Traction / stability control light
Also called: ESC light, Skidding car light, VSC light
What it means
The traction or stability control system is working, has been switched off, or has a fault. If it flashes while you drive it is doing its job on a slippery road; if it stays on, the system is off or has a fault.
It sits with the other warning lights in the instrument cluster, usually amber. Most makes draw a small car seen from behind with two wavy skid lines beneath it. Some use letters instead: VSC or TRAC OFF on Toyota, VSA on Honda, ESP or ESP BAS on Chrysler and Dodge, DSC on BMW, and a plain text message such as Service StabiliTrak on GM.
Can I keep driving?
Yes. If it flashes on slippery roads, ease off the gas. If it stays on, the car drives normally but has less help in a skid; get it checked.
If it's flashing or blinking: A quick flash while you are driving is normal. It means the system is cutting engine power or braking a spinning wheel right at that moment, usually on wet, icy or loose ground. A light that stays on steadily instead is telling you the system is off or has a fault.
What to do now
- Make sure the traction control button wasn't pressed off.
- If the ABS light is also on, the cause is often a wheel speed sensor.
- Have the codes read if it stays on.
Common causes
- System switched off
- Wheel speed sensor fault
- Steering angle sensor needs calibration
- Engine fault (check engine light on too)
Checks you can do yourself
Safe, no tools in most casesDo these with the car parked and the engine off and cool. If anything looks or smells hot, wait.
Look on the dash, the center console or near the gear lever for a button with the same skidding-car symbol, often marked TRAC OFF, ESC OFF or VSC OFF. If someone pressed it, press it once more and the light should go out. On many cars the system also switches itself back on when you shut the engine off and start it again.
2 minutes · NoneWalk around the cold, parked car and look at every tire. A soft tire, a tire much more worn than the others, or a spare of a different size makes the wheels turn at different speeds, and the system reads that as a fault. Check the pressures with a gauge against the sticker in the driver's door opening and set them to match.
10 minutes · Tire pressure gaugePark somewhere safe, switch the engine fully off, wait about half a minute, then start it again. Some of these faults are one-time glitches and the light clears on its own. If it comes straight back on, the car has stored a real fault and it needs the codes read.
5 minutes · NoneBefore you go to a shop, look across the cluster and note each warning light you can see. If the ABS light or the brake warning light is on with this one, the cause is usually a wheel speed sensor they share. If the check engine light is on too, an engine fault can shut traction control down as a side effect, and fixing the engine fixes both.
3 minutes · NoneStep-by-step repair walkthroughs for the fixes below are on the way.
What not to do
- Don't assume you still have the safety net. With this light on steady, the car will not catch a skid for you.
- Don't drive at your normal speed in rain, snow or on ice until it is fixed.
- Don't pull a fuse or disconnect the battery to kill the light. The fault stays and you lose other settings.
- Don't shrug it off if the ABS or brake light is on as well. That pair can mean your anti-lock brakes are off too.
What it usually turns out to be
Most likely first. Prices are typical US parts-and-labor totals for that repair, not a quote for your vehicle.
How you can tell The light is on steadily and the display may read TRAC OFF or ESC OFF rather than naming a fault. Press the button again, or shut the engine off and restart, and the light goes out. Nothing else on the dash is lit.
The repair Nothing to repair. Switch the system back on and leave it on.
How you can tell Usually the ABS light comes on at the same time, and cruise control stops working. A scan tool stores a code naming one wheel, such as left front. These sensors sit behind the wheels in road salt and grit, so this is the most common real fault by a wide margin.
The repair A shop replaces the single sensor the code points to, and sometimes the wire to it or the toothed ring it reads.
How you can tell Very common right after a wheel alignment, a steering repair, or front-end crash work. The power steering or ABS light often joins it, and the stored code names the steering angle sensor. The car does not know where straight ahead is.
The repair A shop recalibrates the sensor with a scan tool. If the sensor itself has failed it is replaced, usually inside the steering column, then calibrated.
How you can tell The check engine light is on as well. Traction control works by cutting engine power, so when the engine computer has a fault it hands in its notice and lights both. The skidding-car light is the symptom, not the problem.
The repair The shop repairs the underlying engine fault, often a throttle body, a misfire or a sensor, and the traction light goes out with it.
How you can tell Often your brake lights do not come on, or cruise control will not set. The system needs that little switch to know when your foot is on the brake, and without it the stability computer will not run.
The repair A new switch clips onto the brake pedal bracket and is adjusted.
How you can tell Both the ABS and traction lights stay on every trip, and a scan tool either stores an internal fault for the module or cannot talk to it at all. The brakes still stop the car, but the anti-lock and skid help are gone.
The repair The module is replaced, or taken off and rebuilt by a specialist, then programmed and calibrated to the car.
What a shop will do
They plug a scan tool into the port under the dash and read the stability control module, not just the engine, because a cheap code reader usually cannot see these codes. The stored code points at one wheel, the steering angle sensor or the module itself. Then they watch all four wheel speeds live to see which one drops out, and check that sensor and its wiring. Reading and confirming a clear code is typically under an hour; a fault that comes and goes takes longer.
How to reset this light
No. This is a fault light, not a service reminder. Clearing the code with a scan tool turns the light out for a moment, but it repairs nothing and the light returns as soon as the car sees the same fault again, often within a mile of driving. The one thing that looks like a reset is a light caused by someone pressing the off button, and switching the system back on is not a reset, it just turns the system back on.
After a genuine repair the light usually clears itself once the car has been driven a short distance, though some makes need the code cleared with a tool first.
Walk through it step by step
Trouble codes often stored with this light
Common questions
What does the traction / stability control light mean?
The traction or stability control system is working, has been switched off, or has a fault. If it flashes while you drive it is doing its job on a slippery road; if it stays on, the system is off or has a fault.
Can I drive with the traction / stability control light on?
Yes. If it flashes on slippery roads, ease off the gas. If it stays on, the car drives normally but has less help in a skid; get it checked.
Will my car pass inspection with the traction control light on?
In most states a traction control light on its own does not fail a safety inspection, but the rules differ state to state and some inspections do look at whether warning lamps are lit. If the ABS or brake light is on with it, you are far more likely to fail. It is not part of the emissions test, that one is the check engine light.
How long can I drive with the traction control light on?
The car still drives and brakes normally, so you can get home and to a shop. What you have lost is the computer's help if a wheel starts to slip. Treat it as a this-week repair, and in the meantime drive gently in rain, snow and ice.
Why does the light flash when I accelerate?
That is the system doing its job. It flashes while it is cutting power or braking a wheel that is spinning. Ease off the accelerator and it should stop. If it flashes on dry pavement with no slipping, something is wrong and it needs a scan.
Does the traction control light reset itself?
If the cause was a one-time glitch, often yes, and it goes out after you shut the engine off and start it again. If it comes back on every trip, the car has stored a real fault and the light will stay on until that fault is repaired.
Is it safe to drive in the rain or snow with this light on?
Driving is safe at sensible speeds, but you do not have the skid protection you normally have. Rain, snow and ice are exactly the conditions the system was built for, so slow down, leave much more space, and avoid hard acceleration out of corners and onto wet ramps.
Sources: YourMechanic · RepairPal