Your 2004 Mercury Mountaineerproblems, repair costs and recalls
What we've documented about the 2004 Mercury Mountaineer: problems owners and shops report, typical repair and upkeep costs, and safety recalls.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems for your 2004 Mercury Mountaineer
18 documented issues apply to 2004, most serious first.
Automatic transmission slips or fails
- What you'll notice
- Late or harsh shifts, the engine revving between gears, a flashing overdrive (O/D) light, slipping, or the truck refusing to move in drive or reverse.
- Why it happens
- The four- and five-speed automatics in these years wear internally, and transmission failure is the most-reported problem on the 2002 Mountaineer. Owners commonly report rebuilds between 70,000 and 140,000 miles.
- What to do
- Check the fluid level and smell. If it slips or the O/D light flashes, have the codes read right away and avoid towing or hard driving until it is diagnosed.
Timing chain rattle on the 4.0L V6
- What you'll notice
- A rattle or buzzing from the engine for a few seconds after a cold start, or a constant rattle at idle. A check engine light for a misfire or cam timing code may follow.
- Why it happens
- The 4.0L SOHC V6 uses three timing chains with plastic guides and tensioners that wear out. The rear chain sits at the back of the engine, so the repair is very labor-heavy.
- What to do
- Do not ignore the rattle. Have a shop confirm which chain is noisy. If a chain or guide breaks, the engine can be badly damaged.
Worn ball joints
- What you'll notice
- Clunking over bumps, loose or wandering steering, or uneven tire wear on the front tires.
- Why it happens
- The front ball joints wear on these heavy SUVs and are among the most common repairs reported by owners.
- What to do
- Have the front end checked for play. A badly worn ball joint can separate and cause loss of control, so do not delay.
Shifter breaks and won't move out of gear
- What you'll notice
- The column gear shifter snaps or goes limp when shifting, leaving the truck stuck in Park, Drive or Reverse.
- Why it happens
- Parts inside the steering column that link the shifter to the transmission break. Dealers have replaced the whole column.
- What to do
- Do not drive if you cannot shift into Park. Have it towed and ask a shop whether a used column or a repair kit will fix it.
Plastic intake manifold cracks and leaks coolant
- What you'll notice
- Coolant on top of the engine or dripping at the front, low coolant, overheating, or a sweet smell.
- Why it happens
- The 4.6L V8's all-plastic intake manifold has a coolant passage at the front that cracks, a well-known problem with this engine.
- What to do
- Watch the temperature gauge and top up coolant. Replace the manifold with Ford's revised design with an aluminum coolant crossover.
Spark plug blows out of the cylinder head
- What you'll notice
- A sudden loud popping or ticking, a misfire and check engine light, and the coil on that cylinder may be damaged.
- Why it happens
- The 2-valve 4.6L V8 has only a few threads holding each spark plug in the aluminum head, and a plug can strip them and shoot out.
- What to do
- Shut the engine off and have it towed. A shop can usually repair the threads with an insert without removing the head.
Cracked thermostat housing
- What you'll notice
- Coolant seeping or dripping near the top front of the engine, low coolant, or the engine running hot.
- Why it happens
- The plastic thermostat housing can crack with age and heat cycles.
- What to do
- Check the coolant level often and have the housing inspected for wetness or white crust. Replace the housing and thermostat together.
Wheel bearing or hub failure
- What you'll notice
- A humming or growling noise that gets louder with speed or when turning, play in the wheel, or an ABS light.
- Why it happens
- The wheel hubs and bearings are the most-reported repair on the Mountaineer in TrueDelta's survey, front and rear.
- What to do
- Have a shop check for play and noise at each wheel. Replace a worn hub soon, as a failing bearing can overheat or let the wheel wobble.
Rear differential leaks or fails
- What you'll notice
- Gear oil drips at the rear axle or wheels, a whine or howl from the rear, or clunking.
- Why it happens
- Axle seals and pinion bearings in the rear differential wear and leak. If the oil runs low, the gears can fail.
- What to do
- Check the rear axle oil level and fix seal leaks early. Have a whine diagnosed before it turns into a full differential rebuild.
A/C stops blowing cold
- What you'll notice
- Warm or barely cool air from the vents, or the A/C compressor won't engage.
- Why it happens
- Slow refrigerant leaks and worn or seized compressors are common as these trucks age.
- What to do
- Have the system leak-tested before recharging. A seized compressor usually needs a new drier and a system flush too.
Misfire from a failed ignition coil
- What you'll notice
- Check engine light (sometimes flashing), rough idle, shaking or loss of power, especially when climbing hills.
- Why it happens
- Ignition coils fail with age and heat, often along with worn spark plugs.
- What to do
- Have the misfire code read. A flashing check engine light means stop driving hard to protect the catalytic converter.
Alternator stops charging
- What you'll notice
- Battery light on, dimming lights, a dead battery, or the truck dies while driving.
- Why it happens
- The alternator wears out, and it is one of the more common repairs in TrueDelta's survey.
- What to do
- Have the charging system tested before replacing the battery.
Clunking from worn sway bar links and bushings
- What you'll notice
- A rattle or clunk from the front over small bumps or rough roads.
- Why it happens
- The stabilizer (sway) bar end links and bushings wear and loosen.
- What to do
- Have the links checked. They are a low-cost fix, but replace them before they break.
Cracked liftgate panel below the rear window
- What you'll notice
- A crack in the painted panel on the liftgate below the rear glass, sometimes growing the full height of the panel, and water getting inside.
- Why it happens
- The liftgate's plastic outer panel cracks with age and heat. Body shops say it is very common on this generation.
- What to do
- Ask a Ford dealer whether any coverage applies. Otherwise, a body shop can replace the panel; seal the crack meanwhile to keep water out.
Door ajar light stays on and dome lights flicker
- What you'll notice
- The door-ajar warning stays on or chimes with doors closed, interior lights flicker or won't turn off, locks cycle on their own, or the alarm goes off.
- Why it happens
- A worn door-ajar switch inside one of the door latches sends false signals. It can drain the battery overnight.
- What to do
- Have a shop find which door reports open; the fix is usually a door latch or switch on that door.
Heat stuck on hot or clicking behind the dash
- What you'll notice
- The temperature won't change, heat blows when you want A/C, or you hear clicking behind the dash.
- Why it happens
- The blend door or its small electric actuator breaks, so the system can't mix hot and cold air.
- What to do
- Have the actuator tested. It is often reachable behind the dash or glovebox.
Squeal from the belt tensioner or idler pulley
- What you'll notice
- A squeal, chirp or grinding noise from the front of the engine, often worse at startup.
- Why it happens
- The serpentine belt tensioner and idler pulley bearings wear out.
- What to do
- Have the pulleys spun by hand to find the bad one. If it seizes, the belt can come off and you lose charging and steering assist.
Power window drops into the door
- What you'll notice
- A window stops working, moves slowly, or falls down into the door.
- Why it happens
- The window regulator cable or motor fails, or the master switch on the driver's door wears out.
- What to do
- Tape the glass up if needed and have the regulator and motor checked.
Repair prices for your 2004 Mercury Mountaineer
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Rebuild or replace automatic transmission
- Replace timing chains, guides and tensioners
- Replace thermostat housing and thermostat
- Replace wheel hub and bearing assembly (one wheel)
- Replace front ball joints (one side)
- Replace sway bar end links and bushings
- Replace liftgate applique panel and paint
- Replace steering column (used or new)
- Replace door latch with ajar switch (one door)
- Replace intake manifold and gaskets
- Repair spark plug threads with insert and replace coil
- Replace rear axle seals and refill gear oil
- Replace blend door actuator
- Replace A/C compressor, drier and recharge
- Replace one ignition coil and spark plug
- Replace belt tensioner and idler pulley
- Replace alternator
- Replace window regulator and motor (one door)
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Checking the NHTSA recall database…