Chrysler Sebringproblems, repair costs and recalls
Problems reported across 1996–2010. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
35 documented issues across all years, most serious first.
Oil sludge and engine failure
- What you'll notice
- The oil pressure light flickers at idle or stays on, then knocking or rattling, stalling, or the engine shutting off and not restarting. Many failures happen between about 70,000 and 145,000 miles.
- Why it happens
- The 2.7L V6 is prone to oil breaking down into thick sludge that blocks oil flow, especially if oil changes are stretched out. Starved bearings and the timing chain then fail, sometimes breaking a connecting rod.
- What to do
- Change the oil every 3,000–5,000 miles with the correct oil, and check the level often. If the oil light flickers or you hear knocking, stop driving and have the engine checked. A sludged engine usually needs replacing.
Harsh, delayed or erratic shifting
- What you'll notice
- Hard clunks when downshifting at low speed, a delay before the car moves, getting stuck in a low gear until restarted, or a check engine light with transmission codes.
- Why it happens
- The automatic transmission in these Sebrings is known for shift problems from worn internal parts, solenoids and pressure sensors, or the transmission computer.
- What to do
- Have the codes read and the fluid checked; use only the Chrysler-specified fluid. Sometimes a sensor, solenoid or computer update fixes it, but some cars need a rebuild.
Automatic transmission failure
- What you'll notice
- Slipping, flaring revs between shifts, harsh shifts, or the car stuck in one gear or not moving.
- Why it happens
- The automatic transmission in this generation wears out, often around 90,000 miles.
- What to do
- Check the fluid level and condition. If it slips or will not move, get a transmission diagnosis before more damage is done.
Front lower ball joints can separate (recalls)
- What you'll notice
- Clunking from the front end, wandering steering, or uneven tire wear. In the worst case the wheel can fold under the car.
- Why it happens
- The rubber boots on the front lower ball joints can tear and let in water and dirt, so the joint wears or corrodes until it separates. Recalls 97V-201, 99V-066 and 00V-421 inspect and replace them.
- What to do
- Have a dealer check all three ball joint recalls by VIN, and have the front end inspected if you hear clunks.
Free at a Chrysler, Dodge, Jeep or Ram dealer if it was never done. Check your VIN.
Shifter can let the key come out when not in Park (recall)
- What you'll notice
- The key may come out of the ignition with the shifter not in Park, or the shifter feels loose.
- Why it happens
- A shifter cable adjustment problem can break a pin and defeat the park interlock. Recall 98V-183 replaces the shifter parts where needed.
- What to do
- Always set the parking brake. Have a dealer check the recall.
Free at a Chrysler, Dodge, Jeep or Ram dealer if it was never done. Check your VIN.
Throttle cable can fray and stick (recall)
- What you'll notice
- The gas pedal feels sticky or does not return fully, so the engine stays revved.
- Why it happens
- The throttle cable on cars with the 2.5L V6 can fray and bind. Recall 02V-186 replaces it.
- What to do
- If the pedal sticks, shift to Neutral, brake and pull over. Have the recall checked.
Free at a Chrysler, Dodge, Jeep or Ram dealer if it was never done. Check your VIN.
Brake booster vacuum hose installed wrong (recall)
- What you'll notice
- A hard brake pedal or longer stops.
- Why it happens
- On convertibles with the 2.5L V6, the vacuum hose for the power brake booster was installed incorrectly. Recall 96V-123 fixes it.
- What to do
- If the brake pedal feels hard, do not drive until it is checked. Have the recall done.
Free at a Chrysler, Dodge, Jeep or Ram dealer if it was never done. Check your VIN.
Crank sensor wiring can short and stall the engine (recall)
- What you'll notice
- The engine suddenly stalls while driving and may not restart right away.
- Why it happens
- The crankshaft sensor wiring could touch a new heat shield and short to ground. Recall 00V-299 reroutes it.
- What to do
- Have the recall checked. If it stalls in traffic, get safely off the road.
Free at a Chrysler, Dodge, Jeep or Ram dealer if it was never done. Check your VIN.
Transmission cooler hoses can leak (recall)
- What you'll notice
- Red fluid under the front of the car, smoke from the engine bay, or poor shifting.
- Why it happens
- The transmission cooler hoses can leak fluid onto hot parts. Recall 01V-011 replaces them.
- What to do
- Check for red fluid drips and have the recall done.
Free at a Chrysler, Dodge, Jeep or Ram dealer if it was never done. Check your VIN.
Sun visor can come loose when the airbag fires (recall)
- What you'll notice
- No warning sign before a crash.
- Why it happens
- The passenger sun visor can break free when the passenger airbag deploys and hit the occupant. Recalls 15V-338 and 16V-401 add a tether.
- What to do
- Have a dealer check both recalls by VIN.
Free at a Chrysler, Dodge, Jeep or Ram dealer if it was never done. Check your VIN.
Fuel return line can leak (recall)
- What you'll notice
- A fuel smell, fuel drips, or fuel wetness near the tank or lines.
- Why it happens
- A restricted fitting in the fuel return line can raise fuel pressure and make a hose leak (recall 03V-443). Some 2004 two-door cars also have a poorly molded return hose fitting that can break (recall 04V-313).
- What to do
- Do not drive with a fuel smell. Have a dealer check both recalls by VIN.
Free at a Chrysler, Dodge, Jeep or Ram dealer if it was never done. Check your VIN.
Right steering knuckle may crack (recall)
- What you'll notice
- Clunking from the right front, wandering steering, or the wheel looking out of line.
- Why it happens
- Some right steering knuckles were damaged during manufacturing and can crack and separate. Recall 04V-579 replaces it.
- What to do
- Have the recall checked by VIN. Any new front-end clunk should be inspected right away.
Free at a Chrysler, Dodge, Jeep or Ram dealer if it was never done. Check your VIN.
Engine stalls at stops or while driving
- What you'll notice
- The engine shuts off at a light, while braking, or while driving, while the lights and radio stay on. It often restarts.
- Why it happens
- No single cause has been confirmed. A recall (08V-152) covers a corroding tire pressure sensor connector that can cause stalling, but many owners report stalls where dealers find no code or cause.
- What to do
- Make sure all recalls are done. Write down when it happens (damp weather, braking, idle) to help a shop find it, and have the engine computer checked for updates.
Tire pressure sensor connector can short (recall)
- What you'll notice
- No-start, a dead battery, or stalling.
- Why it happens
- An unused tire pressure monitor connector can corrode and short out. Recall 08V-152 covers it.
- What to do
- Have a dealer check the VIN, especially if the car stalls or drains the battery.
Free at a Chrysler, Dodge, Jeep or Ram dealer if it was never done. Check your VIN.
Radiator fan connector can short and start a fire (recall)
- What you'll notice
- A burning smell or smoke from the front of the engine bay.
- Why it happens
- On cars with the 2.4L engine, coolant can be drawn into the left radiator fan motor connector and short it. Recall 07V-473 covers it.
- What to do
- Have the recall checked right away.
Free at a Chrysler, Dodge, Jeep or Ram dealer if it was never done. Check your VIN.
Seat position sensors for airbags may fail (recall)
- What you'll notice
- The airbag light may come on.
- Why it happens
- Front seat track position sensors, which tell the airbags how close you sit, may not work right. Recall 07V-240 covers it.
- What to do
- Have the recall checked; an airbag light means the system may not work right.
Free at a Chrysler, Dodge, Jeep or Ram dealer if it was never done. Check your VIN.
ABS software can lock the rear brakes (recall)
- What you'll notice
- The rear wheels lock up during hard braking, making the car slide.
- Why it happens
- The anti-lock brake computer software could lock the rear brakes in certain stops. Recall 06V-493 updates it.
- What to do
- Have the recall done by VIN.
Free at a Chrysler, Dodge, Jeep or Ram dealer if it was never done. Check your VIN.
Hood can open while driving (recall)
- What you'll notice
- The hood pops or flutters at speed.
- Why it happens
- The hood latch striker can break. Recall 06V-431 covers it.
- What to do
- Have the recall done; if the hood flutters, slow down and pull over.
Free at a Chrysler, Dodge, Jeep or Ram dealer if it was never done. Check your VIN.
Windshield defroster can stop working (recall)
- What you'll notice
- The defroster does not clear fog or frost from the windshield.
- Why it happens
- On cars with automatic climate control, the HVAC software could turn off the defrost function. Recall 06V-494 updates it.
- What to do
- Have the recall done before winter.
Free at a Chrysler, Dodge, Jeep or Ram dealer if it was never done. Check your VIN.
Fuel gauge reads higher than actual (recall)
- What you'll notice
- The car runs out of gas while the gauge still shows fuel.
- Why it happens
- On 2.4L cars, a software problem can make the gauge show more fuel than is in the tank. Recall 09V-047 updates it.
- What to do
- Use the trip odometer to track fuel until the recall is done.
Free at a Chrysler, Dodge, Jeep or Ram dealer if it was never done. Check your VIN.
Engine computer circuit board can crack and stall (recall)
- What you'll notice
- The engine stalls suddenly and may not restart.
- Why it happens
- A new adhesive in the engine computer can crack its circuit board. Recall 08V-528 covers it.
- What to do
- Have a dealer check the VIN.
Free at a Chrysler, Dodge, Jeep or Ram dealer if it was never done. Check your VIN.
Airbags and seat belt pretensioners may not deploy (recall)
- What you'll notice
- The airbag light may come on.
- Why it happens
- A short in the occupant restraint control module can stop the airbags and pretensioners from working in a crash. Recall 16V-668 covers it.
- What to do
- Have a dealer check the VIN.
Free at a Chrysler, Dodge, Jeep or Ram dealer if it was never done. Check your VIN.
Power steering hose can leak and start a fire (recall)
- What you'll notice
- Power steering fluid leaking, a burning smell, or whining steering.
- Why it happens
- The power steering pressure hose can separate at its crimp and spray fluid on hot parts. Recall 10V-475 covers it.
- What to do
- If you smell burning fluid, stop and have it checked. Have the recall done.
Free at a Chrysler, Dodge, Jeep or Ram dealer if it was never done. Check your VIN.
Brake booster clip may be missing (recall)
- What you'll notice
- No warning before the brakes suddenly do not respond.
- Why it happens
- The clip that holds the brake pedal to the brake booster rod may be missing or formed wrong. Recall 10V-009 covers it.
- What to do
- Have a dealer check the VIN right away.
Free at a Chrysler, Dodge, Jeep or Ram dealer if it was never done. Check your VIN.
Rusted front subframe
- What you'll notice
- Clunks from the front end, poor alignment, or a failed safety inspection for rust.
- Why it happens
- The front subframe can rust badly on high-mileage cars in salt-belt states.
- What to do
- Have the subframe inspected for rust at each service. A badly rotted subframe must be replaced before it fails.
Stalling or no-start from a failed distributor sensor
- What you'll notice
- The engine stalls without warning, often once warm, or cranks but will not start. It may restart after cooling down.
- Why it happens
- A sensor built into the distributor that tells the computer engine position fails, so the engine loses spark and fuel.
- What to do
- Have a shop check for spark and position-sensor codes when it acts up. Replacing the distributor or its sensor usually fixes it.
Failed emissions test
- What you'll notice
- The check engine light is on, or the car fails a state smog or emissions test.
- Why it happens
- Worn oxygen sensors, catalytic converters and related parts on high-mileage cars are the usual cause.
- What to do
- Have the codes read before the test so you know which part is causing the failure.
Rear spring seat cracks and clunks
- What you'll notice
- Clunking or squeaking from the rear over bumps, and in bad cases a loose rear strut.
- Why it happens
- The aluminum spring seat castings in the rear suspension can crack or corrode.
- What to do
- Have the rear struts and spring seats inspected. Replace cracked parts on both sides before the strut comes loose.
Heater blows cold
- What you'll notice
- Little or no heat from the vents, sometimes with the check engine light on.
- Why it happens
- A stuck-open thermostat keeps the engine from warming up and sets a code; low coolant or a clogged heater core also cuts heat.
- What to do
- Check the coolant level first, then have the thermostat and heater core checked.
Stalls when coming to a stop
- What you'll notice
- The engine dies as you slow down or stop at a light.
- Why it happens
- Dirty throttle bodies, idle control problems or sensor faults are typical causes on these cars.
- What to do
- Have the codes read and the throttle body cleaned. Get it fixed soon, since stalling in traffic is dangerous.
Horn goes off by itself
- What you'll notice
- The horn sounds on its own, sometimes for a long time while the car is parked and locked, often late at night.
- Why it happens
- The horn switch in the steering wheel pad or the clock spring behind it fails and shorts.
- What to do
- Pull the horn fuse or relay as a stopgap. The usual fix is replacing the steering wheel horn switch; a technician should handle it because it sits with the airbag.
Battery won't hold a charge
- What you'll notice
- The car won't start after sitting, or the battery dies repeatedly even after being replaced.
- Why it happens
- Owners report weak batteries and drains, sometimes linked to charging system or electrical faults.
- What to do
- Have the battery, alternator and any parasitic drain tested before buying another battery.
Brakes wear out early
- What you'll notice
- Grinding or squealing brakes, or pads and rotors needing replacement well before 40,000 miles.
- Why it happens
- Owners report brake pads and rotors wearing out early.
- What to do
- Have the brakes inspected at each oil change and replace pads before they reach the rotors.
Blower fan works only on high
- What you'll notice
- The heater and A/C fan only blows on the highest setting, or some speeds stop working.
- Why it happens
- The blower motor resistor, which sets the lower fan speeds, burns out.
- What to do
- Replace the blower motor resistor; it is a small, inexpensive part. If it keeps failing, have the blower motor checked too.
Paint peeling and bubbling
- What you'll notice
- Paint bubbles, peels or flakes off, often on the roof, hood and trunk.
- Why it happens
- The factory paint or clear coat lets go from the surface.
- What to do
- Ask a dealer about paint coverage, then get repaint quotes. Keep bare spots sealed to slow rust.
Repair prices for your Chrysler Sebring
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace engine with a used or remanufactured unit
- Replace transmission solenoid/sensor, or rebuild transmission
- Rebuild or replace automatic transmission
- Replace distributor or pickup sensor
- Replace oxygen sensor or catalytic converter
- Replace rear strut/spring assemblies and mounts
- Replace blower motor resistor
- Replace thermostat or flush heater core
- Clean throttle body or replace idle/sensor part
- Replace steering wheel horn switch or clock spring
- Diagnose stalling and repair wiring or sensor
- Repaint affected panels
- Test charging system and replace battery or alternator
- Replace front brake pads and rotors
- Replace front subframe
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Free dealer recall repairNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.