Home › Warning lights › ABS warning light
Amber/yellow: check soon

ABS warning light

Also called: Anti-lock brake light

How urgent? Get it checked soon

What it means

The anti-lock brake system has a fault and is turned off. Your normal brakes still work, but the wheels can lock up in a hard stop.

An amber or yellow light in the instrument cluster, usually a circle with the letters ABS inside it and a curved bracket on each side. Some makes drop the circle and just show ABS in plain amber letters, and some trucks and European cars print a message such as ABS fault or Anti-lock brakes instead. It is normal for it to glow for a second or two when you first start the car and then go out.

Can I keep driving?

Yes, carefully. Leave extra stopping distance, especially on wet or icy roads, and get it checked soon. If the red brake light is on too, stop driving.

What to do now

  1. Drive gently and avoid hard stops.
  2. Check the brake fluid level.
  3. Have the ABS codes read; a wheel speed sensor is the usual cause.

Common causes

  • Faulty wheel speed sensor or damaged wiring
  • Damaged tone ring on a wheel hub
  • Low brake fluid
  • ABS control module or pump fault

Checks you can do yourself

Safe, no tools in most cases

Do these with the car parked and the engine off and cool. If anything looks or smells hot, wait.

1
Switch the car off and start it again

Turn the engine off, open and close the driver's door, wait about half a minute, then start it again and watch the light. Every car runs a quick self-test of the anti-lock brakes at start-up, and a one-off glitch, often from a weak battery or a brief wet connector, will not come back. If the light returns straight away, the car is finding a real fault.

2 minutes · None
2
Look at the brake fluid level

With the engine off and cool, open the hood and find the small see-through tank against the firewall on the driver's side. Read the level through the side of it without opening the cap; it belongs between the MIN and MAX marks. Low fluid can switch the anti-lock system off on its own, and it matters far more than the amber light does.

3 minutes · None
3
Check your tires are the right size and properly inflated

Read the size printed on the side of each tire and make sure all four match what the sticker in the driver's door frame calls for, with the front pair the same as each other and the rear pair the same as each other. Then set the pressures to that sticker with a gauge. The system works by comparing how fast each wheel turns, so one odd-sized or very soft tire can upset it.

15 minutes · Tire pressure gauge
4
Look at the sensor wire behind each front wheel

With the car parked and off, turn the steering fully to one side and look into the wheel well at the back of the brake disc. You should see a thin wire clipped along the suspension to a small sensor. Look only, and do not pull on it. A wire hanging loose, rubbed bare or chewed by an animal is the kind of thing that sets this light off, and it is worth pointing out to the shop.

10 minutes · None
5
Note what else lights up and when

Write down whether the traction control or stability light came on at the same time, whether the red brake light is on too, and whether the amber light appears the moment you start the car or only after a few minutes of driving. That pattern is the most useful thing you can hand a shop, and it costs nothing to collect.

5 minutes · None

Step-by-step repair walkthroughs for the fixes below are on the way.

What not to do

  • Don't assume the car stops as well as it used to on wet or icy roads. Without anti-lock brakes a hard stop can lock the wheels and you lose steering while they are locked.
  • Don't ignore it if the red brake light comes on as well. That combination is a brake problem, not just a switched-off safety feature, and the car should not be driven.
  • Don't pull the ABS fuse or cover the light to make it go away. You still have the fault, and now you have no warning of the next one.
  • Don't test it by slamming the brakes on a public road. Leave extra following distance instead and get the codes read.

What it usually turns out to be

Most likely first. Prices are typical US parts-and-labor totals for that repair, not a quote for your vehicle.

A failed wheel speed sensorPrice not verified

How you can tell This is the common one. The stored code names a single wheel, such as left front or right rear. Alongside the amber light, the speedometer may jump about, the anti-lock brakes may buzz and pulse at walking pace when you are only parking, and the traction control light often comes on too.

The repair The one sensor at that wheel is unbolted and replaced. On most cars it is a bolt-in part and a short job, though a few makes build it into the wheel bearing.

Damaged sensor wiring or a corroded connectorPrice not verified

How you can tell The light comes and goes rather than staying on, often appearing over bumps, in heavy rain, or only once the steering is turned. The code reads as an open or shorted circuit at one wheel. Looking in the wheel well you may see a chafed wire or a connector green with corrosion.

The repair The damaged length of wire or the connector plug is repaired or a new pigtail is spliced in, then the harness is clipped back where it cannot rub.

A damaged tone ring or a worn wheel bearingPrice not verified

How you can tell The tone ring is the toothed ring the sensor counts as the wheel spins. When its teeth rust away or get knocked about, the signal goes erratic rather than disappearing, so the light tends to come on above a certain speed. A humming or growling that changes as you steer left and right points at the bearing it sits in.

The repair The hub and bearing assembly, which usually carries both the ring and sometimes the sensor, is replaced as one unit.

Low brake fluid or another brake system faultPrice not verified

How you can tell The red brake warning light is on at the same time as the amber ABS light, and the fluid in the tank under the hood is at or below the MIN mark. The anti-lock system switches itself off when it cannot trust the brake pressure it has to work with, so the amber light here is a side effect.

The repair The real brake problem is fixed first, whether that is worn pads, a leaking line or a failing master cylinder, and then the fluid is topped and the system bled.

A failing ABS control module or pumpPrice not verified

How you can tell The codes point at the unit itself rather than at any one wheel, the light is on from the moment the car starts and never varies, and the traction and stability lights usually come on with it. Sometimes there is a buzz or clunk from the unit under the hood when you first drive off.

The repair The module, the computer and pump that work the anti-lock brakes, is rebuilt or replaced, and the new one has to be coded to the car. This is the expensive end of it.

A weak battery or poor chargingPrice not verified

How you can tell The ABS and traction lights flash up while the engine is cranking slowly, or after the car has sat for a few days, and clear once it has run for a while. Headlights may dim at idle. The anti-lock computer drops out when the voltage sags and reports a fault for it.

The repair The battery is tested and replaced if it is weak, or a charging fault at the alternator is sorted out, and the stored code is cleared.

What a shop will do

A shop plugs a scan tool into the anti-lock brake computer and reads the stored code, which usually names the wheel that went quiet. Then they watch all four wheel speeds live on a short drive and see which one drops to zero or jumps around while the car is clearly moving. From there they go to that wheel and check the sensor, its toothed ring and the wire running to it. They also check the fluid level and battery voltage first, since both can switch the system off on their own. That is normally half an hour to an hour.

How to reset this light

This is a fault light, not a reminder, so there is nothing you are meant to reset. A scan tool can clear the code and the light will go out, but the car tests the anti-lock system every single time you start it, and the light comes back on the next drive while the fault is still there. Once the sensor, the wire or the fluid is put right, most cars turn the light off by themselves after a short drive at normal road speed.

Some makes hold the light on after the repair until a scan tool clears the old code, so a shop visit may be needed even when the part has been fixed.

Walk through it step by step

Common questions

What does the abs warning light mean?

The anti-lock brake system has a fault and is turned off. Your normal brakes still work, but the wheels can lock up in a hard stop.

Can I drive with the abs warning light on?

Yes, carefully. Leave extra stopping distance, especially on wet or icy roads, and get it checked soon. If the red brake light is on too, stop driving.

Do my brakes still work with the ABS light on?

Yes. Your ordinary brakes are separate and still work normally, which is why this light is amber and not red. What you have lost is the anti-lock part, the bit that stops the wheels locking up in a panic stop. Leave more room, brake earlier and more gently, and get it looked at soon.

Will I fail inspection with the ABS light on?

In many states that run a safety or emissions inspection, an illuminated ABS light is a fail, and in states with an OBD scan the stored brake code can fail it too. Rules vary by state and some older vehicles are exempt, so check your own state's list, but expect to fix it first.

Is it safe to drive with the ABS light on in rain or snow?

It is riskier than usual, and that is the part people underestimate. With the anti-lock system off, a hard stop on a wet or icy road can lock the wheels, and locked wheels will not steer. Slow down, double your following distance, and brake in steady light pressure rather than one hard push.

The ABS light came on right after I had tires or wheels done. Why?

Wheel work is a very common trigger. A sensor wire can be knocked loose or pinched, a sensor can be left unplugged, or a mismatched or wrong-size tire can upset the wheel speed comparison. Go back to whoever did the work first and ask them to check their own job before paying for diagnosis.

Will the ABS light go off by itself?

Sometimes, if the cause was temporary, such as a weak battery or a wet connector that has dried out. If the fault is still there, it will not clear, and clearing the code without repairing anything just buys you one quiet drive. A light that goes off and comes back is still telling you something is wrong.

Sources: Jerry · YourMechanic · Kelley Blue Book

Not your light? These get mixed up with it

Symbols vary a little between makes. Your owner's manual shows the exact lights for your vehicle. This is a general guide, not a diagnosis.