Mercedes-Benz S-Classproblems, repair costs and recalls
Problems reported across 1996–2025. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
33 documented issues across all years, most serious first.
Air suspension (Airmatic) sagging overnight
- What you'll notice
- One corner or one end of the car sits low after parking, the car is slow to rise after starting, a 'Car too low' or suspension warning appears, or the ride turns harsh and bouncy.
- Why it happens
- The rubber air springs in the Airmatic struts crack and leak with age, usually after 60,000 to 100,000 miles. Torn dust boots let dirt in and speed this up, and the rear springs often go first. A faulty rear height sensor can also make the rear drop.
- What to do
- Don't drive far if the car is sitting on its bump stops or a 'Stop vehicle' message shows. Have the leaking strut found with a leak test and replaced quickly, because a leak makes the compressor overwork and fail too.
Active Body Control (ABC) hydraulic leak or pump failure
- What you'll notice
- An ABC warning message, a corner that drops quickly, a hard or bouncy ride, too much body lean, red hydraulic fluid under the car, or a howl from the engine bay at low revs. Applies to S600, AMG and other cars ordered with ABC.
- Why it happens
- The ABC system uses high-pressure hydraulic fluid instead of air. Its hoses and seals age, the pressure accumulators wear out after about 10 years or 60,000 miles, and neglected fluid wears the pump, valve blocks and struts.
- What to do
- Stop and check the fluid level if a red ABC warning appears; driving with a burst hose can run the pump dry. Have a specialist read the ABC fault log and check the fluid condition before replacing parts.
ABC suspension high-pressure hose can corrode and leak (recall)
- What you'll notice
- Hydraulic fluid leaking near the front of the car, an ABC warning, or the car sinking and riding harshly.
- Why it happens
- The steel inner layer of an ABC high-pressure hose could corrode from humidity and start leaking fluid. Mercedes recalled affected cars with Active Body Control to fit a corrosion-resistant hose.
- What to do
- Ask a Mercedes dealer to check your VIN for open recall work. If fluid is leaking, have the car towed rather than driven.
Engine wiring harness insulation crumbling
- What you'll notice
- Loss of power when pulling away, rough idle, stalling, misfires or a car that won't start.
- Why it happens
- Engine harnesses built before January 1996 used insulation that breaks down with heat and age, letting wires short. Early 1996 cars may still have the old harness; Mercedes changed it during 1996 production.
- What to do
- Ask whether the harness has been replaced. If not, have a mechanic inspect the wiring at the engine; replacing the harness is the lasting fix.
Worn timing idler gear (5.5L V8)
- What you'll notice
- Check engine light with camshaft position or timing codes, rough running, or a rattle or ticking from the front of the engine.
- Why it happens
- On early 5.5L V8 engines, a timing-drive idler gear made of too-soft metal wears its teeth, which upsets cam timing. A class-action settlement once extended coverage, but it has now expired for nearly all cars.
- What to do
- Get the timing codes checked promptly. If the gear wears too far the chain can jump, which can damage the engine. The repair is big, so get a Mercedes specialist's quote.
Transmission stuck in limp mode (conductor plate or control unit)
- What you'll notice
- The transmission stops shifting and stays in one gear, with a warning message, often after a restart it works again for a while.
- Why it happens
- The 7-speed automatic's electronics fail: the control unit, the conductor plate inside the valve body, or the valve body itself.
- What to do
- Have the transmission codes read. A new control unit must be coded to the car; specialists can repair or reprogram units for less than the dealer.
Hybrid inverter failure leaves car unable to start
- What you'll notice
- The car won't start at all and shows hybrid system warnings.
- Why it happens
- The inverter/converter that manages the hybrid system can fail. New parts are scarce and expensive.
- What to do
- Have the hybrid system scanned by a dealer or hybrid specialist. On a high-mileage car, compare the repair cost with the car's value before going ahead.
Timing chain rattle on cold start (twin-turbo V8)
- What you'll notice
- A metallic rattle for a few seconds after a cold start, then possibly long cranking, misfires, power loss and a check engine light.
- Why it happens
- Oil drains from the timing tensioner overnight, so the chain is briefly slack at start-up. Over time this stretches the chains and wears guides. Early production engines were affected most; Mercedes later revised parts.
- What to do
- Don't ignore a cold-start rattle. Have a specialist check cam timing values; replacing tensioners early is far cheaper than repairing a chain that jumps.
Engine oil plugs may leak under high load (recall)
- What you'll notice
- An oil leak, a burning oil smell or a low oil warning.
- Why it happens
- Two engine oil plugs might not hold under high engine load. Leaking oil can reach hot parts and start a fire. Mercedes recalled S560s to add a retaining plate.
- What to do
- Ask the dealer to confirm by VIN whether the recall repair was completed. Stop driving if you smell burning oil.
Drive shaft joint can break (recall)
- What you'll notice
- Vibration or clunking from under the car, or a sudden loss of drive power. Applies to 4MATIC all-wheel-drive S450 and S560 models.
- Why it happens
- A universal joint in the drive shaft can break. Mercedes recalled affected 4MATIC cars to inspect and replace the drive shaft.
- What to do
- Check your VIN for this recall and book the free inspection. Pull over safely if you feel new vibration from under the car.
Engine may stall or overheat from Camtronic fault (recall)
- What you'll notice
- An engine warning light, the engine overheating, or the engine suddenly stalling.
- Why it happens
- If the Camtronic variable valve lift part fails mechanically, the engine computer software could react in a way that overheats or stalls the engine. A separate 2021 software recall also fixed a stalling fault on S580s.
- What to do
- Have a dealer confirm both software updates were done. If the engine warning light comes on, have it checked before long drives.
Fuel pump can fail and stall the engine (recall)
- What you'll notice
- The engine stalls or won't restart.
- Why it happens
- A nozzle on the fuel tank's suction jet pump could be loose or missing, which can make the fuel pump fail. Mercedes recalled 2021 S580s for this.
- What to do
- Check your VIN for open recalls and have the free repair done.
Front brake hoses can rupture (recall)
- What you'll notice
- A brake fluid warning, a soft or sinking brake pedal, longer stopping distances, or fluid at a front wheel.
- Why it happens
- The front brake hoses could rupture and leak brake fluid. Mercedes first recalled 2021 to 2023 cars and later expanded the recall to more S-Class models.
- What to do
- Check your VIN for open recalls. If the brake warning lights up or the pedal feels soft, stop and have the car towed.
High-voltage starter generator unit can fail (recall)
- What you'll notice
- Sudden loss of drive power with warning messages.
- Why it happens
- A software error could make the control unit for the high-voltage starter alternator fail. Mercedes fixed it with a software update.
- What to do
- Check your VIN for this recall and have the update done.
Air suspension compressor running constantly or burned out
- What you'll notice
- A loud humming from behind the front bumper that runs a long time, the car taking ages to lift, or the car staying down with a 'Vehicle too low' warning.
- Why it happens
- The compressor wears internally and can no longer build enough pressure. It usually fails early because a leaking air spring or valve block made it run far longer than it was designed to. A stuck relay can also keep it running until it burns out.
- What to do
- Find and fix any air leak before or at the same time as replacing the compressor, or the new one will fail too. Ask the shop to replace the compressor relay as well.
Rust on body panels and subframe
- What you'll notice
- Bubbling paint or rust on door bottoms, wheel arches, the trunk lid, or rust on the subframe underneath.
- Why it happens
- Mercedes used a water-based paint and steel with weak corrosion protection in this era, and the body was not fully galvanized until early 2003. The 2007 to 2009 cars can also rust in salted-road areas; later cars are better protected.
- What to do
- Have the underside and subframe inspected, especially before buying. Treat small spots early; structural rust on the subframe is a bigger and more expensive job.
Broken coil spring or worn subframe bushings
- What you'll notice
- A clunk over bumps, one corner sitting lower than the others, a harsh ride, or the car feeling loose and wandering.
- Why it happens
- This is a very heavy car. Front springs can snap at the bottom and rear springs at the top, and the rubber subframe bushings wear out at higher mileage.
- What to do
- Have the suspension inspected on a lift. A broken spring can damage a tire, so replace it promptly; spring jobs on this car need proper spring compressors.
Plastic camshaft oil tubes break
- What you'll notice
- Ticking or clatter from the top of the engine, and in bad cases worn camshafts.
- Why it happens
- The V8s spray oil onto the camshafts through plastic tubes (cam oilers) that turn brittle with heat and can break, starving the cam lobes of oil.
- What to do
- Have the valve covers removed and the oil tubes checked. Owners recommend replacing them with metal versions.
Transmission fluid leak at the electrical plug
- What you'll notice
- Red fluid dripping from the side of the transmission, low fluid, or erratic shifting and limp mode.
- Why it happens
- The 5-speed automatic has an electrical connector that passes through the case. Its plastic adapter and O-rings harden and leak fluid.
- What to do
- Have the connector adapter and seals replaced and the fluid topped up. This is a cheap part; don't ignore it, because low fluid damages the transmission.
Sluggish shifts or torque converter shudder
- What you'll notice
- Slow, lazy gear changes, a shudder at steady speed, or harsh shifts. Reverse may be the first gear to fail.
- Why it happens
- The 5-speed automatic had no set fluid-change interval, so many have old, worn fluid. 2000 to 2002 cars in particular drew complaints about slow responses and converter shudder.
- What to do
- Have the fluid and filter changed with the correct Mercedes fluid if there are no records, then recheck. If problems remain, get a transmission diagnosis before a rebuild.
Crankshaft position sensor failure
- What you'll notice
- The engine stalls while driving, cranks but won't start (often when hot), or runs rough with a check engine light.
- Why it happens
- The crankshaft position sensor tells the engine computer when to fire. Heat breaks it down over time and it stops sending a signal.
- What to do
- Have the codes read. The sensor is inexpensive and a common cause of no-starts on these cars.
Water leaking into cabin or trunk
- What you'll notice
- Wet carpets, water in the trunk spare-tire well, a damp smell, fogged windows, or electrical faults after rain.
- Why it happens
- The sunroof drain tubes clog with debris and overflow, and taillight seals can let water into the trunk. Water then reaches modules and wiring.
- What to do
- Clear the sunroof drains and check the taillight seals. Dry the carpets quickly and have any wet modules checked before they corrode.
Blower motor regulator can overheat (recall)
- What you'll notice
- The fan stops working or a hot plastic or burning smell comes from the passenger footwell.
- Why it happens
- A circuit defect in the blower motor regulator could make it overheat and melt or burn nearby parts. Mercedes recalled affected cars to replace it.
- What to do
- Ask a Mercedes dealer to confirm the recall was done. If you smell burning, turn the fan off and get it checked.
V12 misfire from ignition coils or spark plugs
- What you'll notice
- Rough idle, shaking, misfires and a flashing or steady check engine light.
- Why it happens
- The V12s have 24 spark plugs and coil packs that each fire six cylinders. These wear out, and the tight engine bay makes the work slow and costly.
- What to do
- Have the misfire codes read. Don't drive long with a flashing check engine light, as unburned fuel can damage the catalytic converters.
Climate blower motor stops working
- What you'll notice
- The fan works only some of the time, then stops completely, so there is no air from the vents for A/C or heat.
- Why it happens
- Moisture gets into the blower motor and it fails.
- What to do
- Have the blower motor tested. Replacement takes up to about two hours.
Valve cover oil leak and burning oil smell
- What you'll notice
- A burning oil smell after driving, light smoke from the engine bay, or oil spots on the turbochargers.
- Why it happens
- Heat warps the plastic valve covers so their gaskets no longer seal, and oil drips onto the hot turbos.
- What to do
- Have the leak confirmed. Replacing the valve covers, not only the gaskets, is usually needed. Oil on hot turbos is a fire risk, so don't put it off.
Harsh or clunky gear changes
- What you'll notice
- Hard upshifts or downshifts, especially between 2nd and 3rd gear.
- Why it happens
- Worn transmission fluid or a conductor plate that has lost its calibration. Mercedes' long fluid interval leaves many cars with old fluid.
- What to do
- Ask for any software updates, then a fluid and filter change with an adaptation reset. If that fails, the conductor plate may need replacing.
Battery goes flat after the car sits
- What you'll notice
- The battery is dead after a few days to a week parked, or the Mercedes app keeps sending low battery warnings.
- Why it happens
- A control module, such as the infotainment, keyless entry or driver-assist units, fails to go to sleep and keeps drawing power.
- What to do
- Have a shop measure the parked current draw to find the module that stays awake. Use a battery maintainer if the car sits for more than a week.
Emergency call (eCall) may not work (recall)
- What you'll notice
- An SOS or emergency call warning may show, or there may be no sign at all. After a crash the system might not call or might send the wrong location.
- Why it happens
- Software problems in the communication module and its SIM card could disable the emergency call system or send an incorrect location. Mercedes fixed this with software updates.
- What to do
- Make sure the software update was done, either over the air or at a dealer. Check your VIN for open recalls.
Power windows or door locks stop working
- What you'll notice
- A window won't go up or down, moves slowly, or a door won't lock or unlock with the key fob, most often the driver's door.
- Why it happens
- The heavy double-pane glass wears out window motors and regulators on older cars. Door control modules can corrode or fail internally, and lock actuators wear out.
- What to do
- Have the door panel removed and the regulator, motor, lock actuator or door module tested. Some door module repairs need a Mercedes-level scan tool to code the new part.
Central locking, trunk and seat functions fail (vacuum pump)
- What you'll notice
- The central locking, trunk release, lumbar support, rear parking guide rods or heater flaps stop working, or a pump keeps buzzing in the trunk.
- Why it happens
- One vacuum/pressure pump (the PSE pump) runs many comfort features on this generation. Its motor wears out and its hoses crack and leak.
- What to do
- Have the PSE pump and its hoses tested for leaks. A leak can make the pump run until it fails, so fixing the hose early is cheaper.
Flush door handles don't respond or open on their own
- What you'll notice
- The pop-out door handles don't extend when touched, are hard to pull, or open and close unexpectedly.
- Why it happens
- Owners report the electric flush handles misbehave; the cause hasn't been pinned down publicly. Some found locking the car and walking away with the key stops it.
- What to do
- Report it to the dealer under warranty and ask about software updates for the door control units.
Clicking noise from dashboard
- What you'll notice
- A clicking sound from the middle top of the dashboard or near the passenger seat, often when turning over uneven roads.
- Why it happens
- Owners of newer cars report interior clicks that dealers have struggled to find. The cause isn't confirmed.
- What to do
- Record the noise on your phone and show the dealer while the car is under warranty.
Repair prices for your Mercedes-Benz S-Class
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace one leaking Airmatic air strut
- Replace Airmatic compressor and relay
- Repair ABC leak (hose, accumulator or strut) or replace ABC pump
- Body rust repair or subframe rust treatment
- Replace window regulator/motor or door lock actuator
- Replace PSE vacuum/pressure pump or repair leaking hose
- Replace coil springs (pair) or subframe bushings
- Replace engine wiring harness
- Replace cam oiler tubes with metal versions
- Replace transmission connector adapter and seals, top up fluid
- Transmission fluid and filter service (torque converter if needed)
- Replace crankshaft position sensor
- Clear sunroof drains and reseal taillights
- Replace V12 spark plugs and failed coil packs
- Replace timing idler gear, chain and related parts
- Replace conductor plate or transmission control unit and code it
- Replace blower motor
- Replace hybrid inverter/converter assembly
- Replace timing chain tensioners (chains, guides and sprockets if stretched)
- Replace both valve covers and gaskets
- Transmission fluid and filter service with adaptation reset (conductor plate if needed)
- Parasitic drain test and battery or module replacement
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Replace ABC high-pressure hose under recallNo charge if your vehicle is included
- Replace blower motor regulator under recallNo charge if your vehicle is included
- Install retaining plate on engine oil plugs under recallNo charge if your vehicle is included
- Inspect and replace drive shaft under recallNo charge if your vehicle is included
- Communication module software update under recallNo charge if your vehicle is included
- Engine control unit software update under recallNo charge if your vehicle is included
- Fuel pump repair under recallNo charge if your vehicle is included
- Replace front brake hoses under recallNo charge if your vehicle is included
- Control unit software update under recallNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.