Your 1998 Mercury Mountaineerproblems, repair costs and recalls
What we've documented about the 1998 Mercury Mountaineer: problems owners and shops report, typical repair and upkeep costs, and safety recalls.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems for your 1998 Mercury Mountaineer
13 documented issues apply to 1998, most serious first.
Automatic transmission slips or fails
- What you'll notice
- Late or harsh shifts, the engine revving between gears, a flashing overdrive (O/D) light, slipping, or the truck refusing to move in drive or reverse.
- Why it happens
- The four- and five-speed automatics in these years wear internally, and transmission failure is the most-reported problem on the 2002 Mountaineer. Owners commonly report rebuilds between 70,000 and 140,000 miles.
- What to do
- Check the fluid level and smell. If it slips or the O/D light flashes, have the codes read right away and avoid towing or hard driving until it is diagnosed.
Timing chain rattle on the 4.0L V6
- What you'll notice
- A rattle or buzzing from the engine for a few seconds after a cold start, or a constant rattle at idle. A check engine light for a misfire or cam timing code may follow.
- Why it happens
- The 4.0L SOHC V6 uses three timing chains with plastic guides and tensioners that wear out. The rear chain sits at the back of the engine, so the repair is very labor-heavy.
- What to do
- Do not ignore the rattle. Have a shop confirm which chain is noisy. If a chain or guide breaks, the engine can be badly damaged.
Worn ball joints
- What you'll notice
- Clunking over bumps, loose or wandering steering, or uneven tire wear on the front tires.
- Why it happens
- The front ball joints wear on these heavy SUVs and are among the most common repairs reported by owners.
- What to do
- Have the front end checked for play. A badly worn ball joint can separate and cause loss of control, so do not delay.
Cruise control switch can start a fire (recall)
- What you'll notice
- Usually no warning. In rare cases, smoke or fire near the brake master cylinder, even with the engine off.
- Why it happens
- The speed control deactivation switch can leak brake fluid internally and overheat (recalls 07V-336 and 09V-399).
- What to do
- Ask a Ford or Lincoln dealer to check your VIN for open recalls. If the repair was never done, it is free under the recall.
Free at a Ford dealer if the recall work was never done.
Firestone tire tread can separate (recall)
- What you'll notice
- Vibration, a thumping noise, or a sudden tire blowout at highway speed.
- Why it happens
- Certain Firestone tires on these trucks could lose their tread (recall 00T-005). Most were replaced long ago, but check any old spare.
- What to do
- Ask a Ford or Lincoln dealer to check your VIN for open recalls. If the repair was never done, it is free under the recall.
Free at a Ford dealer if the recall work was never done.
Throttle may stick or not return to idle (recall)
- What you'll notice
- The engine stays at higher speed when you lift off the gas or after cruise control turns off, so the truck takes longer to stop.
- Why it happens
- Problems with the speed control cable, throttle return and accelerator pedal were covered by several recalls (97V-074, 99V-062, 03V-280 and 00V-422).
- What to do
- Ask a Ford or Lincoln dealer to check your VIN for open recalls. If the repair was never done, it is free under the recall.
Free at a Ford dealer if the recall work was never done.
Wheel bearing or hub failure
- What you'll notice
- A humming or growling noise that gets louder with speed or when turning, play in the wheel, or an ABS light.
- Why it happens
- The wheel hubs and bearings are the most-reported repair on the Mountaineer in TrueDelta's survey, front and rear.
- What to do
- Have a shop check for play and noise at each wheel. Replace a worn hub soon, as a failing bearing can overheat or let the wheel wobble.
A/C stops blowing cold
- What you'll notice
- Warm or barely cool air from the vents, or the A/C compressor won't engage.
- Why it happens
- Slow refrigerant leaks and worn or seized compressors are common as these trucks age.
- What to do
- Have the system leak-tested before recharging. A seized compressor usually needs a new drier and a system flush too.
Misfire from a failed ignition coil
- What you'll notice
- Check engine light (sometimes flashing), rough idle, shaking or loss of power, especially when climbing hills.
- Why it happens
- Ignition coils fail with age and heat, often along with worn spark plugs.
- What to do
- Have the misfire code read. A flashing check engine light means stop driving hard to protect the catalytic converter.
Alternator stops charging
- What you'll notice
- Battery light on, dimming lights, a dead battery, or the truck dies while driving.
- Why it happens
- The alternator wears out, and it is one of the more common repairs in TrueDelta's survey.
- What to do
- Have the charging system tested before replacing the battery.
Clunking from worn sway bar links and bushings
- What you'll notice
- A rattle or clunk from the front over small bumps or rough roads.
- Why it happens
- The stabilizer (sway) bar end links and bushings wear and loosen.
- What to do
- Have the links checked. They are a low-cost fix, but replace them before they break.
Heat stuck on hot or clicking behind the dash
- What you'll notice
- The temperature won't change, heat blows when you want A/C, or you hear clicking behind the dash.
- Why it happens
- The blend door or its small electric actuator breaks, so the system can't mix hot and cold air.
- What to do
- Have the actuator tested. It is often reachable behind the dash or glovebox.
Squeal from the belt tensioner or idler pulley
- What you'll notice
- A squeal, chirp or grinding noise from the front of the engine, often worse at startup.
- Why it happens
- The serpentine belt tensioner and idler pulley bearings wear out.
- What to do
- Have the pulleys spun by hand to find the bad one. If it seizes, the belt can come off and you lose charging and steering assist.
Repair prices for your 1998 Mercury Mountaineer
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Rebuild or replace automatic transmission
- Replace timing chains, guides and tensioners
- Replace wheel hub and bearing assembly (one wheel)
- Replace front ball joints (one side)
- Replace sway bar end links and bushings
- Replace blend door actuator
- Replace A/C compressor, drier and recharge
- Replace one ignition coil and spark plug
- Replace belt tensioner and idler pulley
- Replace alternator
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Install fused wiring harness or disconnect speed control deactivation switchNo charge if your vehicle is included
- Replace affected tiresNo charge if your vehicle is included
- Inspect and replace speed control cable or accelerator partsNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Checking the NHTSA recall database…