Ford E-Seriesproblems, repair costs and recalls
Problems reported across 1996–2027. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
35 documented issues across all years, most serious first.
Spark plug blows out of the cylinder head
- What you'll notice
- A sudden loud popping or ticking like a gunshot under the engine cover, then a rough-running engine, loss of power and a check engine light.
- Why it happens
- The aluminum heads on Ford's 4.6L, 5.4L and 6.8L engines of this era had only a few threads holding each spark plug. Over time a plug can work loose and shoot out, often stripping the threads and sometimes damaging the ignition coil.
- What to do
- Stop driving as soon as it is safe; the open hole can damage wiring and the coil. A shop can usually repair the threads with an insert without pulling the head.
Cracked plastic intake manifold leaks coolant
- What you'll notice
- A sudden coolant leak at the front top of the engine, a sweet smell, steam, or the temperature gauge climbing.
- Why it happens
- Early 4.6L and 5.4L engines used a plastic intake manifold whose front coolant passage can crack with age and heat, letting coolant pour out with little warning.
- What to do
- Pull over if the engine overheats. Replacement manifolds with a reinforced coolant crossover fix the problem for good.
Head gasket failure (6.0L diesel)
- What you'll notice
- Coolant disappearing with no visible leak, a coolant reservoir that bubbles or is pressurized, white exhaust smoke, or overheating when working hard.
- Why it happens
- The 6.0L diesel holds its heads on with stretch-type bolts. Extra cylinder pressure, often after an oil cooler or EGR cooler failure or engine tuning, can stretch them and blow the head gaskets. Some E-Series owners report cracked heads and blocks.
- What to do
- Stop driving if it is overheating or pushing coolant out. The lasting repair is new head gaskets with stronger head studs, and the coolers should be checked at the same time.
Oil cooler clogs and EGR cooler cracks (6.0L diesel)
- What you'll notice
- White steam-like smoke at startup, coolant loss, and overheating when loaded or towing.
- Why it happens
- The engine oil cooler can clog with debris, which starves the EGR cooler of coolant. The overheated EGR cooler then cracks and lets coolant into the exhaust or intake.
- What to do
- Have a diesel shop compare oil and coolant temperatures to check the oil cooler. Fixing it early can save the head gaskets.
Injector control module (FICM) failure (6.0L diesel)
- What you'll notice
- Hard or no starts when cold, rough idle, misfires or stalling, often worse with a weak battery.
- Why it happens
- The module that fires the injectors sits on top of the engine. Heat, vibration and low battery voltage wear out its internal power supply.
- What to do
- Have the module voltage tested and make sure the batteries are healthy. A rebuilt or upgraded module is the usual fix.
6.0L diesel may stall without warning (recall)
- What you'll notice
- The engine dies while driving and may not restart.
- Why it happens
- A wiring problem at the injector control module harness or oil pressure sensor connector could shut the engine off. Ford recalled these vans to upgrade the harness or connector.
- What to do
- Check your VIN for the recall; the fix is free at a Ford dealer.
Camshaft position sensor failure (7.3L diesel)
- What you'll notice
- The engine stalls or will not start, and the tachometer may drop to zero while driving.
- Why it happens
- The camshaft position sensor on the 7.3L Power Stroke fails intermittently. Ford recalled some trucks for it.
- What to do
- Carry a spare if you rely on the van; the sensor is cheap and quick to replace. Check the connector too.
Cruise control switch can overheat and catch fire (recall)
- What you'll notice
- Usually no warning. In rare cases there is smoke or a burning smell from the engine compartment, even with the van parked and off.
- Why it happens
- A cruise control deactivation switch on the brake master cylinder can leak brake fluid internally, overheat and start an underhood fire. Ford recalled many trucks, vans and motorhome chassis to add a fused harness.
- What to do
- Check your VIN for the cruise control switch recall and have the fused harness installed. Park outside until it is done.
Automatic transmission slipping or failing
- What you'll notice
- Slipping, delayed or harsh shifts, flaring between gears, or losing drive altogether, especially in heavily loaded vans.
- Why it happens
- Heavy loads and heat wear out the automatic transmission. Owners of these years report full replacements around 90,000 to 100,000 miles.
- What to do
- Check the fluid level and condition. Change the fluid regularly, and consider an auxiliary cooler if you tow or carry heavy loads.
Fuel rail crossover hose can crack and leak (recall)
- What you'll notice
- A gasoline smell from the engine area or fuel dripping near the engine.
- Why it happens
- The crossover hose on the 5.4L engine's fuel rail can crack and leak fuel, which is a fire risk. Ford recalled the vans to replace the fuel rail.
- What to do
- Do not drive if you smell fuel. Check your VIN for the recall.
Windshield wipers can stop working (recall)
- What you'll notice
- The wipers quit, often in bad weather when you need them most.
- Why it happens
- Some wiper motors left the factory without grease on the output gear, which can wear and break. Ford recalled these vans to inspect and grease the gear.
- What to do
- Check your VIN for the wiper motor recall.
Rear axle failure
- What you'll notice
- Whining, clunking or grinding from the rear axle, then loss of drive.
- Why it happens
- Owners report rear axle and drivetrain failures on heavily used vans around 100,000 miles.
- What to do
- Have the rear axle fluid checked for metal and the bearings inspected at the first sign of noise.
Engine stalls or shuts off while driving
- What you'll notice
- The engine dies in traffic, sometimes at low mileage, with power steering and brake assist dropping away.
- Why it happens
- Owners of 2007 cutaways and 2013 vans report sudden shutdowns. Causes vary, so proper diagnosis is needed.
- What to do
- Treat it as a safety problem. Have stored codes read right after it happens, and check for open recalls.
Driver seat track can break in a crash (recall)
- What you'll notice
- No warning to the driver.
- Why it happens
- A gear in the power driver seat track could fracture in a crash and let the seat move. Ford recalled these vans to inspect and replace it.
- What to do
- Check your VIN for the seat recall.
Seat bolts may break (recall)
- What you'll notice
- No warning to the driver.
- Why it happens
- Some bolts used to install seats were made incorrectly and could fracture. Ford recalled affected vehicles to replace them.
- What to do
- Check your VIN for the recall.
Trailer brake controller may not apply trailer brakes (recall)
- What you'll notice
- When towing, the trailer brakes do not work or work weakly, so the van and trailer take longer to stop.
- Why it happens
- Some vans with the factory trailer brake controller and the 6.8L engine had a software problem. Ford recalled them to reprogram the engine computer.
- What to do
- Do not tow until the recall software is installed.
Engine cover can get too hot (recall)
- What you'll notice
- The engine cover between the front seats gets very hot, with a hot smell in the cab. Passengers touching it can be burned.
- Why it happens
- Insulation on the engine cover could be out of place and the engine's heat-management software let the cover overheat. Ford recalled these vehicles, then re-recalled some after incomplete software updates.
- What to do
- Check your VIN for both engine cover recalls and keep people from resting against the cover until it is fixed.
Power steering line can leak and cut brake assist (recall)
- What you'll notice
- A sudden fluid leak, heavy steering and a hard brake pedal.
- Why it happens
- On dual-rear-wheel models the power steering pressure line was not connected well at the hydraulic brake booster, so fluid could escape and take away both steering and brake assist.
- What to do
- Check your VIN for both recalls on this line. If steering suddenly gets heavy, slow down and stop safely.
Wiring can rub through and stall the engine (recall)
- What you'll notice
- Stalling, or ABS and stability control warnings.
- Why it happens
- A rear wiring harness could rub on the frame and damage fuel pump circuits. Ford recalled affected chassis.
- What to do
- Check your VIN for the recall.
Rear axle may be low on fluid (recall)
- What you'll notice
- Whining or grinding from the rear axle, then possible axle failure.
- Why it happens
- Some rear axles were filled below the minimum level at the factory. Ford recalled them to check and fill.
- What to do
- Check your VIN for the recall.
Fuel tank seam can rust and leak (recall)
- What you'll notice
- A fuel smell or drips near the fuel tank.
- Why it happens
- Paint on the fuel tank's weld seam can peel and let it corrode, which can lead to a leak and fire risk. Ford recalled these chassis to inspect and replace tanks as needed.
- What to do
- If you smell fuel, park outside and check your VIN for the recall.
Rear brake rotor bolts may be loose (recall)
- What you'll notice
- Clunking or vibration from a rear wheel; in the worst case a wheel could come off.
- Why it happens
- Rear axle rotor bolts on some E-450 chassis may not have been tightened correctly. Ford recalled them to check the bolts.
- What to do
- Check your VIN for the recall and stop driving if you hear new clunks from the rear wheels.
Park may not hold the vehicle (recall)
- What you'll notice
- The vehicle can roll after being shifted into Park.
- Why it happens
- A casting defect in the transmission can stop the park pawl from fully engaging. Ford recalled these vehicles to inspect and replace transmission parts.
- What to do
- Always set the parking brake and check your VIN for the recall.
Blower motor may fail and disable the defroster (recall)
- What you'll notice
- The heater and defroster fan stops working and the windshield fogs or ices up.
- Why it happens
- Some blower motors on vehicles built in spring 2025 can fail. Ford recalled them.
- What to do
- Check your VIN for the recall and do not drive if you cannot clear the windshield.
Rough running and misfires with check engine light
- What you'll notice
- The engine shakes or stumbles, especially when accelerating with a load, and the check engine light comes on or flashes.
- Why it happens
- A rough-running engine with misfires is the most-reported E-350 problem on RepairPal. On these gas engines it is usually a worn spark plug, a failing coil-on-plug ignition coil or its rubber boot.
- What to do
- Have the misfire codes read to find the cylinder. A flashing check engine light means stop working the engine hard, because raw fuel can overheat the catalytic converter.
Front end rattles and loose steering
- What you'll notice
- Rattling or clunking from the front over bumps, play in the steering wheel, wandering on the highway, or uneven front tire wear.
- Why it happens
- These are heavy vans and chassis, and front suspension and steering parts such as ball joints, tie rod ends and bushings wear under the weight. RepairPal lists front-end rattling and play in the front wheels among common E-350 complaints.
- What to do
- Have the front end inspected and aligned. Worn steering parts get worse quickly on a heavy vehicle and can affect control.
Sticking turbo vanes and injectors (6.0L diesel)
- What you'll notice
- Slow to build boost, poor power, rough running on cold starts that smooths out when warm, or oil leaking near the turbo drain tube.
- Why it happens
- Soot can stick the turbo's adjustable vanes, and the oil-driven injectors are sensitive to oil quality and can stick, especially with overdue oil changes.
- What to do
- Keep up with oil changes using diesel-rated oil. A shop can clean the turbo vanes; injector additives or injector replacement may be needed.
Misfires from injector wiring or driver module (7.3L diesel)
- What you'll notice
- Misfiring, rough running, lost power or stalling, often blamed on bad injectors at first.
- Why it happens
- Connectors on the wiring harness under the valve covers fail, and the injector driver module in the fender area can be damaged by moisture.
- What to do
- Have injector circuit codes read and the harness and module connectors checked before replacing injectors.
Coolant contamination from injector sleeves or oil cooler (7.3L diesel)
- What you'll notice
- Coolant loss, bubbles in the coolant, fuel smell in the coolant, or oil and coolant mixing.
- Why it happens
- On high-mileage engines the injector sleeves can crack and let fuel into the coolant, and aged oil cooler seals can leak.
- What to do
- Have the coolant tested for fuel or oil. Catching it early prevents bigger engine damage.
Check engine light with transmission solenoid codes
- What you'll notice
- Check engine light with transmission codes, sometimes with harsh or odd shifts.
- Why it happens
- Ford issued a bulletin for TorqShift automatics on these vans setting codes P0751, P0730 or P2700, on transmissions built before mid-December 2015.
- What to do
- Have the codes read and ask the dealer about bulletin 16-0057 before replacing parts.
Fuel tank lining breaks down and clogs the fuel system
- What you'll notice
- Loss of power, stalling, hard starting or clogged fuel filters again and again.
- Why it happens
- Owners report the coating inside the fuel tank coming apart and sending debris to the filters and pump.
- What to do
- Have the fuel filter cut open and inspected. If you find tank debris, the tank usually has to be replaced and the fuel system cleaned.
Windshield may form bubbles in heat (recall)
- What you'll notice
- Bubbles or distortion in the windshield, especially in hot weather, that make it hard to see.
- Why it happens
- Some windshields were made under the wrong conditions. Ford recalled affected vans to replace them as needed.
- What to do
- Check your VIN for the windshield recall.
Backup camera image may fail (recall)
- What you'll notice
- The rearview camera picture is blank or wrong when backing up.
- Why it happens
- Ford recalled some 2017-2019 vehicles for a rearview camera problem.
- What to do
- Check your VIN for open camera recalls and use mirrors and a spotter until it is fixed.
Backup alarm may not sound (recall)
- What you'll notice
- No beeping alarm when reversing.
- Why it happens
- The backup alarm connector can loosen and come off. Ford recalled affected chassis.
- What to do
- Check your VIN for the recall and use a spotter when backing up.
A/C cools poorly
- What you'll notice
- Weak cooling, temperature that does not match the setting, or a check engine light with code P06A0.
- Why it happens
- Ford issued a service message for poor A/C performance on vans and cutaways with the electronically controlled compressor.
- What to do
- Ask the dealer about service message 47850 and have the A/C system and compressor controls tested.
Repair prices for your Ford E-Series
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace ignition coil and spark plug on the misfiring cylinder
- Replace worn ball joints or tie rod ends, then align
- Repair spark plug threads with an insert, new plug and coil
- Replace intake manifold and gaskets
- Replace head gaskets and install head studs
- Replace engine oil cooler and EGR cooler
- Replace fuel injection control module (FICM)
- Remove and clean turbo vanes, replace unison ring
- Replace camshaft position sensor
- Replace under-valve-cover injector harness
- Reseal oil cooler or replace injector sleeves
- Replace automatic transmission with remanufactured unit
- Diagnose and replace transmission solenoid body
- Replace fuel tank, filters and clean fuel system
- Rebuild rear differential (gears and bearings)
- Diagnose stalling, then replace failed sensor or fuel part
- Diagnose A/C, recharge or replace compressor control valve
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Upgrade injector module harness or sensor connectorNo charge if your vehicle is included
- Install fused wiring harness for cruise control switchNo charge if your vehicle is included
- Replace fuel rail assemblyNo charge if your vehicle is included
- Inspect and grease wiper motor gearNo charge if your vehicle is included
- Inspect and replace driver seat trackNo charge if your vehicle is included
- Replace windshieldNo charge if your vehicle is included
- Replace seat mounting boltsNo charge if your vehicle is included
- Reprogram powertrain control moduleNo charge if your vehicle is included
- Inspect and repair or replace rearview cameraNo charge if your vehicle is included
- Reposition engine cover insulation and update softwareNo charge if your vehicle is included
- Repair power steering line connection at hydroboostNo charge if your vehicle is included
- Repair and reroute rear wiring harnessNo charge if your vehicle is included
- Check and top up rear axle fluidNo charge if your vehicle is included
- Inspect and replace fuel tank if neededNo charge if your vehicle is included
- Inspect and torque rear rotor boltsNo charge if your vehicle is included
- Inspect and replace transmission partsNo charge if your vehicle is included
- Replace HVAC blower motorNo charge if your vehicle is included
- Secure or replace backup alarm connectorNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.