Ram 1500problems, repair costs and recalls
Problems reported across 1996–2026. Pick your model year below to see what applies to your vehicle. Sold as Dodge Ram 1500 through 2010.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
33 documented issues across all years, most serious first.
Automatic transmission slipping or failing (46RE/47RE)
- What you'll notice
- Slipping, harsh or delayed shifts, loss of overdrive, a clunk going into gear, or fluid leaks, often after towing.
- Why it happens
- The four-speed automatics in these trucks have weak spots in the torque converter, overdrive and reverse parts, and cooler lines, and they handle heat and heavy loads poorly.
- What to do
- Stop towing and have the transmission diagnosed right away. Keep the fluid fresh; a rebuild with upgraded parts is the usual fix once it slips.
Overheating and head gasket failure (4.7L)
- What you'll notice
- Temperature gauge climbing, coolant loss, white exhaust smoke, or milky oil.
- Why it happens
- The 4.7L does not tolerate overheating well; a clogged or cracked radiator or low coolant can lead to blown head gaskets or cracked heads.
- What to do
- Pull over and shut the engine off if it overheats. Keep the cooling system in good shape and fix leaks right away.
Hemi lifter and camshaft wear (Hemi tick)
- What you'll notice
- A ticking noise from the engine that does not go away as it warms, then misfires and a check engine light.
- Why it happens
- Roller lifters can fail and wipe the camshaft lobes, especially on engines that use cylinder deactivation.
- What to do
- Have it diagnosed promptly. Driving with a failed lifter spreads metal through the engine and turns a lifter job into a much larger repair.
Truck can roll out of Park (recall)
- What you'll notice
- The column shifter can be moved out of Park without pressing the brake, so the truck may roll away.
- Why it happens
- A pin in the brake-shift interlock can stick, defeating the brake-pedal requirement.
- What to do
- Check your VIN for the recall and get it done. Always set the parking brake until it is repaired.
Power-locking tailgate can open while driving (recall)
- What you'll notice
- The tailgate opens on its own, sometimes while moving, and cargo can fall out.
- Why it happens
- Parts in the power tailgate lock can crack or bind, letting the latch release.
- What to do
- Check your VIN for the recalls and have the repair done. Do not carry loose cargo against the tailgate until then.
EcoDiesel EGR cooler can crack (recall)
- What you'll notice
- Coolant loss, white smoke, or a sweet smell. In the worst case a fire can start under the hood.
- Why it happens
- The EGR cooler can crack, letting coolant into the hot intake and exhaust gas path.
- What to do
- Check your VIN for the recall and have it completed. Stop driving and have it towed if you see smoke or coolant loss.
EcoDiesel high-pressure fuel pump failure (recalls)
- What you'll notice
- The engine stalls while driving, cranks without starting, or loses power.
- Why it happens
- The high-pressure fuel pump can wear internally and stop delivering fuel, which can also scatter metal through the fuel system.
- What to do
- Check your VIN for the recall that covers your year and have it done. A stall at speed is dangerous, so do not delay.
EcoDiesel crankshaft tone wheel can come apart (recall)
- What you'll notice
- The engine stalls without warning and may not restart.
- Why it happens
- The ring the crank sensor reads can separate from the crankshaft, so the computer loses its timing signal.
- What to do
- Check your VIN for the recalls and have the repair done.
Side curtain airbag inflator can rupture (recall)
- What you'll notice
- Usually no warning. The concern shows up only if the curtain airbag deploys.
- Why it happens
- A manufacturing defect can let the curtain airbag inflator break apart when it fires, which can throw metal pieces.
- What to do
- Check your VIN for the recalls and have the repair done as soon as parts are available.
Loss of power steering assist (recalls)
- What you'll notice
- Steering suddenly becomes very heavy, often with a warning light, especially at low speed.
- Why it happens
- A loose ground connection or a short in the electric steering gear can cut power assist.
- What to do
- Check your VIN for both recalls and have them done. Steering is still possible but takes much more effort, so drive carefully until it is fixed.
Engine stall from computer software (recall)
- What you'll notice
- The engine stalls while driving or at a stop.
- Why it happens
- Engine computer software could command the wrong fuel mixture under some conditions.
- What to do
- Check your VIN for the recall; the fix is a software update at the dealer.
Free under recall 23V-265. Check the VIN first.
Second row seat belt anchors may not be properly attached
- What you'll notice
- Nothing looks wrong, but the center or left rear belt anchor can pull loose in a crash.
- Why it happens
- The anchor bolts for the second row buckles may not have been installed correctly at the factory.
- What to do
- Check the VIN for recall 26V-495 and have the anchors reattached. Until then avoid seating passengers in those positions.
Free under recall 26V-495. Check the VIN first.
Steering column module weld can stop the driver airbag working
- What you'll notice
- There is no outward sign, though the airbag warning light may come on.
- Why it happens
- A weld in the steering column module may be faulty, which can break the connection the driver airbag needs to fire.
- What to do
- Check the VIN for recall 24V-199 and have the module replaced. Do not ignore an airbag light on these trucks.
Free under recall 24V-199. Check the VIN first.
Transmission control unit can leak fluid and cut drive
- What you'll notice
- A sudden loss of drive, no response when you select a gear, or the truck will not hold Park.
- Why it happens
- A weld in the transmission control unit can leak fluid and upset the valve body.
- What to do
- Have it repaired under recall 24V-413 right away, and always set the parking brake until it is fixed.
Free under recall 24V-413. Check the VIN first.
Missing clip at the brake master cylinder (do-not-drive recall)
- What you'll notice
- The brake pedal can suddenly go to the floor with little or no braking.
- Why it happens
- A retaining clip may have been left off the master cylinder push rod, so the pedal can come away from the master cylinder.
- What to do
- Do not drive the truck. Check the VIN for recall 21V-037 and have it towed to a dealer for the free fix.
Do not drive. Free under recall 21V-037, including the tow in most cases. Check the VIN first.
Steering control module fault can affect driver airbag deployment
- What you'll notice
- Usually nothing is noticed, though the airbag light may come on.
- Why it happens
- A fault in the steering control module can keep the driver airbag from deploying the way it should.
- What to do
- Check the VIN for recall 25V-765 and have the module replaced.
Free under recall 25V-765. Check the VIN first.
Intake plenum gasket leak (Magnum V8/V6)
- What you'll notice
- The engine burns oil, puffs blue smoke, pings under load, idles rough or misfires (often on one cylinder) and fouls spark plugs.
- Why it happens
- The intake manifold has a steel bottom plate sealed by a gasket that wears out. Once it leaks, the engine pulls oil and unmetered air into the cylinders.
- What to do
- Have the plenum gasket checked and repaired with an updated plate or kit before oily exhaust clogs the catalytic converter or the engine overheats.
Camshaft position sensor failure (Magnum)
- What you'll notice
- Hard starting or no-start, stalling while driving, rough idle, and a check engine light.
- Why it happens
- The cam sensor fails or gets fouled, so the computer loses track of engine timing.
- What to do
- Have the codes read. A failed cam sensor is an inexpensive part, but stalling in traffic is a hazard, so do not put it off.
Ticking from broken exhaust manifold bolts
- What you'll notice
- A tapping or ticking noise, loudest on a cold start, that can sound like a lifter. You may also smell exhaust under the hood.
- Why it happens
- Bolts holding the exhaust manifold to the cylinder head snap with repeated heating and cooling, and the joint leaks.
- What to do
- Have the broken bolts and gasket replaced before the leak burns the gasket area, upsets oxygen sensor readings or lets fumes reach the cab.
Worn front ball joints and tie rods
- What you'll notice
- Clunking over bumps, wandering on the highway, uneven front tire wear, or a loose steering feel.
- Why it happens
- The front ball joints and tie rod ends on this generation wear out early, especially on heavier 4x4 trucks.
- What to do
- Have the front end inspected. A badly worn ball joint can separate, so replace worn parts promptly and get an alignment afterward.
Tailgate strikers out of alignment (recall)
- What you'll notice
- The tailgate may not latch firmly and can open while driving.
- Why it happens
- The tailgate strikers can be set in the wrong position, so the latches do not grip fully.
- What to do
- Check your VIN for the recall and have the strikers adjusted.
Misfires and stalling on the Hurricane HO engine
- What you'll notice
- Check engine light with misfire codes on several cylinders, rough running, or stalling.
- Why it happens
- A bulletin found a purge line that can come disconnected, causing misfire codes. Owners have also reported other driveability faults.
- What to do
- Have the dealer check for the bulletin and stored codes. Get it looked at soon if it stalls.
Stability control can switch off from an ABS software fault
- What you'll notice
- The ABS and stability control lights come on and those systems stop helping.
- Why it happens
- Software in the anti-lock brake module can shut electronic stability control down.
- What to do
- Have the software updated under recall 24V-653. Normal braking still works, but leave extra room in rain and snow.
Free under recall 24V-653. Check the VIN first.
Instrument cluster can go blank from a software fault
- What you'll notice
- The digital cluster goes dark or shows nothing at startup, leaving no speed reading or warning lights.
- Why it happens
- A software error can stop the cluster from displaying.
- What to do
- Have the software updated under recalls 25V-826 or 26V-225. Driving with no warning lights hides other faults.
Free under recalls 25V-826 and 26V-225. Check the VIN first.
Damaged wheel hub sensor ring can disable stability control
- What you'll notice
- ABS and stability control warning lights, and the systems stop working.
- Why it happens
- The encoder ring in the front wheel hub can be damaged, so the module gets no usable wheel speed signal.
- What to do
- Have the hub assembly replaced under recall 24V-794. Braking still works, but there is no electronic help in a slide.
Free under recall 24V-794. Check the VIN first.
Headlight wiring can make the parking and daytime lights flicker
- What you'll notice
- Parking lights or daytime running lights flicker, dim or go out altogether.
- Why it happens
- Wiring inside the headlight assemblies can lose a solid connection.
- What to do
- Have the headlight assemblies replaced under recall 26V-421 so other drivers can see the truck at dusk.
Free under recall 26V-421. Check the VIN first.
Heated tow mirror glass can come off
- What you'll notice
- The driver side mirror glass loosens, flaps or falls out of the housing.
- Why it happens
- The bond holding the heated glass to the mirror backing can let go.
- What to do
- Have the glass replaced under recall 24V-754 and avoid towing or lane changes with a missing mirror.
Free under recall 24V-754. Check the VIN first.
Power module (TIPM) faults cause no-start and stalling
- What you'll notice
- The truck cranks but will not fire, or the fuel pump keeps buzzing after the key is off, the horn sounds on its own, lights and wipers act up, and some owners have the engine quit while driving.
- Why it happens
- Relays built into the totally integrated power module, the fuse and relay box under the hood, fail inside the sealed unit. The fuel pump relay is the usual one to go.
- What to do
- Have the module tested instead of replacing one part at a time, and get it done soon. A fuel pump relay that drops out can stall the truck in traffic.
Cracked dashboard
- What you'll notice
- Cracks open up across the top of the dash and spread until chunks of plastic break loose.
- Why it happens
- The dash plastic on these trucks turns brittle after years of sun and heat cycles.
- What to do
- Cosmetic in most cases. A molded dash cap or replacement top panel is the usual repair; remove loose sharp pieces near the airbag area.
Blend door problems cause weak or one-temperature airflow
- What you'll notice
- Heat or A/C stays stuck at one temperature, comes from the wrong vents, or is weak; you may hear clicking behind the dash.
- Why it happens
- The blend or recirculation doors behind the dash, or the small motors that move them, stop working properly.
- What to do
- Have the HVAC doors and actuators checked. It is not a safety issue unless the defroster cannot clear the windshield.
Water leak at the third brake light
- What you'll notice
- Water stains on the rear headliner or water at the back of the cab after rain or a car wash.
- Why it happens
- Rain gets past the seal of the high-mounted third brake light on the roof.
- What to do
- Have the dealer check the bulletin; the fix is a new third brake light assembly. Repair it before water causes mold or electrical faults.
Turn signal may not cancel on its own
- What you'll notice
- The blinker keeps clicking after you have finished the turn and has to be switched off by hand.
- Why it happens
- The steering column module that cancels the signal can malfunction.
- What to do
- Have the module checked under recall 24V-729, and watch your indicator so you are not signaling a turn you are not making.
Free under recall 24V-729. Check the VIN first.
Tire pressure sensors may miss low pressure
- What you'll notice
- The low tire warning does not come on even when a tire is clearly soft.
- Why it happens
- Faulty pressure sensors may not report or may not trigger the warning light.
- What to do
- Have the sensors replaced under recall 26V-623, and check the tires with a gauge every few weeks in the meantime.
Free under recall 26V-623. Check the VIN first.
Repair prices for your Ram 1500
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Repair intake plenum with updated plate or gasket kit
- Replace transmission with a remanufactured 46RE/47RE unit
- Replace camshaft position sensor (in the distributor)
- Extract broken manifold bolts and replace gasket
- Replace front upper and lower ball joints and tie rod ends
- Replace HVAC blend door actuator
- Replace both head gaskets and have the heads checked
- Replace camshaft and lifters
- Update software and replace shift interlock if needed
- Repair tailgate latch per recall
- Replace EGR cooler and inspect intake manifold
- Replace high-pressure fuel pump
- Engine computer software update per recall
- Replace side curtain airbags per recall
- Secure battery ground fastener; replace steering gear if needed
- Adjust or replace tailgate strikers per recall
- Replace totally integrated power module and program it to the truck
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Inspect and reattach second row seat belt anchorsNo charge if your vehicle is included
- Update anti-lock brake module softwareNo charge if your vehicle is included
- Replace steering column control moduleNo charge if your vehicle is included
- Inspect and replace steering column moduleNo charge if your vehicle is included
- Replace transmission valve body and control unitNo charge if your vehicle is included
- Update software or replace instrument clusterNo charge if your vehicle is included
- Replace front wheel hub and bearing assemblyNo charge if your vehicle is included
- Replace headlight assembliesNo charge if your vehicle is included
- Install brake master cylinder push rod clipNo charge if your vehicle is included
- Replace heated tow mirror glassNo charge if your vehicle is included
- Replace steering control moduleNo charge if your vehicle is included
- Replace tire pressure sensorsNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.