Home › Warning lights › Brake pad wear light
Amber/yellow: check soon

Brake pad wear light

Also called: Brake pad wear sensor warning, Brake wear indicator, Check brake pads, Brake linings worn, Brake pad warning

How urgent? Get it checked soon

What it means

A sensor in the brake pads reports that the friction material has worn down to its limit. The brakes still work, but the pads are at the end of their life and need replacing.

An amber circle standing for the brake disc, with short broken or dashed lines curving away from each side for the pads, sometimes with an exclamation mark inside. It looks much like the red brake system light, but that one has solid curved lines and is far more urgent. Many European cars show words instead, such as Brake pad wear or Check brake pads.

Can I keep driving?

Yes, carefully, for a short time. The light comes on with a little material left, not none, so a few hundred miles of gentle driving is normally fine while you get an appointment. Stop driving and get it towed if you hear grinding or metal scraping when you brake, or if the pedal feels different, because that means the pads are gone and stopping distances are getting longer.

What to do now

  1. Look at the pads through the wheel spokes: a sliver of material thinner than a stack of two quarters means they are done.
  2. Listen when you brake. A squeal means worn, a grinding or scraping noise means stop driving.
  3. Book brake work now and expect both wheels on that axle to be done together.
  4. Have the wear sensor replaced at the same time, or the light will come straight back.

Common causes

  • Brake pads worn down to their limit through normal use
  • Wear sensor not replaced with the last set of pads
  • Sensor wire cut, pinched or unplugged during a previous brake job
  • One pad worn fast by a sticking caliper or seized slide pins
  • Broken wiring or a corroded connector in the sensor circuit
  • Pads replaced but the service indicator never reset on makes that need it

Checks you can do yourself

Safe, no tools in most cases

Do these with the car parked and the engine off and cool. If anything looks or smells hot, wait.

1
Look at the pads through the wheel

Stand beside the parked car and look through the gaps in the wheel at the shiny disc. You will see the pad squeezed against it inside a metal bracket. What you are judging is the thickness of the dark friction block, ignoring the steel backing plate behind it. Anything thinner than about an eighth of an inch is finished. Do all four wheels, turning the steering to full lock first to see the front ones better.

10 minutes · A flashlight
2
Listen to what the brakes are telling you

Drive gently somewhere quiet with the windows down and brake a few times. A high pitched squeal as you slow down is the built in wear tab doing its job and matches the light. A deep grinding or scraping, or a noise you can feel through the pedal, means the material is gone and steel is cutting the disc. In that case stop driving it.

10 minutes · None
3
Check the brake fluid level

With the car parked and cool, find the small reservoir with a brake symbol on the cap, usually at the back of the engine bay on the driver's side, and read the level against the markings on the side without opening it. Worn pads make the level sit slightly lower than normal. A level well below the minimum points at a leak instead, which is a different and much more serious problem.

5 minutes · None
4
Compare one corner against the others

Look at the pad thickness at every wheel and note any corner that is much worse than the rest. After a normal drive, hold the back of your hand near each wheel without touching it; one that throws off noticeably more heat than the others suggests a brake that is dragging. Tell the shop which corner it was, because that changes the repair from pads to a caliper.

10 minutes · None
5
Read the service menu on European cars

BMW, Mercedes, Volvo, Audi and some others show remaining brake pad life in the driver information menu, often as a mileage or a bar graph. Scroll through with the steering wheel buttons until you find the brake or service entry. It gives you a real number to work with instead of guessing from the light.

5 minutes · None

Step-by-step repair walkthroughs for the fixes below are on the way.

What not to do

  • Don't ignore grinding or scraping; that is steel cutting into the disc and it makes the car stop worse.
  • Don't just clear the message and move on. Pads do not get thicker because a warning was dismissed.
  • Don't have pads done on one wheel only. Both wheels on an axle are always replaced together.
  • Don't tow, carry heavy loads or take long downhill runs while this light is on.

What it usually turns out to be

Most likely first. Prices are typical US parts-and-labor totals for that repair, not a quote for your vehicle.

Brake pads worn out from normal usePrice not verified

How you can tell Material visible through the wheel is down to a thin sliver, there is often a squeal when braking, and the mileage since the last brake job is high. Fronts usually wear out first because they do most of the stopping. This is the reason nearly every time.

The repair New pads and a new wear sensor on that axle, with the caliper slide pins cleaned and greased and the brake fluid topped off. Figures below are for one axle, front or rear.

Pads and discs both worn outPrice not verified

How you can tell Very common once the warning has been on a while, or if there was any grinding. The disc face feels ridged or has a lip you can catch a fingernail on, and there may be a pulse through the pedal when you slow down.

The repair New pads, discs and wear sensor on that axle. Modern discs are usually replaced rather than machined. Again this is per axle, and trucks and performance cars sit at the top of the range.

Wear sensor damaged or never replacedPrice not verified

How you can tell The pads measure healthy but the light is on, or the warning appeared right after a brake job. The sensor is a thin wire looped into the pad, and it is easy to tear or leave unplugged. Sometimes the connector is simply hanging loose.

The repair Fit a new wear sensor, or repair and reconnect the plug. The part itself is cheap; most of the cost is pulling the wheel and the labor time to get at it.

Sticking caliper or seized slide pinsPrice not verified

How you can tell One corner is worn far more than the rest, that wheel runs hotter than the others after a drive, and the car may pull slightly or feel like it is dragging. Fuel economy often drops and there can be a smell after a long run.

The repair Free off or replace the caliper, clean and grease the slide pins or fit a new bracket, then new pads and usually a new disc on that side because of the uneven wear.

Wiring or connector fault in the sensor circuitPrice not verified

How you can tell The warning comes and goes, or shows up after work near the suspension or after driving through deep water or road salt. The pads look fine and the sensor itself is intact, but the wire running up to the car is chafed or green with corrosion.

The repair Trace and repair the wire or replace the connector and pigtail. Diagnosis is most of the cost here, because the fault has to be found before it can be fixed.

What a shop will do

The shop takes the wheels off and measures what is left of the friction material on every pad with a gauge, usually against a limit of around two millimeters, under a tenth of an inch. They measure the discs for thickness and for warping, check that the calipers and slide pins move freely, and look at how evenly each pad has worn, because one odd corner changes the diagnosis. If the pads turn out to be fine they test the sensor and its wiring. A brake inspection like this is normally about half an hour, and many shops fold the charge into the repair.

How to reset this light

There is nothing to reset in the usual sense. The light is reporting the actual thickness of your brake pads, and clearing the message does not add material back; it returns as soon as the car checks the sensor again, often within a mile. The only real reset comes after the pads and the sensor have genuinely been replaced: on BMW, Mercedes, Volvo and some other makes the brake service indicator then has to be reset through the dash menu or with a scan tool before the message clears for good. On most Japanese and American cars it simply goes out by itself once a new sensor is fitted.

If the warning switches itself off while the pads are still thin, suspect a broken sensor wire rather than good news.

Common questions

What does the brake pad wear light mean?

A sensor in the brake pads reports that the friction material has worn down to its limit. The brakes still work, but the pads are at the end of their life and need replacing.

Can I drive with the brake pad wear light on?

Yes, carefully, for a short time. The light comes on with a little material left, not none, so a few hundred miles of gentle driving is normally fine while you get an appointment. Stop driving and get it towed if you hear grinding or metal scraping when you brake, or if the pedal feels different, because that means the pads are gone and stopping distances are getting longer.

How long can I drive with the brake pad wear light on?

Usually a few hundred miles of ordinary driving, because the sensor triggers with a little material still left. Treat it as a reason to book the work this week, not this month. The moment you hear grinding, that window has closed and the car should not be driven.

Is the brake pad wear light the same as the red brake warning light?

No. This amber one means the pads are worn and the brakes still work normally. A red brake light means the parking brake is on or the brake system itself has a problem, most often low fluid from a leak, and that one means do not drive the car until it is checked.

Will a brake pad warning light fail an inspection?

The light itself is not usually what fails you, but in states with a safety inspection the inspector measures pad thickness, and pads worn to the warning point will often fail. Grooved or undersized discs fail as well. Getting the brakes done first is the cheaper order to do things in.

Why is the light still on after I put new brake pads in?

Almost always one of two things: the old wear sensor was reused or left unplugged, or the car needs its brake service indicator reset through the dash. The sensor is a one-use item on most cars, so it goes in with every set of pads.

The brakes squeal but no light came on. Does that mean anything?

Yes, it often means exactly the same thing. Many cars have no pad warning light and use a small metal tab on the pad that scrapes the disc to make a squeal when the material gets low. If the squeal happens whenever you brake and goes quiet when you let off, have the pads measured.

Sources: RepairSmith · YourMechanic · AAA

Not your light? These get mixed up with it

Symbols vary a little between makes. Your owner's manual shows the exact lights for your vehicle. This is a general guide, not a diagnosis.