Your 2008 Dodge Magnumproblems, repair costs and recalls
What we've documented about the 2008 Dodge Magnum: problems owners and shops report, typical repair and upkeep costs, and safety recalls.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems for your 2008 Dodge Magnum
11 documented issues apply to 2008, most serious first.
Oil sludge or coolant in the oil ruins the engine (2.7L)
- What you'll notice
- Knocking or ticking that gets worse, an oil pressure light, milky or very dark thick oil, coolant that keeps going down with no outside leak, and eventually an engine that seizes or won't restart.
- Why it happens
- The 2.7L V6 runs hot and holds little oil, so it is prone to sludge, especially when oil changes are stretched. Its water pump sits behind the timing chain, and when the pump's seal or gasket leaks, coolant goes straight into the oil and destroys the bearings.
- What to do
- Change the oil on time with the correct synthetic and watch the coolant level closely. If coolant drops with no visible leak or the oil looks milky, stop driving and have the water pump checked right away. If the engine is already knocking, get a second opinion before paying for repairs, since replacement is often the realistic fix.
Dropped valve seat destroys a cylinder (HEMI)
- What you'll notice
- A sudden misfire with a flashing check engine light, a loud metallic knock, loss of power, smoke from the exhaust, and in some cases the engine dying while you drive. The starter may spin unusually fast because a cylinder has lost compression.
- Why it happens
- The 5.7L HEMI uses valve seats pressed into its aluminum heads. If the head runs hot, often after a cooling problem, a seat can loosen and fall into the cylinder, smashing the valve, piston and cylinder wall.
- What to do
- Pull over and shut the engine off if it starts knocking hard; driving on it spreads the damage. Have a compression test done. Expect a cylinder head and possibly engine replacement, so get a written quote and compare a remanufactured engine with a repair.
Automatic transmission failure
- What you'll notice
- Whining from the transmission, then slipping, no reverse, or the car suddenly losing all drive and refusing to move, sometimes on the highway. Failures are reported anywhere from about 30,000 to over 180,000 miles.
- Why it happens
- The automatic transmissions in these cars wear out internally. Some owners also traced damage to coolant getting into the fluid through the transmission cooler in the radiator, or to failed speed sensors and control modules.
- What to do
- Check the transmission fluid; if it is pink and milky, coolant has mixed in and the radiator must be replaced along with the transmission repair. Have the codes read before agreeing to a rebuild, since a sensor can cause similar symptoms.
Takata air bag inflators can rupture (recall)
- What you'll notice
- Usually no symptom. The driver and passenger front air bags can explode with too much force in a crash and throw metal pieces into the cabin.
- Why it happens
- The Takata inflators break down after years of heat and humidity. Recalls 15V313 (driver) and 16V352 (passenger) cover these cars.
- What to do
- Ask the dealer to confirm the recall applies to your VIN and have the free replacement done right away if it is still open.
Free at a dealer under the recall.
Gearshift cable can come off (recall)
- What you'll notice
- The shifter shows one gear while the transmission is in another, and the car could move when you expect it to stay put.
- Why it happens
- The gearshift cable can pop out of its bracket on the transmission. Recall 08V583 adds a locking clip.
- What to do
- Use the parking brake every time you park and have the free recall repair done.
Free at a dealer under the recall.
Rear axle hub nuts can loosen (recall)
- What you'll notice
- Clicking or clunking from a rear wheel, then loss of drive if the axle shaft comes out.
- Why it happens
- The rear hub nuts were not crimped at the factory, so they could back off and let the half-shaft separate. Recall 08V295 covers it.
- What to do
- Have the free recall check done. If you hear clunking from the rear, have it inspected before driving further.
Free at a dealer under the recall.
Key can stick between Start and On and stall (recall)
- What you'll notice
- After starting, the key may not spring all the way back to On. The engine can then shut off while driving, cutting power steering, power brakes and the air bags.
- Why it happens
- Parts of the ignition switch can hold the key between positions. Recall 14V567 fixes the switch.
- What to do
- Make sure the key returns fully to On after starting, and have the free recall repair done.
Free at a dealer under the recall.
Clunking front suspension and fast tie rod wear
- What you'll notice
- Clunks or thumps over bumps and road seams, a loose or wandering feel in the steering, and uneven front tire wear.
- Why it happens
- The front tension strut bushings, ball joints, control arm bushings, tie rods and sway bar links on these heavy cars wear out early. Owners often replace several parts before finding the worn one.
- What to do
- Have the whole front end inspected at once so the right part is found, then get an alignment. Worn tie rods and ball joints affect steering, so do not put it off.
Broken exhaust manifold bolts (HEMI)
- What you'll notice
- A ticking or tapping noise from the engine that is loudest on a cold start and fades as it warms up, sometimes with an exhaust smell.
- Why it happens
- Heat makes the HEMI's cast iron exhaust manifolds warp, which snaps the bolts, usually at the rear of the passenger side, and lets exhaust leak out.
- What to do
- Have a shop confirm where the tick comes from, since it can sound like a lifter problem. Replacing the broken bolts and gasket fixes it; extracting snapped bolts adds labor.
Gauges drop to zero while driving
- What you'll notice
- The speedometer, tachometer and other gauges suddenly fall to zero and warning lights flicker, then come back.
- Why it happens
- Communication faults in the front control module (FCM) and integrated power module, or in the instrument cluster, interrupt the signal to the gauges.
- What to do
- Note when it happens and have a shop scan all modules for stored communication codes. Software updates and module replacement are the usual fixes.
Power module (TIPM) failure causes odd electrical faults
- What you'll notice
- Hard starting or cranking with no start, the fuel pump running when it should not, stalling, the horn going off on its own, or wipers and windows acting up.
- Why it happens
- The totally integrated power module (TIPM) under the hood controls power to many systems. When its internal relays or circuits fail, several unrelated things go wrong at once.
- What to do
- Have a shop that knows Chrysler products test the TIPM before replacing the fuel pump or other parts. A new or rebuilt module is the usual fix.
Repair prices for your 2008 Dodge Magnum
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace engine with a used or remanufactured 2.7L V6
- Replace engine with a remanufactured 5.7L HEMI
- Replace automatic transmission with a remanufactured unit
- Replace front tension strut bushings, tie rod ends and align
- Replace exhaust manifold bolts and gasket
- Replace instrument cluster (used or new) and set mileage
- Replace and program the totally integrated power module (TIPM)
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Recall repair at a dealerNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Checking the NHTSA recall database…