Your 2000 GMC Sierra 1500problems, repair costs and recalls
What we've documented about the 2000 GMC Sierra 1500: problems owners and shops report, typical repair and upkeep costs, and safety recalls.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems for your 2000 GMC Sierra 1500
8 documented issues apply to 2000, most serious first.
Rusted steel brake lines can burst
- What you'll notice
- The brake pedal suddenly sinks much lower than normal or goes nearly to the floor, sometimes with brake fluid dripping near a wheel or along the frame.
- Why it happens
- The steel brake lines run along the frame where road salt and moisture collect. After many winters they rust from the outside until a line gives way under pressure.
- What to do
- If the pedal feels low or soft, do not keep driving. Have a shop inspect every brake line along the frame and replace corroded sections, ideally with corrosion-resistant line.
4-speed automatic wears out
- What you'll notice
- Slipping, flaring revs between gears, harsh or late shifts, losing certain gears, or the truck not moving in drive.
- Why it happens
- The 4L60-E four-speed automatic in many of these trucks wears internally, especially with towing or heavy loads, and commonly needs a rebuild at higher mileage.
- What to do
- Stop towing and get it checked at the first sign of slipping. Driving on a slipping transmission can turn a repair into a full rebuild.
In-tank fuel pump wears out
- What you'll notice
- A louder whine from the fuel tank, long cranking before it starts, sputtering under load, or the engine quitting while driving.
- Why it happens
- The electric pump inside the tank wears out with age. Owners report it fails sooner on trucks often run with a low fuel level, since the fuel helps cool the pump.
- What to do
- If the truck stalls or struggles to start, have fuel pressure tested before replacing parts. Keeping the tank above a quarter full may help the pump last.
Blower motor resistor fails or burns its connector
- What you'll notice
- The fan works only on high or on one speed, or stops entirely; sometimes a hot plastic smell from under the dash.
- Why it happens
- The resistor that sets the fan speed overheats and fails, and on some trucks the heat damages its wiring plug. GM sold an upgraded harness for this.
- What to do
- Replace the resistor and check the connector for melting. If the plug is scorched, replace it too so the problem does not return.
Front wheel speed sensor and hub failure
- What you'll notice
- ABS and brake warning lights on together, the ABS kicking in at low speed, or a grinding hum from a front wheel.
- Why it happens
- The front ABS speed sensors are built into the wheel hub assemblies, and they corrode or fail with the bearings. The usual fix is a new hub.
- What to do
- Have the ABS codes read to find which wheel is at fault, and replace the hub assembly. Normal braking works but ABS will not until it is fixed.
Knock sensor codes on the V8
- What you'll notice
- Check-engine light with a knock sensor code, sometimes with slightly weaker performance or fuel economy.
- Why it happens
- The knock sensors sit in the valley under the intake manifold. Water can collect there and ruin the sensors or their wiring, the rear one most often.
- What to do
- Have the code confirmed. The fix usually means removing the intake to replace both sensors and the harness, and new intake gaskets at the same time.
4WD selector problems and Service 4WD light
- What you'll notice
- A Service 4WD message, the 4WD buttons not responding, or the truck not shifting into or out of four-wheel drive.
- Why it happens
- The dashboard 4WD switch and the transfer case encoder motor that shifts it are known weak points on these trucks.
- What to do
- Have the codes read to tell a bad switch from a bad encoder motor. Avoid relying on 4WD in bad weather until it works properly.
Clunk in the steering at low speed
- What you'll notice
- A clunk or bump felt through the steering wheel during slow turns, like in parking lots, or looseness in the steering.
- Why it happens
- The intermediate steering shaft has a sliding joint that dries out and wears. GM offered a re-grease kit, and worn shafts are replaced.
- What to do
- Have the steering shaft checked so other causes like worn tie rods are ruled out. Lubricating or replacing the shaft usually stops the clunk.
Repair prices for your 2000 GMC Sierra 1500
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace corroded brake lines and bleed brakes
- Replace fuel pump module
- Replace both knock sensors, harness and intake gaskets
- Replace blower motor resistor and connector
- Replace front wheel hub bearing assembly
- Replace transfer case encoder motor
- Replace intermediate steering shaft
- Replace with remanufactured 4L60-E transmission
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Checking the NHTSA recall database…