Home › Warning lights › Electronic parking brake fault light
Amber/yellow: check soon

Electronic parking brake fault light

Also called: EPB light, Electric parking brake fault, Park brake malfunction, Amber P light, Auto hold fault light

How urgent? Get it checked soon

What it means

The car has found a fault in the electric parking brake, the one worked by a small button or switch instead of a lever. The brake may not hold the car, or may not fully release.

It shows in the main cluster near the other brake lights: an amber circle with a P inside, usually with small brackets on each side and often an exclamation mark. Several makes show no symbol at all and instead light the general amber warning lamp with a written message such as park brake malfunction or service parking brake. The matching red P light is the normal one that means the brake is applied.

Can I keep driving?

You can usually drive, because this brake is only for parking, not for stopping. Expect it not to hold on a slope: leave the car in Park, or in gear on a manual, and turn the wheels into the curb. If a rear wheel drags, smells hot or the car will not move freely, stop and have it towed on a flatbed.

If it's flashing or blinking: On some cars the parking brake light blinks rather than staying on. A blinking light means the brake has not finished applying or releasing, so the car is not being held properly. Set it and release it once more, and if it keeps blinking, do not leave the car on a slope relying on it.

What to do now

  1. Park, then press the brake pedal and cycle the parking brake switch off and on twice to see if the light clears.
  2. If the car is a plug-in or electric, make sure the charging cable is unplugged.
  3. Have the 12-volt battery tested, as a weak battery sets this light off on many cars.
  4. If the brake will not release or a rear wheel drags, don't force it: get it towed to a shop.

Common causes

  • Failed actuator motor on a rear brake caliper
  • Weak or dying 12-volt battery
  • Broken parking brake switch
  • Worn rear brake pads or a stuck caliper
  • Damaged wiring or a corroded connector at a rear wheel
  • Parking brake or ABS control module fault

Checks you can do yourself

Safe, no tools in most cases

Do these with the car parked and the engine off and cool. If anything looks or smells hot, wait.

1
Cycle the parking brake switch

Park on flat ground, leave the car running and in Park, and keep your foot firmly on the brake pedal. Press the parking brake switch down to release, then pull it up to set, then release it again. Do that twice. Many cars clear a one-off glitch this way. If the light is still on after two tries, stop: pressing it over and over will not help.

3 minutes · None
2
Unplug the charging cable

On electric and plug-in hybrid cars the parking brake is held on deliberately while the charging cable is connected, and a cable that is still plugged in or not seated properly can look like a fault. Unplug it at the car, close the charge flap, then start the car and look at the light again.

2 minutes · None
3
Check the 12-volt battery

A weak 12-volt battery sets this light off on a lot of cars, especially after the car has sat for a while or been jump started. With the engine off, look at the two battery terminals: they should be clean and tight enough that you cannot twist the clamp by hand. If the engine cranks slowly or the lights dim, get the battery and charging system tested free at a parts store.

10 minutes · None
4
Feel for a dragging rear wheel

Drive slowly a few minutes, park, and hold the back of your hand a few inches away from each rear wheel without touching the brake parts. If one side gives off much more heat than the other, or there is a hot metal smell, the parking brake is still clamped on that corner. Don't keep driving it: that cause ruins pads and rotors quickly.

10 minutes · None
5
Look up your car's own message

Open the owner's manual, or the PDF version on your phone, and find the warning light pages. Makes word this differently and some tell you a specific recovery step, such as how to release the brake manually or that the car must go on a flatbed. It also tells you whether your car has auto hold, which uses the same system and the same light.

10 minutes · Owner's manual

Step-by-step repair walkthroughs for the fixes below are on the way.

What not to do

  • Don't park on a hill trusting this brake: use Park or first gear and turn the front wheels into the curb.
  • Don't jab the switch repeatedly if the brake won't release: you can overheat the little motors at the rear wheels.
  • Don't try to drag the car along with the brake stuck on: have it flatbedded instead.
  • Don't let a shop fit rear brake pads without a scan tool, as the brake motors must be wound back and reset electronically.

What it usually turns out to be

Most likely first. Prices are typical US parts-and-labor totals for that repair, not a quote for your vehicle.

Failed parking brake actuator motor at a rear wheelPrice not verified

How you can tell You hear the whirring noise from only one side, or from neither, when the brake sets. The car usually stores a code naming the left or right actuator circuit, and that same wheel may stay clamped or never clamp at all.

The repair Replace the actuator motor, or the whole rear caliper on cars where the motor is built in, then recalibrate the system with a scan tool.

Weak or failing 12-volt batteryPrice not verified

How you can tell The light shows up with a handful of other warnings at once, often after the car sat for a week or was jump started, and the engine cranks slowly. A battery test at a parts store shows it down on cranking power.

The repair Replace the battery, and on many European cars register the new one to the car so the charging system treats it correctly.

Broken parking brake switchPrice not verified

How you can tell The switch feels dead or loose, nothing happens when you press it, and the code points to the switch circuit rather than a wheel. Common on cars where the switch sits next to the gear lever and gets knocked.

The repair Replace the switch assembly in the console, then check that the brake sets and releases normally.

Worn rear brake pads or a sticking caliperPrice not verified

How you can tell The brake motors run longer than normal or stall out because there is nothing left to clamp, and you hear grinding when braking. One rear wheel may run hot and the car pulls slightly.

The repair Replace the rear pads, and rotors if needed, with the parking brake motors retracted by a scan tool, then reset the system.

Damaged wiring or corroded connector at a rear wheelPrice not verified

How you can tell The light comes and goes, often over bumps or after rain, and the code jumps between an open and a short on one actuator. The flexible loom that runs to the rear caliper is a known rub and corrosion point.

The repair Repair or replace the damaged section of wiring and the connector, then clear the code and test the brake.

Parking brake or ABS control module faultPrice not verified

How you can tell It shows up with the ABS and traction control lights together, and the scan tool cannot talk to the brake module or reports an internal failure inside it.

The repair Replace the control module and program it to the car, which needs dealer-level software on most makes.

What a shop will do

A shop plugs in a scan tool that can talk to the parking brake module, reads the stored codes, and watches the live data while they command the brake on and off. That tells them straight away whether a wheel actuator is answering, whether the switch is sending a signal, and whether system voltage dropped. They check battery condition and rear pad thickness at the same time. Reckon on half an hour to an hour of diagnosis.

How to reset this light

This is a fault light, not a service reminder, so there is nothing for you to reset. Clearing the code with a scan tool or pulling the battery cable may make the light go out for a trip, but it comes back as soon as the car tests the brake again, and in the meantime the brake still may not hold. After a real repair the shop has to run the parking brake relearn or calibration with a scan tool, which winds the motors back out to the right position.

Cars with auto hold use the same system, so that feature usually stops working until the fault is fixed.

Common questions

What does the electronic parking brake fault light mean?

The car has found a fault in the electric parking brake, the one worked by a small button or switch instead of a lever. The brake may not hold the car, or may not fully release.

Can I drive with the electronic parking brake fault light on?

You can usually drive, because this brake is only for parking, not for stopping. Expect it not to hold on a slope: leave the car in Park, or in gear on a manual, and turn the wheels into the curb. If a rear wheel drags, smells hot or the car will not move freely, stop and have it towed on a flatbed.

Can I drive with the electronic parking brake light on?

Usually yes for short trips, because this brake only holds the car when parked and does not stop you on the road. The catch is that it may not hold on a slope, so always leave the car in Park and turn the wheels into the curb. If a rear wheel drags or smells hot, stop driving and have it towed.

How do I release an electronic parking brake that is stuck on?

Try the normal release once more with the engine running, your foot on the brake pedal and the car in Park, then check that no charging cable is plugged in and that the 12-volt battery is not flat. If it still will not let go, stop there. Most makes say the car has to go on a flatbed, because the release is done through the brake module with a scan tool.

Will my car pass inspection with an EPB fault light on?

In states that inspect brakes or look at dashboard warning lights, an amber parking brake fault is likely to fail, and a parking brake that does not hold the car fails on its own in states that test it. Expect to fix the cause first.

Does the light go off by itself if I disconnect the battery?

It might go out for a short while, but it is not fixed. The car retests the parking brake every time you use it and relights the warning when it finds the same problem. Disconnecting the battery can also cost you radio presets and make a weak battery situation worse.

Why did this light come on right after I changed my rear brakes?

The parking brake motors have to be wound back electronically before the rear pads come out, and wound back in and calibrated afterwards. If that was skipped, or done by hand, the system reads the wrong position and sets the fault. A shop with the right scan tool can usually run the calibration and clear it.

Sources: Volkswagen · Kia owner's manual · YourMechanic

Not your light? These get mixed up with it

Symbols vary a little between makes. Your owner's manual shows the exact lights for your vehicle. This is a general guide, not a diagnosis.