and have the free recall repair done.
Free at a dealer under the recall.
Shifter stuck in Park
- What you'll notice
- The engine starts but the gear lever will not come out of Park even with your foot on the brake. It may free up after a few tries or not at all, leaving you stranded.
- Why it happens
- A small pink plastic piece and its spring inside the shift-lock mechanism of the shifter break or come loose, so the lock never releases.
- What to do
- Pry off the trim beside the shifter and press the shift-lock release tab to get the car into gear in an emergency. For a lasting fix, have the shifter's shift-lock parts or the whole shifter assembly replaced, and check that the brake lights work, since the brake switch also controls the lock.
Stalls after filling the gas tank
- What you'll notice
- Shortly after refueling the engine stalls at a stop or while driving, or it takes a lot of cranking to start. The gas pump may also click off early.
- Why it happens
- Liquid fuel gets past the tank's fill and vent valve into the evaporative emissions canister and purge valve. That floods the engine with raw fuel vapor and can saturate the canister.
- What to do
- Stop filling at the first click and never top off. Have the evaporative system checked; repairs can include the tank vent valve, canister and purge solenoid, and in some cases the fuel tank.
ESP light comes on and the car loses power
- What you'll notice
- The ESP (stability control) light flashes or stays on, sometimes with the ABS light, and the car stops accelerating normally or stalls. Restarting usually brings things back to normal for a while.
- Why it happens
- No single cause has been confirmed. Wheel speed sensor, throttle and electrical module faults have all been blamed, and the car cuts power when the stability system thinks something is wrong.
- What to do
- Have the ABS and engine codes read while the lights are on. If it keeps happening, avoid using cruise control and get it diagnosed, since losing power at speed is dangerous.
Clunking front suspension and fast tie rod wear
- What you'll notice
- Clunks or thumps over bumps and road seams, a loose or wandering feel in the steering, and uneven front tire wear.
- Why it happens
- The front tension strut bushings, ball joints, control arm bushings, tie rods and sway bar links on these heavy cars wear out early. Owners often replace several parts before finding the worn one.
- What to do
- Have the whole front end inspected at once so the right part is found, then get an alignment. Worn tie rods and ball joints affect steering, so do not put it off.
Broken exhaust manifold bolts (HEMI)
- What you'll notice
- A ticking or tapping noise from the engine that is loudest on a cold start and fades as it warms up, sometimes with an exhaust smell.
- Why it happens
- Heat makes the HEMI's cast iron exhaust manifolds warp, which snaps the bolts, usually at the rear of the passenger side, and lets exhaust leak out.
- What to do
- Have a shop confirm where the tick comes from, since it can sound like a lifter problem. Replacing the broken bolts and gasket fixes it; extracting snapped bolts adds labor.
Gauges drop to zero while driving
- What you'll notice
- The speedometer, tachometer and other gauges suddenly fall to zero and warning lights flicker, then come back.
- Why it happens
- Communication faults in the front control module (FCM) and integrated power module, or in the instrument cluster, interrupt the signal to the gauges.
- What to do
- Note when it happens and have a shop scan all modules for stored communication codes. Software updates and module replacement are the usual fixes.
Power module (TIPM) failure causes odd electrical faults
- What you'll notice
- Hard starting or cranking with no start, the fuel pump running when it should not, stalling, the horn going off on its own, or wipers and windows acting up.
- Why it happens
- The totally integrated power module (TIPM) under the hood controls power to many systems. When its internal relays or circuits fail, several unrelated things go wrong at once.
- What to do
- Have a shop that knows Chrysler products test the TIPM before replacing the fuel pump or other parts. A new or rebuilt module is the usual fix.
Headlights and other lights flicker or cut out
- What you'll notice
- The headlights, parking lights and dash lights flicker or go out while driving even though the switch is on. Turning the switch off and on can bring them back.
- Why it happens
- Owners suspect the headlight switch or a relay or module that controls the lights, but no single cause has been confirmed.
- What to do
- Treat this as urgent, since losing headlights at night is dangerous. Have the headlight switch and lighting circuit tested.
Driveshaft rubber coupling fails
- What you'll notice
- A vibration, clunk or thumping from under the middle of the car when pulling away or shifting.
- Why it happens
- The rubber coupling (flex disc) that joins the driveshaft to the transmission or axle cracks and breaks down with age and miles.
- What to do
- Have the driveshaft couplings inspected. Replace a cracked one before it lets go, because a loose driveshaft can damage the car.
Rear power windows stop working
- What you'll notice
- One or both rear windows stop going up or down. It can be on and off, and sometimes pressing the switch several times or tapping the door panel makes it work again.
- Why it happens
- A worn window motor is the most common repair, though a corroded switch, connector or poor ground can do the same thing.
- What to do
- Have the motor tested at the door connector. If power reaches the motor and it does not run, replace the motor; if not, check the switch and wiring.
Key breaks inside and won't start the car
- What you'll notice
- The key turns but the car will not start or the key feels loose, and the spare may fail the same way.
- Why it happens
- The plastic key head breaks internally, damaging the chip and buttons that the car needs to recognize the key.
- What to do
- Order a new key and have it programmed by a dealer or locksmith. Keep a working spare.
Repair prices for your Dodge Magnum
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace engine with a used or remanufactured 2.7L V6
- Replace engine with a remanufactured 5.7L HEMI
- Replace automatic transmission with a remanufactured unit
- Repair shift-lock or replace gear shifter assembly
- Replace crankshaft and camshaft position sensors
- Replace fuel tank vent valve, EVAP canister and purge valve
- Diagnose stability control and engine codes
- Replace front tension strut bushings, tie rod ends and align
- Replace exhaust manifold bolts and gasket
- Replace instrument cluster (used or new) and set mileage
- Replace and program the totally integrated power module (TIPM)
- Replace headlight switch (after testing the lighting circuit)
- Replace rear power window motor, one door
- Buy, cut and program a replacement key/remote
- Replace driveshaft flex coupling
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Recall repair at a dealerNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.