GMC Sierra 2500HDproblems, repair costs and recalls
Problems reported across 1996–2026. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
35 documented issues across all years, most serious first.
High-pressure diesel fuel pump fails and contaminates the fuel system
- What you'll notice
- The engine dies or won't start, often with no warning, sometimes after a long crank. It often happens around 100,000 miles.
- Why it happens
- The LML Duramax uses a Bosch CP4.2 high-pressure pump that can wear internally, especially with poor or water-contaminated fuel. When it fails it sends metal through the injectors and fuel lines.
- What to do
- Have it towed rather than cranking it repeatedly. Expect the injectors, lines and tank to need cleaning or replacing along with the pump. Use quality fuel and change fuel filters on time to lower the risk.
Duramax fuel injectors leak or crack
- What you'll notice
- White or gray smoke, rough idle, hard starting, a rising oil level that smells like diesel, or a 'balance rate' code.
- Why it happens
- The early LB7 Duramax injectors are known to crack and leak fuel into the cylinders or the oil.
- What to do
- Check the oil level and smell; fuel in the oil can wipe out the bearings. A full set of injectors is the usual fix.
Rusted brake lines can burst
- What you'll notice
- The brake pedal suddenly sinks toward the floor, a brake warning light, or wet brake fluid along the frame.
- Why it happens
- The steel brake lines run along the frame and rust through in salted-road areas. Federal regulators investigated this on GM trucks of this era.
- What to do
- Have the lines inspected on a lift every year. If any are heavily rusted, replace them before one bursts.
4-speed automatic slips or shifts hard
- What you'll notice
- Flaring revs between gears, late or harsh shifts, or loss of a gear.
- Why it happens
- The 4-speed automatics in these trucks wear their clutches and seals, and heavy loads and towing heat speed that up.
- What to do
- Check the fluid. If it slips, get it diagnosed before damage spreads; adding a cooler helps trucks that tow.
Front brake rotors can crack (recall)
- What you'll notice
- Grinding or vibration when braking; in the worst case the wheel can separate.
- Why it happens
- Some front rotors were cast from out-of-spec iron and could crack.
- What to do
- Check your VIN for open recalls. A dealer replaces the rotors free.
Trailer wiring can overheat (recall)
- What you'll notice
- A burning smell or melted wiring near the battery while towing.
- Why it happens
- Too much current through the auxiliary battery feed for the trailer harness could melt its fusible link.
- What to do
- Check your VIN for open recalls. A dealer installs a fused harness free.
Passenger front air bag inflator can rupture (recalls)
- What you'll notice
- No warning before a crash.
- Why it happens
- Takata-made passenger inflators can break apart when they deploy, sending metal fragments into the cabin. Several recalls cover these years.
- What to do
- Check your VIN for open recalls and get it fixed right away. Dealers replace the inflator free.
Roof-rail air bag inflator can come apart (recalls)
- What you'll notice
- No warning before a crash.
- Why it happens
- The end cap on the side curtain air bag inflator can come loose or the inflator can rupture when it fires.
- What to do
- Check your VIN for open recalls. Dealers replace both roof-rail air bag modules free.
Brake pedal pivot nut can loosen (recalls)
- What you'll notice
- The brake pedal feels loose or stops working properly.
- Why it happens
- The nut on the brake pedal pivot bolt could back off.
- What to do
- Check your VIN for open recalls. A dealer secures the nut free.
Software fault can switch off the front air bags (recalls)
- What you'll notice
- Usually no sign before a crash.
- Why it happens
- A software diagnostic test in the air bag module could keep the front air bags and belt pretensioners from firing.
- What to do
- Check your VIN for open recalls. A dealer reprograms the module free.
Rear fuel tank can collapse and starve the engine (recall)
- What you'll notice
- The engine stalls or loses power with fuel still showing, on trucks with the dual-tank option.
- Why it happens
- The rear tank could collapse and block fuel from transferring.
- What to do
- Check your VIN for open recalls. A dealer replaces the tank free.
Engine block heater cord can short and burn (recall)
- What you'll notice
- A burning smell or melted cord when the block heater is plugged in.
- Why it happens
- The block heater cord or terminals could short-circuit, damaging the engine and creating a fire risk.
- What to do
- Don't use the block heater until the recall is done. A dealer replaces the heater parts free.
Rear wheels can lock up from a transmission valve fault (recall)
- What you'll notice
- Harsh shifts; in rare cases the rear wheels lock for a moment while driving.
- Why it happens
- Wear in a transmission control valve can cause it to fail. A follow-up recall covers trucks that got the wrong software in the first repair.
- What to do
- Check your VIN for open recalls. A dealer installs updated software free.
10-speed automatic valve body faults
- What you'll notice
- 'Service Transmission' warning, harsh or delayed shifts, a bang on downshifts, or the truck stuck in one gear.
- Why it happens
- The valve body in the 10-speed automatic behind the Duramax can wear or fail; GM bulletin 24-NA-188 covers valve body problems.
- What to do
- Have it diagnosed promptly and ask about warranty and bulletin coverage; many cases end in valve body or transmission replacement.
Power tailgate can open by itself (recall)
- What you'll notice
- The tailgate drops open while parked, sometimes unexpectedly.
- Why it happens
- Water gets into the electric release switch and shorts it.
- What to do
- Check your VIN for open recalls. A dealer replaces the switch free.
Brake module bolts can let water in and start a fire (recall)
- What you'll notice
- Usually no warning; possible ABS warning light.
- Why it happens
- The brake pressure module bolts may not be tight, letting water in and causing a short.
- What to do
- Check your VIN. Park outside until the dealer repairs it free.
Steering gear shaft can break (recall)
- What you'll notice
- Loose or unresponsive steering.
- Why it happens
- A shaft in the steering gear can fracture and disconnect from the steering arm.
- What to do
- Check your VIN for open recalls. A dealer inspects and replaces the gear free.
DEF and NOx sensor warnings with a speed-limit countdown
- What you'll notice
- A DEF warning, 'Service Emission System' message, check engine light, and a countdown that limits speed if it isn't fixed.
- Why it happens
- The NOx sensors, DEF heater and pump on the diesel exhaust system fail over time.
- What to do
- Have the codes read soon so the truck doesn't go into limp mode. A sensor is the most common fix.
Clogged exhaust filter and fuel in the oil
- What you'll notice
- Frequent 'exhaust filter full' messages, power loss, worse fuel economy and an oil level that rises over time.
- Why it happens
- The first Duramax with a diesel particulate filter injects extra fuel to burn the filter clean. Short trips interrupt that process, so the filter clogs and some of the fuel ends up in the oil.
- What to do
- Drive at highway speed long enough to let it finish cleaning. Change oil on schedule and check whether fuel is diluting it.
Central 'spider' fuel injector misfires
- What you'll notice
- Rough idle, misfires, a check engine light, hard starts or a fuel smell.
- Why it happens
- The 5.7L Vortec V8 uses one central injector with thin lines and small poppet nozzles that clog or leak with age.
- What to do
- Have the misfire diagnosed. Replacing the spider assembly is the usual fix, often together with the intake gaskets.
Intake manifold gaskets leak coolant
- What you'll notice
- The coolant level drops, a sweet smell, crust around the intake, or milky oil.
- Why it happens
- The intake gaskets on the Vortec V8 break down and let coolant out or into the oil.
- What to do
- Don't let it overheat. Replace the gaskets soon and change the oil if coolant got into it.
Front seat bolts missing or recliner can pinch fingers (recalls)
- What you'll notice
- A front seat that feels loose, or a pinch point near the seat recliner.
- Why it happens
- Some trucks left the factory missing one or two front seat mounting bolts, and the easy-entry seat recliner had a pinch point.
- What to do
- Check your VIN for open recalls. A dealer installs bolts or a cover free.
Kinked brake booster hose (recall)
- What you'll notice
- A hard brake pedal or reduced power braking.
- Why it happens
- The brake booster vacuum hose was routed so it could kink.
- What to do
- Check your VIN for open recalls. A dealer reroutes the hose free.
Broken exhaust manifold bolts
- What you'll notice
- A ticking noise on cold start that fades as the engine warms, or an exhaust smell.
- Why it happens
- Heat cycles cause the exhaust manifold bolts on the 6.0L V8 to snap, which lets exhaust leak.
- What to do
- Have it fixed before the leak burns nearby wiring or the manifold warps. Broken bolts often need to be drilled out.
Duramax water pump leaks
- What you'll notice
- Coolant drips at the front of the engine, a dropping coolant level or a sweet smell.
- Why it happens
- The water pump seal on early Duramax engines wears and leaks.
- What to do
- Keep the coolant topped off and replace the pump before the engine overheats.
Overheating while towing
- What you'll notice
- The temperature gauge climbs on hills or when towing, sometimes with reduced power.
- Why it happens
- The LLY Duramax runs hotter than other versions, and a weak fan clutch or clogged radiator makes it worse.
- What to do
- Back off and let it cool. Clean the radiator and intercooler and check the fan clutch.
Chafed diesel engine wiring harness
- What you'll notice
- Misfire or injector codes, rough running or a no-start.
- Why it happens
- The engine harness on the LLY Duramax rubs against the valve covers and wears through.
- What to do
- Have the harness inspected and repaired before replacing injectors.
Glow plug module can overheat the glow plugs (recall)
- What you'll notice
- Hard cold starts, a glow plug light, or failed glow plugs.
- Why it happens
- The glow plug control module could keep the glow plugs powered too long and burn them out.
- What to do
- Check your VIN for open recalls. A dealer reprograms the module free.
Burned-out glow plugs from before the recall may still need replacing at your cost.
Diesel DEF and emissions warnings
- What you'll notice
- DEF quality warnings, a DEF heater fault, or a speed-limit countdown.
- Why it happens
- NOx and exhaust temperature sensors and DEF heater parts fail.
- What to do
- Have the codes read before the speed limit kicks in. Use fresh, certified DEF.
Water leaks at the rear window and cab
- What you'll notice
- Wet carpet, stains on the headliner, or water around the sliding rear window and roof marker lights.
- Why it happens
- Owners report water getting past seals at the power sliding window, roof lights and rear cab.
- What to do
- Fix it soon to avoid mold and damaged electronics. A shop water test can find the entry point.
Tire label lists the wrong rear pressure (recall)
- What you'll notice
- No symptom, but the rear tires may be run underinflated if you follow the label.
- Why it happens
- The tire label and settings show a rear pressure that is too low.
- What to do
- Check your VIN. A dealer updates software and covers the label free.
Clunk felt in the steering wheel
- What you'll notice
- A clunk or knock you feel in the wheel when turning at low speed or going over bumps.
- Why it happens
- The sliding intermediate steering shaft loses its lubrication and binds. GM issued a bulletin for it.
- What to do
- It's mostly an annoyance, but have the steering checked for loose parts. Lubricating or replacing the shaft fixes it.
Instrument cluster gauges stick or quit
- What you'll notice
- The speedometer, fuel or temperature gauges stick or drop to zero.
- Why it happens
- Small stepper motors behind each gauge fail. GM extended coverage on many of these clusters at the time.
- What to do
- A cluster repair shop can replace the motors.
Gas V8 keeps running after the key is off
- What you'll notice
- The engine keeps running for a moment after you shut it off.
- Why it happens
- Voltage feeds back through the fuel pump module; GM bulletin PIT6489 covers it.
- What to do
- Have the dealer check for the bulletin repair.
Owner's manual missing from the radio (recall)
- What you'll notice
- The electronic owner's manual isn't available on the screen.
- Why it happens
- Some trucks left the factory without the manual loaded.
- What to do
- Check your VIN. A dealer resets the radio free.
Repair prices for your GMC Sierra 2500HD
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace high-pressure pump, injectors, lines and flush fuel system
- Replace all eight fuel injectors
- Replace NOx sensor or DEF system part
- Clean diesel particulate filter and change oil
- Replace rusted brake lines (full preformed line set)
- Replace central (spider) fuel injector assembly
- Replace lower intake manifold gaskets and coolant
- Rebuild or replace 4-speed automatic
- Replace intermediate steering shaft
- Extract broken bolts, replace manifold bolts and gasket
- Rebuild instrument cluster (replace gauge stepper motors)
- Replace water pump and coolant
- Replace fan clutch and clean radiator and intercooler
- Repair or replace chafed injector wiring harness
- Replace transmission valve body or transmission
- Replace NOx sensor or DEF heater part
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Install seat bolts or recliner coverNo charge if your vehicle is included
- Replace front rotorsNo charge if your vehicle is included
- Reroute brake booster vacuum hoseNo charge if your vehicle is included
- Reprogram glow plug control moduleNo charge if your vehicle is included
- Replace trailer jumper harnessNo charge if your vehicle is included
- Replace passenger air bag inflatorNo charge if your vehicle is included
- Replace both roof-rail air bag modulesNo charge if your vehicle is included
- Secure brake pedal pivot nutNo charge if your vehicle is included
- Reprogram air bag moduleNo charge if your vehicle is included
- Replace rear fuel tankNo charge if your vehicle is included
- Replace block heater partsNo charge if your vehicle is included
- Update transmission softwareNo charge if your vehicle is included
- Replace tailgate release switchNo charge if your vehicle is included
- Replace brake pressure modulatorNo charge if your vehicle is included
- Inspect and replace steering gearNo charge if your vehicle is included
- Update software and tire labelNo charge if your vehicle is included
- Reset radioNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.