Mazda Protegeproblems, repair costs and recalls
Problems reported across 1996–2003. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
30 documented issues across all years, most serious first.
Automatic transmission shifts erratically with O/D OFF light flashing
- What you'll notice
- The automatic shifts harshly or at odd times, gets stuck in second or third gear, slips, or revs without accelerating, while the O/D OFF light flashes and the check engine light may come on.
- Why it happens
- Mazda issued bulletins for this. On 1997-1998 models a pinched wiring harness to the transmission fluid temperature sensor can cause it, and on 1999-2000 models the transmission can stop upshifting because of a fault in its control system. Worn transmissions also slip.
- What to do
- Have the transmission codes read before agreeing to a rebuild; a wiring repair or sensor may fix it. Check the fluid level and condition too.
Ignition switch can overheat (recall)
- What you'll notice
- A burning smell or smoke from the steering column, accessories that cut in and out, or in the worst case a fire, even while the car is parked.
- Why it happens
- Grease inside the ignition switch can break down and start conducting electricity, which can overheat the switch. Mazda recalled these cars in 2015 and replaces the switch for free.
- What to do
- Ask a Mazda dealer to confirm the recall applies to your VIN and get the free switch replacement. If you smell burning near the steering column, stop using the car until it is fixed.
Rear brake hose damaged at the factory (recall)
- What you'll notice
- Brake fluid leaking near the left rear wheel, a soft or sinking brake pedal, or a brake warning light.
- Why it happens
- Some left rear brake hoses were damaged during assembly and can leak, reducing braking. Mazda recalled affected cars to inspect and replace the hose.
- What to do
- Check your VIN for the recall. Any brake fluid leak needs fixing before you drive.
Water can short the radio and overheat a speaker (recall)
- What you'll notice
- The radio cuts out or smokes, or the right rear speaker gets hot, usually in hot, humid weather with the A/C running.
- Why it happens
- Water condensing in the A/C duct can drip onto the factory radio and short it, which can overheat a speaker and in rare cases start a fire. Mazda recalled about 23,000 early 1999 Proteges.
- What to do
- Check your VIN for the recall. The fix is free.
Alternator or voltage regulator failure
- What you'll notice
- Battery light on, dim or flickering lights, a battery that keeps going dead, or a car that stalls while driving.
- Why it happens
- The voltage regulator built into the alternator can fail and overcharge or undercharge, which can also ruin the battery. Alternator failures are among the most reported repairs on this car.
- What to do
- Have the battery and charging system tested. If the alternator is overcharging, replace it before it kills a new battery.
Front brake calipers stick
- What you'll notice
- The car pulls to one side when braking, a burning smell or hot wheel after driving, grinding, or pads wearing out quickly on one side.
- Why it happens
- Front calipers corrode and stick, so the pads keep rubbing. This is the most-reported problem on 2002 Proteges and the top repair in owner surveys.
- What to do
- Have the brakes inspected. A sticking caliper should be replaced with new pads, and the brake fluid flushed if it is old.
Broken engine mounts
- What you'll notice
- Heavy vibration at idle, a clunk when shifting into drive or reverse, or a jolt when you step on the gas.
- Why it happens
- The rubber engine mounts crack and wear out with age, letting the engine move too much.
- What to do
- Have the mounts checked. A broken mount is not an emergency but it strains other parts, so replace it soon.
Wheel bearing hum
- What you'll notice
- A humming or growling noise that gets louder with speed and may change when you turn.
- Why it happens
- Wheel bearings and hub assemblies wear out; owners report them often on the Protege.
- What to do
- Have it checked soon. A badly worn bearing can overheat and fail.
Hesitation and jerking when accelerating
- What you'll notice
- The car hesitates, bucks or jerks when you accelerate, may feel down on power, and the check engine light may show lean codes such as P0171.
- Why it happens
- Mazda issued bulletins for lack of power with lean-running codes and for hesitation and jerking on these years. Cracked intake air hoses, which let in unmeasured air, can cause the same symptoms.
- What to do
- Have the codes read and the intake hoses checked for cracks. Ask a dealer about the related bulletins and software.
Misfire from a failed ignition coil
- What you'll notice
- Rough running, shaking at idle, loss of power and a flashing or steady check engine light.
- Why it happens
- Mazda issued a bulletin about ignition coil failures on the 1.8L engine. Coil packs are a common Protege repair.
- What to do
- Have the misfire codes read. Do not drive far with a flashing check engine light, as it can damage the catalytic converter.
Hard starting
- What you'll notice
- The engine cranks longer than normal before it starts, especially when cold or after sitting.
- Why it happens
- Mazda issued a bulletin for hard starting on these model years.
- What to do
- Have fuel pressure, spark and sensors checked, and ask the dealer about the bulletin fix.
Radiator or water pump leak
- What you'll notice
- Coolant puddles under the front of the car, a sweet smell, the temperature gauge climbing, or low coolant.
- Why it happens
- The radiator, water pump and thermostat are common cooling system repairs on the Protege as it ages.
- What to do
- Do not drive if the engine overheats. Have the cooling system pressure tested to find the leak.
Body rust
- What you'll notice
- Bubbling paint and rust, often around the rear wheel arches and lower body.
- Why it happens
- Rust is a known weak spot on this generation, especially in states that salt the roads.
- What to do
- Treat small spots early. Have the underbody and brake lines checked for rust on older cars.
Brake warning light stays on
- What you'll notice
- The red brake warning light stays on even with the parking brake released.
- Why it happens
- Mazda issued a bulletin for this on these years. A low brake fluid level from worn pads or a leak can also turn the light on.
- What to do
- Check the brake fluid level first. If it is low, have the brakes checked for wear or a leak before driving far.
Poor engine performance
- What you'll notice
- The engine feels weak, hesitates or runs poorly.
- Why it happens
- Mazda issued a bulletin for poor engine performance on these years.
- What to do
- Have the codes read and ask a dealer about the bulletin repair. Also check the spark plugs, wires and air filter.
Clunk over bumps from worn struts or stabilizer links
- What you'll notice
- Clunking or knocking from the front or rear when going over bumps, and a bouncy or floaty ride.
- Why it happens
- Struts, stabilizer bar end links and bushings wear out and are among the most common repairs on this car. Mazda also issued a bulletin for a rear stabilizer bar clunk on 2001-2002 models.
- What to do
- Have the suspension inspected. End links and bushings are cheap fixes; worn struts should be replaced in pairs.
Check engine light from an EGR fault (P0402)
- What you'll notice
- Check engine light with code P0402 (too much exhaust gas recirculation), sometimes with rough idle.
- Why it happens
- Mazda issued bulletins for check engine lights with code P0402 on these years. EGR valves are also a common replacement on this car.
- What to do
- Have the EGR valve and its passages checked and cleaned. Ask a dealer about the bulletin repair.
High idle with check engine light (P0507)
- What you'll notice
- The engine idles too fast, often revving high right after starting, with a check engine light and code P0507.
- Why it happens
- Mazda issued a bulletin for code P0507 (idle speed higher than expected) on 2001-2003 Proteges. Dirty idle air control parts or vacuum leaks are common causes.
- What to do
- Have the idle air control valve and throttle body cleaned and check for vacuum leaks.
Rattle from the engine when cold
- What you'll notice
- A rattle from the engine area between about 1,000 and 3,000 rpm when the engine is cold.
- Why it happens
- Mazda issued a bulletin for this cold-engine rattle on 2001-2002 Proteges. Loose heat shields are another common source of rattles.
- What to do
- Have a shop pin down the source. If it fades as the engine warms up and nothing is loose, it is usually not serious.
Oil leak from the valve cover gasket
- What you'll notice
- Oil on the top or side of the engine, a burning oil smell, or oil in the spark plug wells causing a misfire.
- Why it happens
- The valve cover gasket and spark plug tube seals harden with age and leak.
- What to do
- Replace the gasket and seals; it is a fairly cheap job.
Blower fan works only on high
- What you'll notice
- The heater and A/C fan works only on the highest setting, or not at all.
- Why it happens
- The blower motor resistor, which controls the lower fan speeds, burns out.
- What to do
- Replace the blower motor resistor; it is usually an easy, cheap part.
Power door locks or door key cylinder fail
- What you'll notice
- Power locks work only some of the time, or the key is hard to put in or turn in the door or trunk lock.
- Why it happens
- Mazda issued bulletins for power door lock malfunctions and for door and trunk lock cylinders whose flaps break or bind.
- What to do
- A shop can replace the lock actuator or lock cylinder. Ask a dealer about the related bulletins.
Rotten egg smell from the exhaust
- What you'll notice
- A sulfur or rotten egg smell from the exhaust, mostly after hard acceleration or a long drive.
- Why it happens
- The catalytic converter can turn sulfur in gasoline into a smelly gas. Mazda has bulletins on this odor, and a failing catalytic converter can make it worse.
- What to do
- Try a different brand of gas. If the smell is strong or the check engine light is on, have the converter and fuel mixture checked.
Musty smell from the A/C vents
- What you'll notice
- A musty or mildew smell when the A/C first comes on.
- Why it happens
- Mold grows on the damp A/C evaporator. Mazda issued bulletins on this.
- What to do
- Have the evaporator cleaned and replace the cabin filter if fitted. Running the fan without A/C before parking helps.
Clunk or thump from the rear suspension
- What you'll notice
- A clunk or thump from the rear of the car when driving over bumps.
- Why it happens
- Mazda issued bulletins for a rear suspension clunk over bumps and a thumping noise from the rear suspension tower on these years.
- What to do
- Have the rear struts, mounts and bushings checked. It is usually not a safety issue.
Popping from the front brakes at low speed
- What you'll notice
- A pop or click from the front brakes when braking gently at low speed.
- Why it happens
- Mazda issued a bulletin for a popping noise from the front brake calipers during slow-speed braking.
- What to do
- Have the brakes inspected; lubricating or replacing the caliper slides and pad hardware usually fixes it.
Weak heat or slow engine warm-up
- What you'll notice
- The heater blows lukewarm air and the temperature gauge takes a long time to rise.
- Why it happens
- Mazda issued a bulletin for weak heat and slow warm-up. A thermostat stuck open is the usual cause.
- What to do
- Have the thermostat replaced. It also helps fuel economy and keeps the engine at the right temperature.
A/C stops working with check engine light on
- What you'll notice
- The A/C will not turn on and the check engine light is lit.
- Why it happens
- Mazda issued bulletins for an inoperative A/C with the check engine light on, and for corrosion on the power steering pressure switch that can upset the A/C.
- What to do
- Have the codes read and the A/C and power steering switches checked before replacing the compressor.
Noise from the drive shafts
- What you'll notice
- A clicking, knocking or humming noise from the front axles, often when turning or accelerating.
- Why it happens
- Mazda issued a bulletin for drive shaft noise on these years. Worn CV joints are a common cause.
- What to do
- Check the CV boots for tears and grease. A clicking joint should be replaced before it fails.
Check engine light from the EGR sensor circuit (P0400)
- What you'll notice
- Check engine light with code P0400 under certain loads and speeds.
- Why it happens
- Mazda issued a bulletin saying electrical noise in the EGR boost sensor circuit can set this code on 1995-1996 Proteges.
- What to do
- Ask a shop to check the EGR sensor wiring and the bulletin repair before replacing the EGR valve.
Repair prices for your Mazda Protege
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Diagnose transmission; repair harness or replace with used/rebuilt transmission
- Replace alternator
- Replace front calipers and pads
- Replace engine mount
- Replace stabilizer links and bushings, or struts
- Replace front wheel bearing
- Diagnose drivability; replace intake hose or sensor
- Replace ignition coil
- Clean or replace EGR valve
- Clean throttle body and idle air control valve
- Diagnose no-start/hard start and repair
- Diagnose rattle and secure or replace heat shield
- Replace radiator or water pump and refill coolant
- Replace valve cover gasket and plug tube seals
- Replace blower motor resistor
- Repair rust on rear wheel arches
- Replace door lock actuator or lock cylinder
- Diagnose fuel mixture; replace catalytic converter if failed
- Clean A/C evaporator
- Replace rear strut mounts or bushings
- Service front caliper slides and pad hardware
- Diagnose brake warning light; top up fluid or replace switch
- Replace thermostat
- Diagnose A/C and replace pressure switch
- Replace front CV axle
- Diagnose and tune up (plugs, wires, filters)
- Diagnose and repair EGR sensor wiring
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Replace ignition switchNo charge if your vehicle is included
- Inspect and replace left rear brake hoseNo charge if your vehicle is included
- Apply water shield tape over audio unitNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.