Your 2010 BMW 6 / 8 Seriesproblems, repair costs and recalls
What we've documented about the 2010 BMW 6 / 8 Series: problems owners and shops report, typical repair and upkeep costs, and safety recalls.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems for your 2010 BMW 6 / 8 Series
12 documented issues apply to 2010, most serious first.
Worn valve stem seals make the V8 burn oil
- What you'll notice
- Blue-gray smoke from the exhaust at startup or after coasting, and needing to add oil between changes.
- Why it happens
- The rubber valve stem seals on the N62 V8 harden from engine heat and let oil slip into the cylinders.
- What to do
- Track how much oil the car uses. Small amounts can be lived with; heavy smoke or fouled spark plugs mean the seals need replacing, which is a big labor job.
Plastic cooling parts crack and the engine overheats
- What you'll notice
- Coolant leaks, a sweet smell, white crust on hose connections, the low-coolant warning, or rising engine temperature.
- Why it happens
- The thermostat housing, radiator end tanks, water pump impeller and hoses are plastic and become brittle after years of heat cycles.
- What to do
- Don't keep driving if the engine overheats. If there's no record of a cooling system refresh, budget to replace the aging parts as a set.
SMG gearbox pump fails on the M6
- What you'll notice
- The car won't select a gear, gets stuck in one gear, shows a transmission warning, or won't start.
- Why it happens
- The M6's automated manual (SMG) gearbox shifts using a hydraulic pump that wears out with age. Its clutch also wears faster than a normal manual.
- What to do
- Have a BMW M specialist read the SMG codes and test the pump. Budget for clutch replacement every 60,000 to 80,000 miles depending on use.
Rod bearing wear on the M6 V10
- What you'll notice
- Often no sign until it's serious. Later, knocking from the engine, low oil pressure warnings, or metal in the oil.
- Why it happens
- The high-revving S85 V10 wears its connecting rod bearings as mileage builds. A failed bearing can destroy the engine.
- What to do
- Keep oil changes frequent and ask for proof of bearing service. Many M specialists replace the bearings as preventive maintenance.
Brake vacuum pump valve can leak oil and weaken the brakes (recall)
- What you'll notice
- The brake pedal gets harder to push and the car takes longer to stop.
- Why it happens
- A check valve in the brake vacuum pump can leak oil into the brake booster over time, reducing power assist.
- What to do
- Check your VIN with a BMW dealer to confirm the recall work was done.
Free at a BMW dealer. Check your VIN to see if it was already done.
Valve cover and oil filter housing gaskets leak oil
- What you'll notice
- Burning oil smell, light smoke from the engine bay, and oil on the engine or the belly pan.
- Why it happens
- The gaskets on the valve covers and oil filter housing shrink and harden with age. On the V8 the job takes longer because of how the engine is packed in.
- What to do
- Have the leak found and fixed before oil reaches the exhaust or soaks the belts and alternator.
Automatic transmission shifts harshly or leaks fluid
- What you'll notice
- Harsh, late or jerky shifts, delayed engagement into drive or reverse, or red fluid under the car.
- Why it happens
- The ZF 6-speed automatic's fluid was sold as lifetime, so it often never gets changed. Worn solenoids, old fluid and a leaking plastic sleeve where the wiring enters the transmission are common causes.
- What to do
- Have the fluid level checked and the codes read. A fluid and filter change, new sleeve and pan gasket, and a software update fix many cases.
Throttle actuators fail on the M6
- What you'll notice
- Surging, a sudden drop into limp mode, warning lights, or the car refusing to accelerate.
- Why it happens
- The V10 uses motor-driven throttle actuators whose internal gears and circuit boards wear out.
- What to do
- Have the codes read. A failed actuator is replaced and the throttle system recalibrated.
Convertible top stops or works slowly
- What you'll notice
- The soft top moves slowly, stops partway, won't latch, or won't open or close at all.
- Why it happens
- The top runs on a hydraulic pump and cylinders with small position switches. Pumps wear out, cylinder seals leak, and switches fail.
- What to do
- Test the top several times before buying. Have a specialist read the top codes before replacing big parts; a switch or leaking cylinder is often the cause.
Battery drains overnight
- What you'll notice
- The car won't start after sitting, or shows battery drain warnings.
- Why it happens
- Some modules, such as the comfort access and trunk release modules, may not go to sleep and keep drawing power.
- What to do
- Have the battery tested and a parasitic drain test done. A BMW scan tool helps find which module stays awake.
Front control arm bushings wear and the wheel shakes when braking
- What you'll notice
- Clunks over bumps, a steering wheel shake when braking, loose steering, or uneven tire wear.
- Why it happens
- The front control arm bushings on these heavy coupes and convertibles crack and wear out with age and mileage.
- What to do
- Have the front suspension checked. New arms or bushings and an alignment usually fix it.
iDrive screen freezes, reboots or goes blank
- What you'll notice
- The center screen freezes, restarts by itself, goes black, or phones won't connect.
- Why it happens
- Early iDrive units in particular are known for software and hardware faults; later units are better but can still lock up.
- What to do
- Try a system reset and ask a dealer for the latest software. If the unit has failed, a used or later-version unit is often the fix.
Repair prices for your 2010 BMW 6 / 8 Series
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace valve stem seals (both cylinder banks)
- Replace water pump and thermostat
- Replace valve cover gaskets
- Replace mechatronic sleeve, filter pan and fluid
- Replace connecting rod bearings and rod bolts (preventive or at first sign of wear)
- Rebuild or replace failed throttle actuator(s) and recalibrate
- Diagnose and update or replace iDrive head unit
- Repair convertible top hydraulic pump or cylinder
- Diagnose parasitic drain and replace battery
- Replace front control arms (pair) and align
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Recall repair at a BMW dealerNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Checking the NHTSA recall database…