Toyota 4Runnerproblems, repair costs and recalls
Problems reported across 1996–2027. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
28 documented issues across all years, most serious first.
2WD stability under heavy load (recall 02V021)
- What you'll notice
- With a heavy load on board, the truck can feel unstable or tippy during sharp or sudden steering.
- Why it happens
- On two-wheel-drive trucks, a combination of heavy loading and hard steering could make the vehicle lose stability. Toyota recalled these trucks for a free fix.
- What to do
- Check the VIN for an open recall and have it done before carrying heavy loads. Avoid overloading and sudden swerves until it is fixed.
Free at a Toyota dealer under the recall. Check your VIN first.
Front lower ball joint wear (recall 05V225)
- What you'll notice
- Clunking from the front over bumps, loose or wandering steering, or uneven front tire wear.
- Why it happens
- The front lower ball joints can wear faster than they should. A badly worn joint can pull apart from the steering knuckle, letting the wheel fold under the truck. Toyota recalled these years to replace them.
- What to do
- Check the VIN for the recall and have the ball joints inspected right away. Do not keep driving with a clunking front end.
Free at a Toyota dealer under the recall. Check your VIN first.
Frame rust in salt-belt states
- What you'll notice
- Flaking or bubbling rust on the frame rails and crossmembers, holes in the frame, or new creaks and clunks from underneath.
- Why it happens
- The frame's protective coating breaks down under road salt, and on many trucks the rust eventually eats through structural parts of the frame.
- What to do
- Have the frame inspected on a lift, especially before buying one of these trucks. A frame with holes is a safety risk and should be repaired or replaced before regular driving.
Fuel pulsation damper leak (recall 03V146)
- What you'll notice
- Raw fuel smell from the engine bay or wetness around the fuel rail.
- Why it happens
- The fuel pulsation damper on some early 2003 trucks may not have been put together correctly and can leak fuel near hot engine parts.
- What to do
- Any fuel smell means stop and get it checked. Confirm by VIN that the recall was done.
Free at a Toyota dealer under the recall. Check your VIN first.
Floor mat can trap the gas pedal (recall 11V113)
- What you'll notice
- The gas pedal sticks down or returns slowly, and the truck keeps accelerating.
- Why it happens
- An unsecured or wrong floor mat can slide forward and hold the accelerator pedal down. Toyota added these trucks to its floor mat recall.
- What to do
- Use only a secured mat made for this truck and never stack mats. Check the VIN for the recall. If the pedal sticks, shift to neutral and brake firmly.
Free at a Toyota dealer under the recall. Check your VIN first.
Side curtain airbags may fire without a crash (recall 16V065)
- What you'll notice
- Usually no warning. The side curtain airbags may go off while driving with no collision.
- Why it happens
- A problem in the curtain airbag system could make the bags deploy when they are not needed, which can startle or injure people inside.
- What to do
- Ask a Toyota dealer to confirm the recall applies to the VIN and get the free recall repair done soon.
Free at a Toyota dealer under the recall. Check your VIN first.
Fuel pump may fail and stall the engine (recall 20V012)
- What you'll notice
- Rough running, check engine light, failure to start, or the engine stalling while driving.
- Why it happens
- The low-pressure fuel pump in the tank can fail, cutting fuel to the engine.
- What to do
- Check the VIN for the recall and get the free pump replacement. A stall at speed is dangerous, so do not put it off.
Fuel pump may fail and stall the engine (recall 20V682)
- What you'll notice
- Rough running, check engine light, failure to start, or the engine stalling while driving.
- Why it happens
- The same low-pressure fuel pump problem found on earlier years was later recalled on these trucks too.
- What to do
- Check the VIN for the recall and get the free pump replacement. A stall at speed is dangerous, so do not put it off.
Loose steering or suspension bolts (recall 19V670)
- What you'll notice
- Clunks or knocks from the front, a loose steering feel, or the truck pulling to one side.
- Why it happens
- Some steering and suspension fasteners may not have been tightened enough at the factory and can work loose.
- What to do
- Check the VIN for the recall and have the bolts inspected and tightened soon. Stop driving if steering feels loose.
Gauge cluster may not show speed or warnings (recall 25V595)
- What you'll notice
- After starting, the instrument panel may not display the speedometer, brake warning or tire pressure warning.
- Why it happens
- A software problem in the instrument cluster can keep key information and warnings from showing.
- What to do
- Check the VIN for the recall and get the free software fix. Do not drive without a working speedometer and warnings.
Head gasket failure on the early 4.0L V6
- What you'll notice
- A rough, shaky idle for the first minute after a cold start, a flashing or steady check engine light with a misfire on one cylinder, a sweet coolant smell from the exhaust, and a coolant level that keeps dropping with no puddle under the truck.
- Why it happens
- On early versions of the 4.0L V6 a head gasket can start to seep, usually at one of the rear cylinders, letting coolant into the cylinder while the engine sits. Owners most often report it well past the hundred-thousand-mile mark.
- What to do
- Do not keep driving with a cold-start misfire and falling coolant. Overheating or coolant in a cylinder can ruin the engine. Have a shop pressure-test the cooling system and check the cylinders before deciding on a repair.
Add-on seat heaters can short and burn the seat
- What you'll notice
- A hot spot, a burning smell, or scorch marks in the seat cushion, or a heated seat that quits working.
- Why it happens
- Accessory seat heaters fitted at the dealer used copper-strand wiring that can break where the cushion flexes and short out.
- What to do
- Stop using the seat heater and check the VIN. The recall remedy disconnects the heater and refunds what was paid for it.
Add-on remote starter can knock out ABS and stability control
- What you'll notice
- ABS, traction and stability control warning lights come on, and those systems stop working.
- Why it happens
- A non-original remote engine starter can interfere with the vehicle's data network and cut communication with the brake systems.
- What to do
- Have the starter replaced under recall 12V-120. Until then expect no ABS help in a panic stop, so leave extra space.
Radiator can let coolant into the transmission fluid
- What you'll notice
- Slipping or jerky shifts, then no drive at all, with transmission fluid that looks pink and milky instead of red, and coolant that disappears from the tank.
- Why it happens
- The automatic transmission cooler is built into the radiator on these years. When the barrier between the two sides corrodes, coolant and transmission fluid mix and the mixture destroys the transmission clutches.
- What to do
- Stop driving and have the fluid checked the moment shifting turns odd or coolant goes missing. A new radiator is far cheaper than a transmission, but once the fluid has mixed the transmission usually needs work too.
Secondary air injection pump or valve failure
- What you'll notice
- Check engine light, and sometimes the truck runs in a reduced-power mode right after a cold start.
- Why it happens
- The air pump and its switching valve that help clean exhaust on cold starts can fail, often after moisture gets inside. Toyota covered the fix in a bulletin.
- What to do
- Have the codes read and the pump and valve tested. Ask a dealer whether the bulletin applies to your truck.
Hydraulic suspension leaks (KDSS or X-REAS)
- What you'll notice
- Oily fluid near the front sway bar or shocks, a suspension warning, a harsher ride, or the truck leaning to one side.
- Why it happens
- Trucks with KDSS or the X-REAS shock system use hydraulic lines and cylinders that can corrode or wear and start leaking with age.
- What to do
- Have the system inspected and the leak fixed. Rinse the underside after driving on salted roads to slow corrosion.
Grille or hood overlay can come loose (recall 17V763)
- What you'll notice
- A rattle from the front of the truck or a trim piece on the hood or grille that feels loose.
- Why it happens
- A fastener holding the decorative overlay can break, letting the piece come off while driving.
- What to do
- Check the VIN for the recall and have the fasteners replaced. Do not drive at highway speed with loose front trim.
Rough or clunky shifts from the 8-speed automatic
- What you'll notice
- Jerky or delayed shifts, a clunk when the transmission engages, or unexpected downshifts, mostly at low speed or under load.
- Why it happens
- Owners of the new generation report shift quality problems with the 8-speed automatic shared with the Tacoma. No single cause has been confirmed, and a few transmissions have been replaced under warranty.
- What to do
- Report it to a Toyota dealer while under warranty and ask about software updates. Have it checked sooner if it slips or shows warning lights.
Front brake calipers stick and drag
- What you'll notice
- The truck pulls to one side, a wheel gets very hot and smells after a drive, fuel economy drops, or the brake pedal feels like it stays slightly applied.
- Why it happens
- The front caliper slides and piston seize up, usually from corrosion in areas with road salt, so the pads stay pressed against the rotor.
- What to do
- Have the front brakes inspected. A dragging caliper cooks the pads and rotor and can overheat the wheel bearing, so do not put it off.
Accessory exhaust tip can burn people behind the truck
- What you'll notice
- The chrome tip sits close to the bumper edge and stays very hot after driving.
- Why it happens
- A dealer-installed exhaust tip was fitted too far out, so someone loading the back can touch it.
- What to do
- Check the VIN for this recall. The fix is a smaller tip that sits recessed, and it is free.
Passenger airbag sensor may be out of calibration
- What you'll notice
- The passenger airbag off light behaves oddly, staying on with an adult in the seat or off with the seat empty.
- Why it happens
- The seat's occupant weight sensing could be left out of calibration after accessories were installed at the dealer, so the airbag may not react correctly.
- What to do
- Have a Toyota dealer test and recalibrate the system under recall 13V-014 before carrying a front passenger regularly.
High beam can stop working after fog lights are fitted
- What you'll notice
- The driver's side high beam does not come on when you flick the stalk.
- Why it happens
- Installing the accessory fog light kit can overload part of the headlight wiring.
- What to do
- Have the updated harness fitted under recall 21V-963, and avoid dark back roads until the high beams work.
Cracked dashboard
- What you'll notice
- Long cracks across the top of the dash, sometimes near the passenger airbag area.
- Why it happens
- The soft dash pad breaks down from heat and sun over the years. Toyota issued a bulletin and extended coverage at the time, but that coverage is long over.
- What to do
- Not a driving hazard on its own. A dash cover or a replacement dash pad fixes the look.
Harsh low-speed shifts
- What you'll notice
- Firm or jerky shifts at low speed, especially when slowing down and pulling away again.
- Why it happens
- Early fifth-generation trucks had transmission shift complaints that Toyota addressed with a dealer update.
- What to do
- Ask a dealer whether a software update or bulletin applies. If shifts get worse or the truck slips, have it checked sooner.
Door lock actuator failures
- What you'll notice
- One or more doors will not lock or unlock with the key fob or switch, or the doors do not auto-lock.
- Why it happens
- The small motors inside the door latches wear out and stop working on many trucks of this era.
- What to do
- Have the failed actuator replaced. Lock that door by hand in the meantime.
Infotainment screen freezes or reboots
- What you'll notice
- The touchscreen locks up, restarts on its own, or is very slow to respond.
- Why it happens
- The head unit software of this period is prone to glitches. Firmware updates fix many cases, and some units need replacing.
- What to do
- Ask a dealer for any available software update. Replace the unit only if updates do not help.
Accessory hood scoop can come loose
- What you'll notice
- The add-on hood scoop lifts at the edges, rattles at speed, or peels away from the hood.
- Why it happens
- The scoop was held on with adhesive that can weaken with heat and washing.
- What to do
- Have the scoop mechanically fastened under recall 17V-425 so it cannot come off on the highway.
Load capacity label may show the wrong weight
- What you'll notice
- Nothing is wrong with the truck, but the sticker in the door jamb overstates how much weight you can add.
- Why it happens
- The label did not account for accessories fitted before delivery, so the stated carrying capacity is too high.
- What to do
- Get the corrected label free from a dealer and go by the new figure when loading people, gear or a trailer tongue.
Repair prices for your Toyota 4Runner
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Cut out rusted frame sections and weld in repair plates
- Replace secondary air pump and air switching valves
- Replace leaking KDSS accumulator or cylinder
- Replace one door lock actuator
- Replace fuel pump
- Secure or replace hood and grille trim
- Inspect and tighten steering and suspension bolts
- Update instrument cluster software
- Update transmission software and check fluid
- Replace head gaskets and resurface cylinder heads
- Replace front brake caliper, pads and rotor
- Disconnect accessory seat heater and inspect wiring
- Replace dealer-installed exhaust tip
- Test and recalibrate occupant sensing system
- Remove or replace non-original remote starter
- Mechanically fasten accessory hood scoop
- Install updated headlight wiring harness
- Install corrected load capacity label
- Replace radiator and flush transmission cooler lines
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Replace rear suspension partsNo charge if your vehicle is included
- Replace front lower ball jointsNo charge if your vehicle is included
- Replace fuel pulsation damperNo charge if your vehicle is included
- Modify or replace accelerator pedal and replace floor matNo charge if your vehicle is included
- Replace airbag control moduleNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.