Your 2011 GMC Canyonproblems, repair costs and recalls
What we've documented about the 2011 GMC Canyon: problems owners and shops report, typical repair and upkeep costs, and safety recalls.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems for your 2011 GMC Canyon
10 documented issues apply to 2011, most serious first.
4-speed automatic slips or loses gears
- What you'll notice
- The engine revs but the truck doesn't speed up, shifts come late or hard, or the truck gets stuck in a low gear and won't shift into 3rd or 4th.
- Why it happens
- The 4L60-E automatic used in these trucks wears its internal clutches and parts, especially with towing, heat or old fluid. Loss of 3rd and 4th gear is a classic failure of this transmission.
- What to do
- Check the fluid level and smell. If it slips or won't shift, have it diagnosed before driving much farther, because more damage raises the rebuild cost.
Hood may be missing its secondary latch (recall)
- What you'll notice
- Usually nothing until the main latch lets go; then the hood can fly open while driving.
- Why it happens
- Some trucks were built without the backup hood latch required by federal rules.
- What to do
- Check your VIN for open recalls. The dealer fixes it free.
Rear axle pin can break and lock the rear wheels (recall)
- What you'll notice
- A clunk or grinding from the rear axle; in the worst case the rear wheels lock up while driving.
- Why it happens
- The cross pin inside the rear differential was not heat-treated correctly and can fracture.
- What to do
- Check your VIN for open recalls. The dealer installs a new pin free.
Blower fan works only on some speeds or not at all
- What you'll notice
- The heater and A/C fan stops blowing, or works only on certain speeds (often only high). You may smell hot plastic near the passenger footwell.
- Why it happens
- The blower motor resistor fails, and the heat can melt its wiring connector. This is the most-reported problem on first-generation Canyons, usually around 90,000 miles.
- What to do
- Replace the resistor and check its connector for melting. If the connector is burned, replace it too, or the new resistor can fail again.
Passlock security light and engine won't crank
- What you'll notice
- The engine won't turn over, or it cranks and won't start, and a security or Passlock light shows on the dash. It may happen now and then at first, then every day.
- Why it happens
- The anti-theft system stops seeing the right signal from the ignition, usually because the ignition switch or the Passlock sensor in the steering column has failed or corroded.
- What to do
- A shop can read the security codes to confirm it. Replacing the ignition switch or the Passlock sensor usually fixes it; the parts are not expensive.
Timing chain rattle at startup
- What you'll notice
- A rattle from the engine for a few seconds after a cold start. If the chain stretches further you may see a check engine light, a rough idle, misfires or less power.
- Why it happens
- The timing chain stretches or its tensioner loses pressure over time, especially when oil changes are skipped or the oil is low.
- What to do
- Do not ignore a rattle that gets longer or louder. Have the codes checked; replacing the chain, guides and tensioner early costs far less than repairing a jumped timing chain.
Cam phaser (VVT actuator) rattle and rough running
- What you'll notice
- A rattle on startup, a check engine light with cam timing codes such as P0017, a rough idle or misfires.
- Why it happens
- The variable valve timing actuator on the camshaft, or the oil control solenoid that feeds it, wears or gets clogged with sludge, so cam timing goes out of range.
- What to do
- Have the codes read. Sometimes only the inexpensive solenoid is needed; a worn actuator costs more. Fresh oil at the right level helps prevent it.
Random electrical problems from corroded grounds
- What you'll notice
- Power windows or locks quit, lights act up, gauges flicker, or the truck sometimes won't start, with no clear pattern.
- Why it happens
- Ground wire splice packs under the hood corrode, and a weak body control module ground can cause several systems to misbehave at once.
- What to do
- Have a shop check the battery, then the ground splices and body control module ground before replacing expensive modules.
Frame and body rust
- What you'll notice
- Bubbling paint and rust on the cab corners, rocker panels and bed, and scaly rust on the frame rails that can turn into holes.
- Why it happens
- Salted winter roads and years of outdoor parking let rust take hold, especially on trucks used for work.
- What to do
- Have the frame inspected on a lift, especially before buying. Frame holes are a safety problem and can fail inspection.
EVAP leak or gas cap check engine light
- What you'll notice
- Check engine light, sometimes with a 'Check fuel cap' message. Codes are often P0455 or P0449/P0450. The truck drives normally.
- Why it happens
- A worn gas cap that no longer seals, or a sticking EVAP vent valve or canister, lets the fuel vapor system fail its self-test.
- What to do
- Make sure the cap clicks tight first. If the light comes back, have the code read; a new cap or vent valve is a cheap fix.
Repair prices for your 2011 GMC Canyon
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Rebuild or replace 4L60-E automatic transmission
- Replace blower motor resistor and wiring connector
- Replace ignition switch or Passlock sensor
- Replace timing chain, guides and tensioner
- Replace cam phaser oil control solenoid or actuator
- Replace gas cap, EVAP vent valve or canister
- Rust repair on body panels or frame sections
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Replace hood with secondary latchNo charge if your vehicle is included
- Replace rear differential cross pinNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Checking the NHTSA recall database…