Home › Warning lights › Brake system warning light
Red: serious, act now

Brake system warning light

Also called: BRAKE light, (!) light

How urgent? Stop driving as soon as it's safe

What it means

Either the parking brake is on, or there's a problem with the brakes, most often low brake fluid.

A red light in the middle of the instrument cluster: an exclamation point inside a circle, with a curved bracket on each side. Some makes spell out BRAKE in red letters instead, and many add a separate amber P in a circle just for the parking brake. Newer cars may show a written message such as Brake fluid low or Brake system fault in the driver display.

Can I keep driving?

Release the parking brake first. If the light stays on, don't drive until it's checked. Low brake fluid can mean a leak and brakes that may not stop the car.

What to do now

  1. Make sure the parking brake is fully released.
  2. Check the brake fluid level in the reservoir under the hood.
  3. If the pedal feels soft or sinks, don't drive: have it towed.

Common causes

  • Parking brake on or its switch stuck
  • Low brake fluid from worn pads or a leak
  • Brake fluid leak at a line, hose or caliper
  • ABS or brake booster fault

Checks you can do yourself

Safe, no tools in most cases

Do these with the car parked and the engine off and cool. If anything looks or smells hot, wait.

1
Make sure the parking brake is all the way off

Push the lever fully down, or lift the foot pedal all the way up, or press the electric parking brake switch once and look for the word PARK or a P to go out. Pull it on and release it again, firmly, then look at the light. On a lot of cars this one step is the whole problem.

1 minute · None
2
Look at the brake fluid level

With the engine off and cool, open the hood and find the small see-through plastic tank on the driver's side against the firewall, usually marked with the same circle-and-exclamation-point symbol. Read the level through the side of the tank without opening the cap. It should sit between the MIN and MAX marks. Near or below MIN is the common reason this light is on.

3 minutes · None
3
Look for leaking fluid

Walk around the parked car and look at the ground where it has been sitting for wet patches. Then look at the inner face of each wheel and the back of each tire for wet streaks or dried runs. Brake fluid is clear to light brown and feels slightly oily. Any sign of it means a leak, and a leak means the brakes can run out of pressure.

5 minutes · None
4
Feel the pedal while parked

With the car parked, the engine off and the transmission in Park, press the brake pedal and hold steady pressure on it for about fifteen seconds. It should stop firm and stay put. If it slowly sinks toward the floor, or feels spongy, do not drive the car anywhere. Call for a tow instead.

2 minutes · None
5
Check what your car's manual says this light means

Look up the red brake symbol in the warning lights section of the owner's manual, for your model and year. Some cars use this one light for the parking brake, low fluid and an electronic brake fault all at once, and the manual tells you which combination of lights and chimes goes with which.

5 minutes · None

Step-by-step repair walkthroughs for the fixes below are on the way.

What not to do

  • Don't keep driving to see if it clears. This light can mean the brakes are losing fluid, and that gets worse, not better.
  • Don't just top the fluid up and move on. Brake fluid does not evaporate, so if it is low, something used it or something is leaking.
  • Don't pour in anything but the fluid type printed on the reservoir cap, usually DOT 3 or DOT 4. The wrong fluid damages seals.
  • Don't drive it if the pedal sinks or feels soft. Have it towed; that is the one symptom that most often ends in no brakes at all.

What it usually turns out to be

Most likely first. Prices are typical US parts-and-labor totals for that repair, not a quote for your vehicle.

Parking brake still partly on, or a stuck parking brake switchPrice not verified

How you can tell The light goes out, or flickers, when you pull the parking brake on and release it again. Everything else is normal: the pedal is firm, the fluid is full, and the car stops the way it always has. On older cars the little switch at the base of the lever sticks and reports the brake as on when it isn't.

The repair A shop adjusts the parking brake cable or replaces the switch at the lever or pedal. It is a small job on most cars.

Low brake fluid because the brake pads are worn outPrice not verified

How you can tell Fluid sits at or below the MIN mark, and the brakes squeal, grind or feel like they need a longer push. Looking through the wheel spokes, the pad pressed against the shiny disc looks thin, like a coin rather than a finger's width. As pads wear, fluid moves out of the tank to fill the gap, so the level drops on its own.

The repair New brake pads, and new discs if they are grooved or too thin, then the fluid is brought back to level. Usually quoted one axle at a time, front or rear.

A brake fluid leak at a line, hose or caliperPrice not verified

How you can tell The level keeps dropping after you top it up, there are wet streaks or drips near one wheel, and the pedal may travel further than it used to. Steel lines rust through underneath in salt states; rubber hoses split; the caliper, the clamp that squeezes the disc, can weep from its seal.

The repair The rusted line, split hose or leaking caliper is replaced, and then the system is bled so there is no air left in it.

Failing brake master cylinderPrice not verified

How you can tell Hold your foot on the pedal and it sinks slowly toward the floor, yet there is no puddle and nothing wet at the wheels, because the fluid is leaking past seals inside the part itself. The pedal often feels fine for the first inch and vague after that. The red light may come on alongside the amber ABS light.

The repair The master cylinder, the pump the brake pedal pushes on, is replaced and the whole system bled.

Faulty brake fluid level sensor or its wiringPrice not verified

How you can tell The fluid is clearly full between the marks, the pedal is firm, and nothing is leaking, but the light stays on anyway, or comes and goes over bumps. Unplugging and reseating the small connector on top of the fluid tank sometimes makes it flicker, which points at the sensor rather than the brakes.

The repair The level sensor, which is usually built into the reservoir cap or the side of the tank, is replaced, or a broken wire to it is repaired.

What a shop will do

A shop starts by releasing the parking brake and looking at the fluid level and its color, then plugs a scan tool into the brake and ABS computers to read any stored codes. They measure how much pad and disc is left at each wheel, look along the brake lines and hoses for wet spots or rust, and press the pedal to see whether it holds or sinks. A short road test confirms it. That first look usually takes half an hour to an hour; tracing a slow leak takes longer.

How to reset this light

This is a fault light, not a service reminder, so there is nothing to reset. Pulling a fuse, disconnecting the battery or clearing the code with a scan tool only turns the bulb off for a moment, and the car runs its own brake check every time you start it, so the light comes straight back while the fault is still there. Fix the cause, whether that is the parking brake, the fluid, the pads or a leak, and the light goes out by itself.

A few cars store a hard brake fault that a scan tool has to clear once the repair is done, so the light may need one visit to go out.

Walk through it step by step

Common questions

What does the brake system warning light mean?

Either the parking brake is on, or there's a problem with the brakes, most often low brake fluid.

Can I drive with the brake system warning light on?

Release the parking brake first. If the light stays on, don't drive until it's checked. Low brake fluid can mean a leak and brakes that may not stop the car.

Can I drive with the red brake light on?

Only after you have proved it is the parking brake. Release the parking brake fully; if the light goes out, drive on. If it stays on, treat the car as unsafe until someone checks the fluid and the pedal, because this light also means the brakes may be losing the pressure they need to stop you.

My brake light is on but the brakes feel completely normal. Why?

The usual answers are a parking brake that is not fully released, a fluid level that has crept just below the sensor as the pads wear, or a bad level sensor. Brakes can feel normal right up until they don't, so it is still worth checking the fluid and the pad thickness rather than waiting.

Will my car pass inspection with the brake warning light on?

In states that do a safety inspection, a lit red brake warning light is a standard fail, and so is a brake fluid leak or pads worn past the limit. Rules differ by state, so check your own state's inspection list, but plan on fixing it first.

Does the brake warning light reset itself?

Yes, once the real problem is gone. Release a stuck parking brake or bring the fluid back to level and the light usually goes out within a few seconds or on the next start. If it goes out and then returns, the fault is still there and the car is finding it again.

Can I just add brake fluid myself?

You can top it to the MAX line with the exact fluid type printed on the cap, and that is worth doing so you have brakes to get it looked at. But low fluid is a symptom, not the problem: it went somewhere, either into worn pads or out through a leak, and that still needs finding.

Sources: J.D. Power · NuBrakes

Not your light? These get mixed up with it

Symbols vary a little between makes. Your owner's manual shows the exact lights for your vehicle. This is a general guide, not a diagnosis.