Your 1999 Ford Contourproblems, repair costs and recalls
What we've documented about the 1999 Ford Contour: problems owners and shops report, typical repair and upkeep costs, and safety recalls.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems for your 1999 Ford Contour
19 documented issues apply to 1999, most serious first.
Automatic transmission slipping or failing
- What you'll notice
- The car slips out of gear, loses gears, shifts late or harshly, or will not move forward. Many failures happen around 100,000-140,000 miles.
- Why it happens
- The CD4E automatic in the Contour has a known weakness, often starting with the front pump. Ford also issued bulletins for no forward drive and no overdrive on this transmission.
- What to do
- Check the fluid level and smell. If it slips or will not move, stop driving it hard and get a transmission diagnosis. On a car this age a used or rebuilt transmission is usually the most sensible fix.
Water pump failure and overheating
- What you'll notice
- Coolant leaking from the front of the engine, the temperature gauge climbing, steam, or the engine overheating. Some owners replaced the pump several times.
- Why it happens
- The water pump on these cars used a plastic impeller that can crack or break apart, and pump bearings and housings also failed. Ford sent owner notices about water pump bearing and housing failures.
- What to do
- Stop driving as soon as the gauge climbs, since overheating can ruin the head gasket. When replacing the pump, ask for one with a metal impeller.
Stalls or dies while driving from fuel pump failure
- What you'll notice
- The engine loses power and dies while driving, may restart after sitting, or cranks but will not start.
- Why it happens
- Owners most often trace this to a failing fuel pump or no power reaching the pump. A tripped or faulty fuel shutoff (inertia) switch can do the same thing.
- What to do
- If it dies, get safely off the road. Have a shop check fuel pressure and whether the pump is getting power before replacing parts.
Blower motor resistor can overheat and melt (recall)
- What you'll notice
- A burning plastic smell, some fan speeds stop working, or the blower quits. The connector may be melted.
- Why it happens
- The heater blower resistor could overheat and damage its wiring connector, causing arcing and a fire risk. Ford recalled these cars to replace the resistor and harness and also extended the warranty on earlier cars.
- What to do
- Stop using the fan if you smell burning. Check your VIN for the recall and have the resistor and connector replaced.
Recalls this old may no longer be done by dealers; ask with your VIN.
Rear brakes can lock up from a corroded valve (recall)
- What you'll notice
- The rear wheels lock or skid during hard braking, especially on cars driven on salted roads.
- Why it happens
- On cars without ABS, the rear brake pressure-reducing valves could corrode from road salt and stop working, letting the rear brakes lock. Ford recalled 1996-1998 cars and later added 1999-2000 cars.
- What to do
- Check your VIN for the recall and make sure the improved valves were installed.
Recalls this old may no longer be done by dealers; ask with your VIN.
Key can be removed when not in Park (recall)
- What you'll notice
- You can take the key out while the automatic transmission is not in Park, so the car could roll away.
- Why it happens
- A fault in the steering column on some 1999 automatic Contours let the key come out outside of Park. Ford recalled these cars to inspect and replace the column where needed.
- What to do
- Always check that the car is in Park and set the parking brake. Check your VIN for the recall.
Recalls this old may no longer be done by dealers; ask with your VIN.
Timing belt shredding (2.0L)
- What you'll notice
- A slapping or rubbing noise from the front of the engine, or the engine suddenly stopping and not restarting.
- Why it happens
- Ford issued a bulletin for 2.0L Zetec timing belts shredding or hitting the front cover. If the belt breaks, the engine stops and can be damaged inside.
- What to do
- Replace the timing belt on schedule, around 120,000 miles, or sooner if you do not know when it was last done. Have any noise from the belt area checked right away.
Manual transmission differential failure (V6)
- What you'll notice
- Grinding or clunking from the transmission, then the car will not move even though the engine runs.
- Why it happens
- Ford issued bulletins about differential failures in the 5-speed manual on V6 cars, sometimes linked to hard launches.
- What to do
- Stop driving if you hear grinding from the transmission. A used transmission or a rebuild is usually needed.
Check engine light from clogged EGR passages
- What you'll notice
- The check engine light comes on with an EGR flow code, and the engine may ping or knock under load.
- Why it happens
- Carbon can plug the exhaust gas recirculation (EGR) passages so not enough exhaust flows back into the engine. Ford issued a bulletin for EGR flow codes on these cars.
- What to do
- Have the codes read. Cleaning the EGR passages and checking the EGR valve and sensor usually fixes it.
Lean codes from vacuum leaks (V6)
- What you'll notice
- The check engine light comes on with codes P0171 and P0174, and the idle may be rough.
- Why it happens
- Cracked vacuum hoses or leaking intake gaskets let in extra air, making the engine run lean. Ford issued a bulletin for these codes from vacuum leaks.
- What to do
- Have a shop do a smoke test to find the leak. It is usually a cheap hose or gasket.
Rough idle and stalling at idle
- What you'll notice
- The engine idles rough or unevenly, stalls when coming to a stop, or makes a hooting noise from the idle air valve when slowing down.
- Why it happens
- Dirty or failing idle air control valves and vacuum leaks are common causes. Ford issued bulletins for rough idle, stalling and noise from the idle air bypass valve.
- What to do
- Have the idle air control valve cleaned or replaced and check for vacuum leaks.
Hard starting in freezing weather (2.0L)
- What you'll notice
- Long cranking, a hard start, stalling or rough idle when the engine is cold, especially below freezing.
- Why it happens
- Ford issued bulletins for 2.0L Zetec cars that over-fuel and start hard in cold weather, fixed with updated engine software or parts.
- What to do
- Have the engine checked for codes and ask about the cold-start bulletins.
Heater core leak
- What you'll notice
- A sweet coolant smell inside, foggy windows, a wet passenger floor, or coolant slowly disappearing.
- Why it happens
- Ford issued a bulletin for heater core leaks on these cars. The heater core is behind the dashboard.
- What to do
- Check the coolant level and look for wet carpet. Replacing the core is a big job because much of the dash comes out.
Steering wheel shakes when braking
- What you'll notice
- The steering wheel or car vibrates when you brake, especially from highway speed.
- Why it happens
- Ford issued bulletins about brake vibration on these cars, usually from uneven front rotors and pad material.
- What to do
- Have the front rotors and pads inspected. New or resurfaced rotors and pads usually fix it.
Front wheel bearing noise
- What you'll notice
- A humming or growling noise that grows with speed and may change when turning.
- Why it happens
- Ford issued a bulletin for front wheel bearing noise on these cars.
- What to do
- Have the wheel bearings checked. A badly worn bearing can affect steering and braking.
Starter grinding when starting
- What you'll notice
- A grinding noise when you start the car, or the starter spins without turning the engine.
- Why it happens
- Ford issued a bulletin for starter grinding and poor engagement on these cars.
- What to do
- Have the starter and its mounting checked. A worn starter usually needs replacing.
Dashboard top lifting away from the windshield
- What you'll notice
- The top of the dash curls up near the windshield, exposing the clips underneath and blocking the defroster.
- Why it happens
- The dash top pulls loose over time, especially after hot summers. Owners report it around 47,000 miles on average.
- What to do
- Have a shop or trim specialist re-secure the dash. Keep the windshield clear in winter, since the defroster may not work well.
Water leaking onto the front floor
- What you'll notice
- Wet carpet on the front floor after rain or a car wash.
- Why it happens
- Ford issued a bulletin for water getting in around the door panel area and wetting the front floor.
- What to do
- Have the door water shield and seals checked and resealed. Dry the carpet quickly to prevent mold and rust.
Temperature gauge reads high when the engine is not hot
- What you'll notice
- The temperature gauge sits higher than normal even though the engine is not overheating.
- Why it happens
- Ford issued bulletins for temperature gauges reading high at normal operating temperature.
- What to do
- Make sure the engine is not really overheating first: check coolant level and the fan. Then have the sensor and gauge checked.
Repair prices for your 1999 Ford Contour
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace automatic transmission with used or rebuilt unit
- Replace water pump and refill coolant
- Replace fuel pump assembly
- Clean EGR passages; replace EGR valve or sensor if needed
- Smoke test and replace vacuum hose or intake gasket
- Clean or replace idle air control valve
- Replace timing belt and tensioner
- Cold-start bulletin repair or engine software update
- Replace manual transmission with used or rebuilt unit
- Replace starter
- Replace heater core
- Replace front brake pads and rotors
- Replace front wheel bearing
- Re-secure dashboard top
- Reseal door water shield
- Replace coolant temperature sender
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Free recall repair at a Ford dealerNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Checking the NHTSA recall database…