Subaru Foresterproblems, repair costs and recalls
Problems reported across 1998–2026. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
31 documented issues across all years, most serious first.
Head gasket leaks
- What you'll notice
- Coolant that keeps going down, a sweet smell after driving, the temperature gauge climbing, or oil and coolant seeping where the cylinder heads meet the engine block.
- Why it happens
- The non-turbo 2.5L boxer engine of this era is known for head gasket failure as it ages. Earlier engines tended to leak internally and overheat, while later ones more often seeped oil or coolant on the outside first.
- What to do
- Have a cooling system pressure test and inspection at the first sign of seepage or coolant loss. If the engine overheats, pull over and shut it off, because driving hot can warp the heads.
Front control arm brackets can rust and break
- What you'll notice
- Clunking from the front end, loose or wandering steering, or nothing at all until a bracket gives way.
- Why it happens
- In salt-belt states the brackets that hold the front lower control arms can corrode badly. Subaru recalled affected vehicles to inspect, rustproof or replace the arms.
- What to do
- Check your VIN for an open recall. If the front end clunks or the steering feels loose, have it inspected before driving further.
Turbocharger failure from oil starvation
- What you'll notice
- Blue smoke from the exhaust, a siren-like whine or loss of boost, and sometimes check engine codes for cam timing (P0011 or P0021).
- Why it happens
- A small filter screen in the banjo bolt that feeds oil to the turbo can clog with sludge, starving the turbo of oil. Skipped or late oil changes make it much more likely.
- What to do
- Stop driving hard and have it checked right away if you see smoke or lose boost. A shop can inspect or replace the oil feed screen, and regular oil changes with the correct oil are the best prevention.
Brake lines can rust through
- What you'll notice
- A soft or sinking brake pedal, brake fluid on the ground near the rear of the car, a brake warning light, or longer stopping distances.
- Why it happens
- In road-salt states, salty water could splash onto a brake line joint through a gap in the fuel tank protector and corrode it. Subaru recalled cars in salt-belt states, then recalled them again because the first fix was not done thoroughly enough.
- What to do
- Check your VIN for open recalls. If the pedal feels soft or you see fluid, do not drive until the brakes are inspected.
Rear center seat belt may not hold a child seat
- What you'll notice
- The rear middle seat belt will not lock when pulled all the way out, so a child seat installed with it can stay loose.
- Why it happens
- The automatic locking retractor on the rear center belt might not engage. Subaru recalled affected vehicles.
- What to do
- Use the outboard rear seats or the LATCH anchors for child seats until the recall is done, and check your VIN for an open recall.
Brake light switch can fail
- What you'll notice
- Brake lights stop working, and on push-button-start cars the engine may not start or the shifter may not come out of Park.
- Why it happens
- Contamination could build up inside the brake light switch and stop it from making contact. Subaru recalled affected vehicles.
- What to do
- Have someone check your brake lights and look up your VIN for an open recall. Drive carefully until fixed, as drivers behind you may get no warning when you brake.
Turbo intake duct can crack and stall the engine
- What you'll notice
- The engine runs rough, loses power, or stalls, often with a check engine light.
- Why it happens
- A rubber intake duct on the turbo engine could crack, letting unmeasured air in. Subaru recalled affected 2.0XT models.
- What to do
- Check your VIN for an open recall and have the duct replaced promptly.
Passenger airbag may switch off with an adult seated
- What you'll notice
- The passenger airbag OFF light stays on even when an adult is in the front seat.
- Why it happens
- On models with heated seats, a connection in the passenger seat occupant sensor could loosen. Subaru recalled affected vehicles.
- What to do
- Seat adults in the back if the OFF light comes on, and check your VIN for an open recall.
Fuel pump may fail
- What you'll notice
- Check engine light, rough running, stalling while driving, or an engine that will not restart.
- Why it happens
- An impeller inside the low-pressure fuel pump could deform and stop the pump. Subaru recalled affected 2018 Foresters.
- What to do
- Check your VIN for an open recall and get the pump replaced. If the engine stumbles or stalls, do not keep driving it.
PCV valve can break apart inside the engine
- What you'll notice
- Sudden loss of power, rough running, or new engine noise.
- Why it happens
- The aluminum PCV valve could separate and let pieces fall into the engine. Subaru recalled affected vehicles to replace the valve, or the short block if the pieces could not be recovered.
- What to do
- Check your VIN for an open recall and have the work done promptly. Stop driving if the engine suddenly loses power or knocks.
Electric power steering assist can cut out
- What you'll notice
- Steering suddenly becomes very heavy, usually with a steering warning light.
- Why it happens
- A connector inside the electric power steering unit could short and switch off the assist. Subaru recalled affected vehicles.
- What to do
- Check your VIN for an open recall. If steering goes heavy, slow down and steer firmly, then have it repaired before driving again.
Thermo control valve failure
- What you'll notice
- Check engine light, the engine running too hot or too cold, and EyeSight and other driver-assist features shutting off with warning lights.
- Why it happens
- The electronically controlled valve that manages coolant flow can fail, and Subaru issued a design-change bulletin for it. Owners have filed a class action alleging the valve can lead to overheating.
- What to do
- Have the codes read promptly and ask a Subaru dealer about the updated valve. If the temperature gauge climbs, stop and shut the engine off.
Some 18-inch wheels may not seat properly
- What you'll notice
- Vibration, a clicking or knocking from a wheel, or lug nuts that keep loosening.
- Why it happens
- Some 18-inch alloy wheels were made with the wrong lug seat shape, so they may not clamp tightly to the hub. Subaru recalled affected vehicles.
- What to do
- Check your VIN for an open recall and have the wheels inspected. If a wheel vibrates or knocks, stop driving and have it checked.
Moonroof glass may detach
- What you'll notice
- Wind noise or a rattle from the roof, or a glass panel that looks loose or lifted.
- Why it happens
- The moonroof glass panel may not have been bonded properly at the factory and could come off while driving. Subaru recalled affected Forester and Forester Hybrid models.
- What to do
- Check your VIN for an open recall and keep the moonroof closed until it is inspected.
Brake pedal can sink in extreme cold (recall)
- What you'll notice
- On a very cold morning the brake pedal travels much further than normal, possibly to the floor, and the car takes longer to stop.
- Why it happens
- In severe cold the brake master cylinder on ABS-equipped cars could lose its seal and let the pedal drop. Subaru recalled these cars to replace the master cylinder.
- What to do
- Check the VIN for recall 99V-040. If the pedal ever sinks toward the floor, do not drive the car; have it towed to a shop.
Automatic may not hold in Park (recall)
- What you'll notice
- The car creeps or rolls after the shifter is placed in Park, especially on a slope.
- Why it happens
- A parking rod inside the automatic transmission was not made correctly on some cars, so the park lock may not engage. Subaru recalled them to replace the parking rod.
- What to do
- Check the VIN for recall 02V-282 and have it done. Until then always set the parking brake firmly before getting out.
Air injection pump relay can stick on and overheat (recall)
- What you'll notice
- A whirring pump noise that carries on after start-up or with the engine off, a burning smell from the engine bay, or a dead battery.
- Why it happens
- The relay for the secondary air injection pump can fail in the on position. The pump then runs non-stop, overheats and can start a fire. Subaru recalled affected cars to replace the relay.
- What to do
- Check the VIN for recall 16V-738 and have the relay replaced. If you smell burning or hear a pump running with the engine off, stop using the car and have it inspected.
Front driveshaft joint can crack and break (recall)
- What you'll notice
- Clicking or clunking from the front when pulling away or turning, a sudden loss of drive, or the car rolling even though it is in Park.
- Why it happens
- The outer housing of a front driveshaft joint may have been made incorrectly and can crack and come apart. Subaru recalled affected cars to replace the front driveshafts.
- What to do
- Check the VIN for recall 23V-754 and have it done promptly. Use the parking brake every time you park, and stop driving if you hear clunking from the front axle.
Front ball joint nut may be loose (do-not-drive recall)
- What you'll notice
- A clunk or looseness from the left front wheel, wandering steering, or in the worst case the wheel folding outward.
- Why it happens
- The nut that secures the left front lower ball joint may not have been fastened correctly. If the joint separates, steering control can be lost. Subaru told owners of affected cars not to drive them.
- What to do
- Check the VIN for recall 26V-685 right away. If your car is included, do not drive it; ask the dealer to arrange towing and the repair.
AWD binding in tight turns (automatic)
- What you'll notice
- In slow, tight turns such as parking lots the car feels like it is braking itself, hops, or shudders, and it may get worse as the transmission warms up.
- Why it happens
- On automatic models the center clutch pack that splits power front to rear can stay locked up, often from a weak duty C solenoid, worn clutch plates, or mismatched tire sizes.
- What to do
- Make sure all four tires match in brand, size and wear, then have a Subaru-savvy shop check the transmission fluid and the AWD solenoid. Ongoing binding wears the drivetrain, so do not ignore it.
Catalytic converter failure (P0420)
- What you'll notice
- Check engine light with code P0420, a failed emissions test, or sometimes a rattle from under the car.
- Why it happens
- Owners of this generation frequently report worn-out catalytic converters, sometimes made worse by misfires or an engine burning oil or coolant.
- What to do
- Have the code confirmed and the oxygen sensors and engine checked for misfires or head gasket problems first, so a new converter is not ruined.
Wheel bearing hum
- What you'll notice
- A humming or growling noise that rises with speed and may change when you steer left or right.
- Why it happens
- Owners of this generation commonly report worn wheel bearings, especially in the rear.
- What to do
- Have the bearings checked soon. A badly worn bearing can overheat and affect wheel stability.
Excessive oil consumption
- What you'll notice
- The oil level drops noticeably between changes and the low oil pressure light may flicker in turns or come on.
- Why it happens
- Early FB25 engines could burn oil past the piston rings. A class settlement covered testing and repairs on many of these vehicles for an extended period.
- What to do
- Check the oil every few fill-ups and keep it topped up. Ask a Subaru dealer for an oil consumption test and whether your VIN qualifies for repair coverage. Never let it run low.
CVT shudder, jerking or stalling
- What you'll notice
- A shudder or jerk as the car pulls away or at light throttle, sometimes a hesitation before it moves, and in bad cases a stall.
- Why it happens
- Torque converter, valve body and seal problems in the Lineartronic CVT caused these complaints. Subaru extended CVT warranty coverage on 2014-2015 Foresters.
- What to do
- Ask a Subaru dealer about software updates, fluid leak bulletins and whether your VIN is still within the extended CVT coverage. Keep the CVT fluid serviced.
Battery drains while parked
- What you'll notice
- The car will not start after sitting, sometimes only overnight, and new batteries die early too.
- Why it happens
- Owners alleged that some modules stay awake after shutdown and keep drawing power. Subaru denied a defect but settled a class action that extended battery coverage on these years.
- What to do
- Have the battery and parasitic draw tested, ask the dealer about software updates, and check whether the settlement coverage applies to your car.
Rear stabilizer bar bracket bolts can loosen
- What you'll notice
- Clunking from the rear over bumps or a change in how the car leans in corners.
- Why it happens
- Bolts holding the rear stabilizer bar brackets could back out. Subaru recalled affected vehicles.
- What to do
- Check your VIN for an open recall and have the bolts inspected and replaced.
Windshield cracks with no clear impact
- What you'll notice
- A crack appears in the windshield, often starting at an edge, without a rock strike; some owners report repeat cracks after replacement.
- Why it happens
- Many owners report spontaneous windshield cracking on this generation. Subaru denied a defect but settled a class action offering an updated windshield and extended coverage.
- What to do
- Get a crack that blocks your view or reaches the camera area fixed quickly, and ask the dealer about the updated windshield and settlement coverage. EyeSight must be recalibrated after replacement.
Reverse lights and backup camera may not work (recall)
- What you'll notice
- The backup camera stays blank and the reverse lights do not come on when Reverse is selected. A warning light may appear.
- Why it happens
- A weld on the transmission's inhibitor switch can let water in, so the car no longer knows it is in Reverse. Subaru recalled affected cars to replace the switch.
- What to do
- Check the VIN for recall 23V-755 and book the repair. Until it is done, back up with extra care and do not rely on the camera.
Child seat anchor bolts may be loose (recall)
- What you'll notice
- Usually nothing you can see or feel. A child seat attached to the rear anchors may not be held as firmly as it should be in a crash.
- Why it happens
- The bolts for the rear child seat anchors may not have been tightened properly at the factory. Subaru recalled affected cars to tighten them.
- What to do
- Check the VIN for recall 25V-419 and have a dealer tighten the bolts before relying on those anchors for a child seat.
Rear hatch support bracket can detach (recall)
- What you'll notice
- The open rear hatch sags, will not stay up, or drops without warning.
- Why it happens
- A bracket for the hatch support strut may be the wrong part or fitted the wrong way round and can come off. Subaru recalled affected cars to replace the strut and bracket as needed.
- What to do
- Check the VIN for recall 25V-889. Until it is repaired, keep your head and hands clear of the open hatch and do not let children stand under it.
Rattling exhaust heat shields
- What you'll notice
- A tinny buzz or rattle from under the car at certain engine speeds, often at idle or light acceleration.
- Why it happens
- The thin heat shields around the exhaust rust at their mounting points and come loose.
- What to do
- Have a shop secure the shield with a clamp or replace it. This is usually a quick, simple repair.
Repair prices for your Subaru Forester
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace both head gaskets and resurface heads
- Replace AWD transfer (duty C) solenoid
- Replace front lower control arms per recall
- Replace front catalytic converter (Y-pipe)
- Replace front wheel bearing
- Replace turbocharger and oil feed line
- Replace rusted brake lines per recall
- Replace rear center seat belt assembly per recall
- Replace short block (piston rings)
- Replace CVT valve body and refill fluid
- Replace brake light switch per recall
- Replace turbo air intake duct per recall
- Repair passenger seat sensor mat harness per recall
- Test for parasitic drain and replace battery
- Replace in-tank low-pressure fuel pump per recall
- Replace PCV valve per recall
- Inspect and replace steering gearbox per recall
- Retorque or replace stabilizer bracket bolts per recall
- Replace thermo control valve and refill coolant
- Replace windshield and recalibrate EyeSight camera
- Inspect and replace affected wheels per recall
- Check bond and replace moonroof glass panel per recall
- Replace brake master cylinder and bleed brakes
- Replace transmission parking rod assembly
- Replace secondary air pump relay
- Replace transmission inhibitor switch
- Replace both front driveshafts (CV axles)
- Tighten child seat anchor bolts
- Inspect and replace left front lower ball joint
- Replace rear hatch support strut and bracket
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.