Your 2000 Mercedes-Benz CLKproblems, repair costs and recalls
What we've documented about the 2000 Mercedes-Benz CLK: problems owners and shops report, typical repair and upkeep costs, and safety recalls.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems for your 2000 Mercedes-Benz CLK
18 documented issues apply to 2000, most serious first.
Harsh shifts, limp mode or fluid leak at the transmission plug
- What you'll notice
- Hard or delayed shifts (often the 2-3 shift), slow engagement into Drive or Reverse, or the car getting stuck in 2nd gear with little power. Some cars show transmission fluid around the wiring plug on the side of the gearbox.
- Why it happens
- The 5-speed automatic uses a circuit board inside the gearbox (the conductor plate) with speed sensors that fail with age. The plug where the wiring enters the case can also leak fluid, which can creep up the harness toward the control unit. Old or low fluid makes shifting worse.
- What to do
- Have the transmission scanned for codes and check the fluid level and condition. A leaking plug is cheap to reseal; a failed conductor plate can often be replaced without rebuilding the whole gearbox.
Engine stalls or won't restart when hot (crank sensor)
- What you'll notice
- The engine cuts out while driving and then won't restart until it cools down, or it cranks for a long time before starting. Stalling at idle can happen too.
- Why it happens
- The crankshaft position sensor tells the engine computer where the crankshaft is. When it starts to fail, usually with heat, the computer loses that signal and shuts off spark and fuel.
- What to do
- If the engine stalls, get safely off the road. Have the codes read; this sensor is a common and fairly cheap part on these engines and is often the first thing to check.
ABS control unit fails
- What you'll notice
- ABS and stability control warning lights stay on, and ABS may not work in a hard stop.
- Why it happens
- The ABS control unit (modulator) can fail internally. Old brake fluid that has absorbed water is a known cause of this failure.
- What to do
- Have the codes read. The brakes still work without ABS, but drive gently and get it repaired soon. Change the brake fluid every two years to protect the new unit.
Rust, including front spring perches that can break
- What you'll notice
- Rust bubbles on fender edges, door bottoms, sills and wheel arches. If a front spring perch breaks, you may hear a loud bang or clunk and see one front corner drop, with the tire rubbing the fender.
- Why it happens
- This generation used water-based paint and had little rust protection. Salt and water attack the welds that hold the front spring perches to the inner fenders.
- What to do
- Have the body and the front spring perches inspected, especially in snowy or wet climates. A cracked perch is a safety problem and should be repaired or reinforced before more driving.
Intake manifold flaps break off
- What you'll notice
- A check engine light, rough running or a rattle from the top of the engine. In bad cases broken plastic pieces get sucked into the engine.
- Why it happens
- Plastic flaps inside the intake manifold, which change the air path for more power, get brittle with age and can break.
- What to do
- Have the intake manifold flaps inspected at high mileage, especially if you hear rattling. Fix it soon, because broken pieces can damage the engine.
Fuel pump may keep running after a crash (recall)
- What you'll notice
- No warning in everyday driving. The risk only shows up after a collision, when the fuel pump could keep running and feed a fuel leak.
- Why it happens
- A software calibration fault could leave the fuel pump powered after a crash, raising the risk of fire. Mercedes-Benz recalled affected cars (campaign 2008 070001) and reprograms the software.
- What to do
- Check the VIN for open recalls at a Mercedes-Benz dealer and have the free software update done.
Free under recall 08V303000 (Mercedes campaign 2008 070001): the dealer recodes the software. The recall lists 2003–2004 and 2006–2008 CLK-Class cars. Ask the dealer to check your VIN for open recalls.
Misfire from failing ignition coils
- What you'll notice
- Rough idle (often worst when cold), a loss of power when accelerating, a flashing or steady check engine light with misfire codes, and sometimes a fuel smell.
- Why it happens
- The ignition coils on this V6 wear out with heat and age. This engine also has two spark plugs per cylinder, so worn plugs add to the strain on the coils.
- What to do
- Have the misfire codes read to find which coil is weak. Many shops replace the coils and all 12 spark plugs together. Avoid cheap no-name coils.
Worn engine and transmission mounts
- What you'll notice
- Strong vibration in the cabin at idle, a thump when shifting into Drive or Reverse, or a clunk when you get on and off the gas.
- Why it happens
- The rubber engine and transmission mounts soften and sag with age and heat, so they no longer soak up engine movement.
- What to do
- Have the mounts checked with the hood open while someone shifts between Drive and Reverse. Replace worn mounts in pairs so the engine sits level.
Mass airflow sensor fails
- What you'll notice
- Hesitation or stumbling when accelerating, rough running, poor fuel economy and often a check engine light.
- Why it happens
- The mass airflow sensor measures the air going into the engine. Its sensing element gets dirty or fails with age, so the engine gets the wrong amount of fuel.
- What to do
- Have the codes read. Check that the air filter is clean, and fit a new filter when the sensor is replaced. Use a genuine or quality sensor.
Front control arm and thrust arm bushings crack
- What you'll notice
- Clunking from the front over bumps or when braking, vague or wandering steering, the car pulling to one side, and uneven tire wear.
- Why it happens
- The rubber bushings in the front control arms and thrust (tension) arms crack and wear out. Some are oil-filled and leak when they fail.
- What to do
- Have the front suspension inspected. Replace worn arms or bushings and then get a wheel alignment.
Worn tie rod ends and suspension joints
- What you'll notice
- Knocking or looseness in the steering, wandering on the highway, and tires wearing on the edges.
- Why it happens
- Tie rod ends, ball joints and other suspension joints wear with mileage and rough roads. Worn joints and bushings are the most common inspection failure on these cars in UK testing data.
- What to do
- Have the steering and suspension joints checked for play. Replace worn parts and get an alignment afterward.
ABS and ESP warning lights from a bad brake light switch
- What you'll notice
- The ABS, ESP or brake warning lights come on, brake lights may stay on or not work, and cruise control may stop working.
- Why it happens
- The brake light switch at the brake pedal wears out. The stability control system uses its signal, so a faulty switch turns on several warning lights at once.
- What to do
- Have the codes read before replacing larger parts. The brake light switch is cheap and quick to replace, and working brake lights matter for safety.
Fuel gauge reads wrong or fuel pump fails
- What you'll notice
- The fuel gauge reads empty after filling up, sticks at full, or jumps around; in some cases the engine stalls or won't start because the pump has failed.
- Why it happens
- The fuel level sending units in the tank wear out, and the fuel pump can fail with age. Owners of both generations report replacing these parts.
- What to do
- Use the trip meter to track fuel until the gauge is fixed so you don't run out. Have the sender and pump tested before replacing parts.
Convertible top leaks hydraulic fluid or stops working
- What you'll notice
- The top moves slowly, stops partway or won't move. You may find hydraulic fluid in the trunk or behind the rear seats, damp carpets after rain, or a soft-top warning light.
- Why it happens
- The top is moved by hydraulic rams whose seals wear out after about 15 years. Cables, position switches and a sensor in the windshield latch can also fail.
- What to do
- Don't keep cycling a top that is leaking fluid. Have a convertible specialist find the leaking ram or failed switch; rebuilding rams is often cheaper than buying new ones.
Power window regulator fails
- What you'll notice
- A window that moves slowly, makes grinding or clicking noises, drops into the door, or won't go up at all. On convertibles, a stuck window can also stop the top from working.
- Why it happens
- The window regulator uses cables and plastic slides that stretch, crack or come loose with age. The driver's window and the rear windows on convertibles wear out most.
- What to do
- If a window won't close, cover it to keep rain out and have the regulator replaced. After repair, the window and top may need to be reset with a scan tool.
Check engine light from secondary air injection faults
- What you'll notice
- A check engine light with secondary air system codes. The car usually drives normally.
- Why it happens
- The secondary air system pumps air into the exhaust for a short time after a cold start to warm up the catalytic converters. Its pump, valves and hoses fail with age.
- What to do
- Have the codes read and the system tested. It is not urgent for the engine, but the car will fail an emissions test with the light on.
Air conditioning blows warm
- What you'll notice
- Weak or warm air from the vents, or cold air only on one side.
- Why it happens
- Common causes are a refrigerant leak at the receiver-drier hose, a failed evaporator temperature sensor, a stuck blend door actuator, and on high-mileage cars a worn compressor.
- What to do
- Have the A/C system checked for leaks and codes before recharging it. Recharging without fixing a leak wastes money.
Instrument cluster display loses pixels
- What you'll notice
- Missing lines or segments in the display that shows the odometer, outside temperature and messages, making it hard to read.
- Why it happens
- The LCD screen in the instrument cluster ages and loses pixels. In some cases a burned-out backlight bulb is the real cause.
- What to do
- Check the backlight bulbs first. A cluster repair specialist can usually fix the display for less than a new cluster.
Repair prices for your 2000 Mercedes-Benz CLK
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace transmission conductor plate and plug adapter, refill fluid
- Replace crankshaft position sensor
- Replace ignition coils and spark plugs (12 plugs)
- Replace engine mounts (pair)
- Replace mass airflow sensor
- Replace front control arm or thrust arm (with bushings), then align
- Replace tie rod ends, then align
- Replace window regulator and motor
- Replace brake light switch
- Replace ABS control module
- Replace secondary air injection control valve
- Replace fuel pump and fuel level sending unit
- Replace A/C evaporator temperature sensor and recharge
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Recall repair at a Mercedes-Benz dealer (software reprogramming)No charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Checking the NHTSA recall database…