BMW 6 / 8 Seriesproblems, repair costs and recalls
Problems reported across 2004–2026. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
35 documented issues across all years, most serious first.
Worn valve stem seals make the V8 burn oil
- What you'll notice
- Blue-gray smoke from the exhaust at startup or after coasting, and needing to add oil between changes.
- Why it happens
- The rubber valve stem seals on the N62 V8 harden from engine heat and let oil slip into the cylinders.
- What to do
- Track how much oil the car uses. Small amounts can be lived with; heavy smoke or fouled spark plugs mean the seals need replacing, which is a big labor job.
Plastic cooling parts crack and the engine overheats
- What you'll notice
- Coolant leaks, a sweet smell, white crust on hose connections, the low-coolant warning, or rising engine temperature.
- Why it happens
- The thermostat housing, radiator end tanks, water pump impeller and hoses are plastic and become brittle after years of heat cycles.
- What to do
- Don't keep driving if the engine overheats. If there's no record of a cooling system refresh, budget to replace the aging parts as a set.
SMG gearbox pump fails on the M6
- What you'll notice
- The car won't select a gear, gets stuck in one gear, shows a transmission warning, or won't start.
- Why it happens
- The M6's automated manual (SMG) gearbox shifts using a hydraulic pump that wears out with age. Its clutch also wears faster than a normal manual.
- What to do
- Have a BMW M specialist read the SMG codes and test the pump. Budget for clutch replacement every 60,000 to 80,000 miles depending on use.
Rod bearing wear on the M6 V10
- What you'll notice
- Often no sign until it's serious. Later, knocking from the engine, low oil pressure warnings, or metal in the oil.
- Why it happens
- The high-revving S85 V10 wears its connecting rod bearings as mileage builds. A failed bearing can destroy the engine.
- What to do
- Keep oil changes frequent and ask for proof of bearing service. Many M specialists replace the bearings as preventive maintenance.
Engine computer can stall the engine (recall)
- What you'll notice
- The engine stalls and may not restart; steering and brakes get heavy.
- Why it happens
- Some engine management control units were not built to specification.
- What to do
- Check your VIN with a BMW dealer; the unit is replaced free.
Free at a BMW dealer. Check your VIN to see if it was already done.
Static discharge can stall the V8 in cold weather (recall)
- What you'll notice
- The engine stalls, usually in cold, dry weather.
- Why it happens
- Static electricity at the fuel rails can disturb the engine computer.
- What to do
- Have a BMW dealer confirm that the extra ground cables were installed.
Free at a BMW dealer. Check your VIN to see if it was already done.
Brake vacuum pump valve can leak oil and weaken the brakes (recall)
- What you'll notice
- The brake pedal gets harder to push and the car takes longer to stop.
- Why it happens
- A check valve in the brake vacuum pump can leak oil into the brake booster over time, reducing power assist.
- What to do
- Check your VIN with a BMW dealer to confirm the recall work was done.
Free at a BMW dealer. Check your VIN to see if it was already done.
Twin-turbo V8 burns oil from worn valve stem seals
- What you'll notice
- Blue smoke at startup or when slowing down, an oil smell, and the oil level dropping quickly.
- Why it happens
- On the 650i's N63 V8 the turbos sit between the cylinder banks, and that heat wears out valve stem seals early.
- What to do
- Check oil often. Ask whether BMW's Customer Care Package updates were done. Heavy smoking means the seals need replacing.
Turbochargers fail on the 650i
- What you'll notice
- Loss of power, a whining or siren noise, smoke, or oil in the intake.
- Why it happens
- The hot-V layout cooks the turbochargers and their oil lines, so they wear out sooner than on other engines.
- What to do
- Have boost and oil leaks checked at the first sign. Turbo replacement on this V8 is a big job.
High-pressure fuel pump fails
- What you'll notice
- Long cranking, rough idle, hesitation, misfires, or the engine dropping into reduced power.
- Why it happens
- The high-pressure pump that feeds the direct-injection system wears internally.
- What to do
- Have fuel pressure codes read. A failing pump is replaced; ask the dealer about any extended coverage.
Thermostat and plastic coolant pipes fail on the 640i
- What you'll notice
- The temperature gauge swings, coolant goes missing, or an overheating warning appears.
- Why it happens
- The electric thermostat and plastic coolant pipes on the N55 are weak points.
- What to do
- Stop if the engine overheats. Above about 80,000 miles many owners replace the cooling parts as a set.
Rod bearing wear on the M6
- What you'll notice
- Knocking at idle or under load.
- Why it happens
- The M6's S63 V8 rod bearings can wear early, especially on cars used on track.
- What to do
- Have oil analysis and a specialist inspection done. Preventive bearing replacement is common.
Auxiliary water pump can overheat and catch fire (recall)
- What you'll notice
- Usually no warning. Possibly smoke or a burning smell from the engine bay.
- Why it happens
- The circuit board in the electric auxiliary water pump that cools the turbos can overheat.
- What to do
- Check your VIN for open recalls. Park outdoors until the pump is replaced.
Free at a BMW dealer. Check your VIN to see if it was already done.
Fuel pump wiring in the tank can fail and stall the engine (recall)
- What you'll notice
- The engine stalls or won't start, or there is a fuel smell.
- Why it happens
- Crimped wire contacts on the in-tank fuel pump can loosen, melt the connector or stop the pump.
- What to do
- Have a BMW dealer check your VIN; the fuel pump module is replaced free.
Free at a BMW dealer. Check your VIN to see if it was already done.
Driver airbag inflator can rupture (recall)
- What you'll notice
- No warning. The problem only shows in a crash.
- Why it happens
- A manufacturing defect can make the driver's airbag inflator rupture when it deploys, throwing metal pieces.
- What to do
- Get the recall done as soon as possible; the driver airbag is replaced free.
Free at a BMW dealer. Check your VIN to see if it was already done.
Seat side airbags may not deploy (recall)
- What you'll notice
- No warning. The problem only shows in a crash.
- Why it happens
- The igniters in the seat-mounted side airbags may not fire.
- What to do
- Check your VIN with BMW; the airbag modules are replaced free.
Free at a BMW dealer. Check your VIN to see if it was already done.
Transmission control unit can leak and cut power (recall)
- What you'll notice
- Sudden loss of drive power or a transmission warning.
- Why it happens
- A weld seam on the transmission control unit cover can let fluid into the electronics.
- What to do
- Have the recall done. Dealers replace the module and fluid as needed.
Free at a BMW dealer. Check your VIN to see if it was already done.
Starter can overheat and catch fire (recall)
- What you'll notice
- A starter that won't turn the engine, followed by a burning smell after repeated tries.
- Why it happens
- If the starter fails and the driver keeps trying to start the car, the starter can overheat and ignite nearby parts.
- What to do
- Don't keep cranking a car that won't start. Check your VIN; dealers update software and replace the starter free.
Free at a BMW dealer. Check your VIN to see if it was already done.
Driveshaft connection to the rear differential can fail (recall)
- What you'll notice
- Loss of power to the rear wheels, or the car rolling if the parking brake isn't set.
- Why it happens
- The connection between the driveshaft and rear differential may be damaged.
- What to do
- Always set the parking brake. Have a BMW dealer inspect and repair it under the recall.
Free at a BMW dealer. Check your VIN to see if it was already done.
Twin-turbo V8 burns or leaks oil on the M850i
- What you'll notice
- Oil spots or oil in the engine bay, bluish smoke from the exhaust, or adding a quart every few thousand miles.
- Why it happens
- The turbos sit between the cylinder heads and run very hot, wearing seals and gaskets.
- What to do
- Keep track of oil use. Gasket leaks are cheap to fix; valve stem seal work is a much bigger job.
Valve cover and oil filter housing gaskets leak oil
- What you'll notice
- Burning oil smell, light smoke from the engine bay, and oil on the engine or the belly pan.
- Why it happens
- The gaskets on the valve covers and oil filter housing shrink and harden with age. On the V8 the job takes longer because of how the engine is packed in.
- What to do
- Have the leak found and fixed before oil reaches the exhaust or soaks the belts and alternator.
Automatic transmission shifts harshly or leaks fluid
- What you'll notice
- Harsh, late or jerky shifts, delayed engagement into drive or reverse, or red fluid under the car.
- Why it happens
- The ZF 6-speed automatic's fluid was sold as lifetime, so it often never gets changed. Worn solenoids, old fluid and a leaking plastic sleeve where the wiring enters the transmission are common causes.
- What to do
- Have the fluid level checked and the codes read. A fluid and filter change, new sleeve and pan gasket, and a software update fix many cases.
Throttle actuators fail on the M6
- What you'll notice
- Surging, a sudden drop into limp mode, warning lights, or the car refusing to accelerate.
- Why it happens
- The V10 uses motor-driven throttle actuators whose internal gears and circuit boards wear out.
- What to do
- Have the codes read. A failed actuator is replaced and the throttle system recalibrated.
Convertible top stops or works slowly
- What you'll notice
- The soft top moves slowly, stops partway, won't latch, or won't open or close at all.
- Why it happens
- The top runs on a hydraulic pump and cylinders with small position switches. Pumps wear out, cylinder seals leak, and switches fail.
- What to do
- Test the top several times before buying. Have a specialist read the top codes before replacing big parts; a switch or leaking cylinder is often the cause.
Battery drains overnight
- What you'll notice
- The car won't start after sitting, or shows battery drain warnings.
- Why it happens
- Some modules, such as the comfort access and trunk release modules, may not go to sleep and keep drawing power.
- What to do
- Have the battery tested and a parasitic drain test done. A BMW scan tool helps find which module stays awake.
Front control arm bushings wear and the wheel shakes when braking
- What you'll notice
- Clunks over bumps, a steering wheel shake when braking, loose steering, or uneven tire wear.
- Why it happens
- The front control arm bushings on these heavy coupes and convertibles crack and wear out with age and mileage.
- What to do
- Have the front suspension checked. New arms or bushings and an alignment usually fix it.
Fuel injectors fail on the 650i V8
- What you'll notice
- Rough running, misfires, a fuel smell, or a check engine light.
- Why it happens
- Deposits build on the injector tips, or the injectors fail electrically.
- What to do
- Get misfire codes diagnosed. Injectors are often replaced in sets.
Valve cover and oil separator leak on the 640i
- What you'll notice
- A burning oil smell and oily residue on top of the engine.
- Why it happens
- Heat cycles break down the valve cover gasket and the built-in crankcase vent system on the N55 engine.
- What to do
- Have it repaired before oil gets on the exhaust or ignition coils.
Rearview camera image can go missing (recall)
- What you'll notice
- Part or all of the backup camera picture is missing when reversing.
- Why it happens
- Camera software or settings can leave the rearview image blank or blocked.
- What to do
- Have a BMW dealer update the camera software.
Free at a BMW dealer. Check your VIN to see if it was already done.
Front tires wear out fast on the edges
- What you'll notice
- Inner or outer edges of the front tires wear down quickly, sometimes in about 10,000 miles.
- Why it happens
- The factory alignment settings are hard on tires, especially on xDrive cars.
- What to do
- Check the inner tire edges often. A specialist alignment or longer-wearing tires can help.
Low coolant warning or coolant leaks
- What you'll notice
- A low-coolant warning that comes and goes, or coolant drips under the car.
- Why it happens
- New engines absorb some coolant into seals, which BMW says is normal. Plastic hoses, the expansion tank and turbo coolant lines can also leak.
- What to do
- Top up with BMW coolant. If the warning keeps returning, have the system pressure-tested for leaks.
Valve cover and crankcase vent valve leak on the 3.0L six
- What you'll notice
- Oil leaks, a burning oil smell, a whistle from the engine, rough idle, or a puff of smoke.
- Why it happens
- The crankcase vent (PCV) valve is built into the plastic valve cover on the B58 engine, and the cover's gasket can leak.
- What to do
- Have the valve cover and vent valve checked. A failed vent valve means replacing the whole valve cover.
iDrive screen freezes, reboots or goes blank
- What you'll notice
- The center screen freezes, restarts by itself, goes black, or phones won't connect.
- Why it happens
- Early iDrive units in particular are known for software and hardware faults; later units are better but can still lock up.
- What to do
- Try a system reset and ask a dealer for the latest software. If the unit has failed, a used or later-version unit is often the fix.
Trunk seals leak and the carpet gets wet
- What you'll notice
- Wet carpet or water in the trunk.
- Why it happens
- The trunk seals are known to fail on this generation.
- What to do
- Have the seals replaced and dry the trunk out to prevent electrical damage.
Brakes squeal when coming to a stop
- What you'll notice
- A loud squeal when slowing from about 30 mph to a stop, even on fairly new cars. Stopping power is normal.
- Why it happens
- Brake dust and the factory pad material are the suspected cause, especially with the M Sport brakes.
- What to do
- Have the brakes checked. Many owners switch to aftermarket pads to quiet them.
Repair prices for your BMW 6 / 8 Series
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace valve stem seals (both cylinder banks)
- Replace water pump and thermostat
- Replace valve cover gaskets
- Replace mechatronic sleeve, filter pan and fluid
- Replace connecting rod bearings and rod bolts (preventive or at first sign of wear)
- Rebuild or replace failed throttle actuator(s) and recalibrate
- Diagnose and update or replace iDrive head unit
- Repair convertible top hydraulic pump or cylinder
- Diagnose parasitic drain and replace battery
- Replace front control arms (pair) and align
- Replace valve stem seals (twin-turbo V8)
- Replace one turbocharger (rebuilt BMW unit)
- Replace high-pressure fuel pump
- Replace fuel injectors
- Replace valve cover with gasket
- Replace thermostat
- Replace trunk seal
- Replace front brake pads and wear sensor
- Replace valve cover with built-in vent valve
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Recall repair at a BMW dealerNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.