Your 2009 Ford E-Seriesproblems, repair costs and recalls
What we've documented about the 2009 Ford E-Series: problems owners and shops report, typical repair and upkeep costs, and safety recalls.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems for your 2009 Ford E-Series
8 documented issues apply to 2009, most serious first.
Head gasket failure (6.0L diesel)
- What you'll notice
- Coolant disappearing with no visible leak, a coolant reservoir that bubbles or is pressurized, white exhaust smoke, or overheating when working hard.
- Why it happens
- The 6.0L diesel holds its heads on with stretch-type bolts. Extra cylinder pressure, often after an oil cooler or EGR cooler failure or engine tuning, can stretch them and blow the head gaskets. Some E-Series owners report cracked heads and blocks.
- What to do
- Stop driving if it is overheating or pushing coolant out. The lasting repair is new head gaskets with stronger head studs, and the coolers should be checked at the same time.
Oil cooler clogs and EGR cooler cracks (6.0L diesel)
- What you'll notice
- White steam-like smoke at startup, coolant loss, and overheating when loaded or towing.
- Why it happens
- The engine oil cooler can clog with debris, which starves the EGR cooler of coolant. The overheated EGR cooler then cracks and lets coolant into the exhaust or intake.
- What to do
- Have a diesel shop compare oil and coolant temperatures to check the oil cooler. Fixing it early can save the head gaskets.
Injector control module (FICM) failure (6.0L diesel)
- What you'll notice
- Hard or no starts when cold, rough idle, misfires or stalling, often worse with a weak battery.
- Why it happens
- The module that fires the injectors sits on top of the engine. Heat, vibration and low battery voltage wear out its internal power supply.
- What to do
- Have the module voltage tested and make sure the batteries are healthy. A rebuilt or upgraded module is the usual fix.
Engine stalls or shuts off while driving
- What you'll notice
- The engine dies in traffic, sometimes at low mileage, with power steering and brake assist dropping away.
- Why it happens
- Owners of 2007 cutaways and 2013 vans report sudden shutdowns. Causes vary, so proper diagnosis is needed.
- What to do
- Treat it as a safety problem. Have stored codes read right after it happens, and check for open recalls.
Rough running and misfires with check engine light
- What you'll notice
- The engine shakes or stumbles, especially when accelerating with a load, and the check engine light comes on or flashes.
- Why it happens
- A rough-running engine with misfires is the most-reported E-350 problem on RepairPal. On these gas engines it is usually a worn spark plug, a failing coil-on-plug ignition coil or its rubber boot.
- What to do
- Have the misfire codes read to find the cylinder. A flashing check engine light means stop working the engine hard, because raw fuel can overheat the catalytic converter.
Front end rattles and loose steering
- What you'll notice
- Rattling or clunking from the front over bumps, play in the steering wheel, wandering on the highway, or uneven front tire wear.
- Why it happens
- These are heavy vans and chassis, and front suspension and steering parts such as ball joints, tie rod ends and bushings wear under the weight. RepairPal lists front-end rattling and play in the front wheels among common E-350 complaints.
- What to do
- Have the front end inspected and aligned. Worn steering parts get worse quickly on a heavy vehicle and can affect control.
Sticking turbo vanes and injectors (6.0L diesel)
- What you'll notice
- Slow to build boost, poor power, rough running on cold starts that smooths out when warm, or oil leaking near the turbo drain tube.
- Why it happens
- Soot can stick the turbo's adjustable vanes, and the oil-driven injectors are sensitive to oil quality and can stick, especially with overdue oil changes.
- What to do
- Keep up with oil changes using diesel-rated oil. A shop can clean the turbo vanes; injector additives or injector replacement may be needed.
Check engine light with transmission solenoid codes
- What you'll notice
- Check engine light with transmission codes, sometimes with harsh or odd shifts.
- Why it happens
- Ford issued a bulletin for TorqShift automatics on these vans setting codes P0751, P0730 or P2700, on transmissions built before mid-December 2015.
- What to do
- Have the codes read and ask the dealer about bulletin 16-0057 before replacing parts.
Repair prices for your 2009 Ford E-Series
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace ignition coil and spark plug on the misfiring cylinder
- Replace worn ball joints or tie rod ends, then align
- Replace head gaskets and install head studs
- Replace engine oil cooler and EGR cooler
- Replace fuel injection control module (FICM)
- Remove and clean turbo vanes, replace unison ring
- Diagnose and replace transmission solenoid body
- Diagnose stalling, then replace failed sensor or fuel part
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Checking the NHTSA recall database…