SLIP and VDC OFF indicators
Also called: SLIP light, VDC OFF light, Vehicle Dynamic Control light, Nissan traction control light
What it means
SLIP blinking as you drive means Nissan's Vehicle Dynamic Control is working to stop a wheel spinning. If SLIP stays on steady, usually alongside VDC OFF, the system has shut down, either because the VDC OFF button was pressed or because it found a fault.
Both are amber words rather than drawn symbols, in the message area near the speedometer. Nissan uses the single word SLIP, with VDC OFF below or beside it; some models add a small skidding-car outline, and Infiniti often uses that car symbol with OFF next to it. Seeing SLIP and VDC OFF lit together is normal for this fault, and the ABS light frequently joins them.
Can I keep driving?
Yes, carefully, in normal conditions. The car drives, steers and brakes as usual but nothing will catch a skid for you, so take extra care in rain, snow, gravel and on fast bends. If the ABS light or the check engine light is on with it, get it looked at soon rather than later.
If it's flashing or blinking: A blinking SLIP light while you are driving is normal and means the system is actively catching a slipping wheel, so ease off the accelerator: the road is slicker than it looks. Nissan's manual says it also blinks for wheel spin when VDC has been switched off. A SLIP light that stays on steady is the warning, not the flashing one.
What to do now
- Look for the VDC OFF button, usually low on the dash or near the shifter, and press it to switch the system back on, then restart the car.
- If the lights appeared right after a battery change, jump start or flat battery, drive straight above about 10 mph for at least ten minutes so the system can relearn.
- Check the tire pressures against the sticker in the driver's door opening, and that all four tires are the same size and not badly worn.
- If the lights stay on, or the check engine light is on too, have the ABS and VDC codes read; a wheel speed sensor is the usual culprit.
Common causes
- VDC switched off by the button, or 4WD in low range
- Wheel speed sensor or damaged sensor wiring
- Steering angle sensor needing a relearn after a battery disconnect
- Weak battery or low system voltage
- Mismatched, worn or wrong-size tires, or badly worn brake parts
- An engine fault with the check engine light, which shuts VDC down
Checks you can do yourself
Safe, no tools in most casesDo these with the car parked and the engine off and cool. If anything looks or smells hot, wait.
Hunt for a button marked VDC OFF, usually low on the dash to the left of the steering wheel or near the shifter. It is easy to catch with a knee or a bag. Press it once with the car parked and the engine running, then shut the car off and restart. If both lights go out and stay out, the system was simply switched off. On 4WD models, check you are not still in 4LO, which turns VDC off on purpose.
3 minutes · NoneIf the lights came on after a battery change, a jump start or a battery that went flat, the system has lost its straight-ahead reference. Nissan's own instruction is to drive straight on a quiet, level road at more than about 10 mph for at least ten minutes. If the lights go out during that drive, nothing is broken. If they are still on at the end, there is a real fault to find.
15 minutes · NoneSet all four tires to the pressure on the sticker in the driver's door opening, with the car cold. Then look at them: they should be the same size and brand, with similar tread depth. A space-saver spare or one odd tire makes that wheel turn at a different speed, which is enough to upset the system and light these warnings.
15 minutes · Tire pressure gaugeWith the engine off and cool, read the brake fluid level through the small see-through tank at the back of the engine bay: it should sit between the MIN and MAX marks. Nissan's manual notes that badly worn or non-standard brake pads, rotors or calipers can bring the VDC OFF light on. Peer through the wheel spokes at the pad: if the friction material looks paper thin, book a brake check.
5 minutes · A flashlightWith the engine off, look at the two battery terminals. They should be clean and tight, with no white or green crust and no movement when you nudge the cable by hand. Low voltage sets several warning lights at once on these cars. Start the car again and see whether the lights come back; if they clear but keep returning, have the battery tested, which most parts stores do free.
5 minutes · NoneStep-by-step repair walkthroughs for the fixes below are on the way.
What not to do
- Don't press the VDC OFF button just to make the warning go away; that only switches off the system that keeps you straight in a skid.
- Don't stay on a space-saver or odd-size spare any longer than you must, it can trigger these lights on its own.
- Don't ignore a SLIP light that's on with the check engine light; fix the engine fault first, because VDC shuts itself down when the engine computer has trouble.
- Don't trust a light that keeps clearing and returning. Have the codes read instead of waiting for it to settle.
What it usually turns out to be
Most likely first. Prices are typical US parts-and-labor totals for that repair, not a quote for your vehicle.
How you can tell Only VDC OFF is lit, or VDC OFF with SLIP, the car is otherwise perfectly normal, and a scan tool finds no stored faults. Pressing the button or shifting out of 4LO puts the lights out.
The repair Nothing to fix. Press the VDC OFF button back on, or take the transfer case out of low range, and restart the car.
How you can tell The ABS light is on too, the speedometer may flicker as you roll to a stop, and the code names one specific wheel. Rust, road salt or a wire rubbed through near the wheel are common on older Altimas, Pathfinders and Frontiers.
The repair The wheel comes off and that corner's sensor is replaced, or the damaged section of wiring is repaired.
How you can tell The lights began right after a battery change, jump start, alignment or steering work, and the ten-minute straight-line drive does not clear them. Codes mention the steering angle sensor.
The repair A shop relearns the sensor with a scan tool. If the sensor itself is bad it is replaced in the steering column and then calibrated.
How you can tell A handful of warning lights came on at once, often after a slow crank or a few days parked, and they clear after a drive then return. A battery test shows it is worn out or a cable end is corroded.
The repair The battery and charging system are tested, then the battery is replaced or the corroded connection is cleaned and tightened.
How you can tell The check engine light is on with SLIP and VDC OFF, and the car may idle rough, hesitate or feel flat. VDC leans on engine power control, so the system switches off when the engine computer stores a fault.
The repair The engine fault is diagnosed and repaired, for example an ignition coil, a sensor or a misfire. The SLIP and VDC OFF lights go out once the engine code is fixed and cleared.
How you can tell The lights never clear, the codes point inside the unit itself, and the brake pedal may pulse oddly at low speed. Usually only after the cheaper causes have been ruled out.
The repair The ABS and VDC actuator or control unit is replaced and then set up for your car with a scan tool.
What a shop will do
A shop starts with a scan tool that can read the ABS and VDC modules, not just engine codes, and pulls the stored faults. They check battery voltage, read the engine codes too, since an engine fault alone will shut VDC off, then watch all four wheel speed signals in live data on a short test drive to see which one drops out. Diagnosis normally runs half an hour to an hour, longer when the fault only shows up now and then.
How to reset this light
These are fault indicators, not a service reminder, so there is nothing you are meant to reset after a job. Clearing the codes turns the lights off briefly, but the system switches them straight back on when it sees the same problem. The one genuine procedure is the relearn after the battery has been disconnected or has gone flat: drive straight above about 10 mph for at least ten minutes and the lights should go out on their own. If they are still lit after that, the system has found a real fault that needs repairing.
Pressing the VDC OFF button only switches the system off and on, it does not clear a stored fault.
Common questions
What does the slip and vdc off indicators mean?
SLIP blinking as you drive means Nissan's Vehicle Dynamic Control is working to stop a wheel spinning. If SLIP stays on steady, usually alongside VDC OFF, the system has shut down, either because the VDC OFF button was pressed or because it found a fault.
Can I drive with the slip and vdc off indicators on?
Yes, carefully, in normal conditions. The car drives, steers and brakes as usual but nothing will catch a skid for you, so take extra care in rain, snow, gravel and on fast bends. If the ABS light or the check engine light is on with it, get it looked at soon rather than later.
Is it safe to drive with the SLIP and VDC OFF lights on?
In dry weather, yes, taken gently. Your brakes, steering and engine work normally and only the electronic help that catches a slide is missing. In rain, snow or on gravel the car is noticeably less forgiving, so slow down, leave more room and get the fault read.
Why did the SLIP and VDC OFF lights come on after I changed my battery?
The system lost its memory of where straight ahead is. Nissan's fix is to drive straight on a level road at more than about 10 mph for at least ten minutes, which lets it relearn. If the lights are still on after that drive, something else is wrong and the codes need reading.
My SLIP light only blinks in the rain, is that a problem?
No, that is the system doing its job. A blinking SLIP light means a wheel started to spin and the car stepped in. Treat it as a warning that the road is slicker than it looks: ease off the accelerator and keep your steering smooth.
Will my car pass inspection with the SLIP or VDC OFF light on?
The SLIP and VDC OFF lights are not emissions lights, so they do not usually fail the computer part of an emissions test on their own. A state safety inspection can fail a car with the ABS light on alongside them. Rules vary by state, so check what yours tests.
Can a bad wheel bearing or one odd tire set these lights off?
Yes to both. The wheel speed sensor often lives in the wheel bearing on these cars, so a worn bearing can take the signal with it. A spare or mismatched tire makes one wheel turn at a different speed, and the computer reads that as something wrong.
Sources: Route 23 Nissan · ManualsDir · YourMechanic