Dodge Viperproblems, repair costs and recalls
Problems reported across 1996–2017. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
32 documented issues across all years, most serious first.
Crankshaft damper bolt works loose
- What you'll notice
- A new vibration, a wobbling crank pulley at the front of the engine, or a drive belt that suddenly comes off.
- Why it happens
- The bolt holding the crankshaft damper (harmonic balancer) on the 8.0L V10 can loosen. Left alone, it can damage the crankshaft nose.
- What to do
- Stop driving if the pulley wobbles or the belt comes off. A shop can re-torque the bolt with thread locker; pinning kits are available to stop it from coming back.
Head gasket leaks on original gaskets
- What you'll notice
- Coolant or oil weeping down the sides of the block, overheating, or oil and coolant mixing.
- Why it happens
- The original composite head gaskets on these engines break down with age. Later replacement gaskets are multi-layer steel.
- What to do
- Look for staining on the block below the heads. If you see coolant loss or overheating, have a cooling system pressure test and combustion leak test done.
Steering rack mounting brackets can crack (recall)
- What you'll notice
- Steering feels loose, delayed or clunky, especially on cars driven hard or on track.
- Why it happens
- Hard driving and track use could crack the brackets that mount the steering rack to the frame. Eventually the rack could break free. Chrysler added reinforcement gussets.
- What to do
- Ask a dealer to check whether recall 01V313000 was done on your car. It's free.
Free at a Dodge/Chrysler dealer if the recall was never done.
Rear differential mounting bracket welds can crack (recall)
- What you'll notice
- Clunks from the rear under hard acceleration, or unstable handling.
- Why it happens
- On cars used for track or aggressive driving, the welds on the rear differential mounting bracket could crack and the bracket could come loose. Dealers reinforce the frame.
- What to do
- Have a dealer confirm recall 01V312000 was completed, especially if the car has been tracked.
Free at a Dodge/Chrysler dealer if the recall was never done.
Catalytic converter failure
- What you'll notice
- Check engine light, poor running, a rattle under the car, or a failed emissions test.
- Why it happens
- Some cars of this generation had catalytic converter problems. On 2003-2006 cars the converters are very expensive.
- What to do
- Have the codes read and the converters checked. Fix misfires first so new converters don't fail too.
Airbags can deploy on their own (recall)
- What you'll notice
- Front or side airbags or seat belt pretensioners could fire while driving with no crash. You may see the airbag warning light.
- Why it happens
- Electrical noise could damage a part in the airbag control module. Chrysler issued recalls 12V527/13V040 and then 15V046000 to replace the module and sensors.
- What to do
- Have a dealer check that all airbag control module recalls are complete. The repair is free.
Free at a Dodge/Chrysler dealer if the recall was never done.
Fuel pump wiring can chafe and stall the engine (recall)
- What you'll notice
- The engine suddenly stalls and won't restart because the fuel pump fuse blew.
- Why it happens
- The fuel pump wiring could rub on an underbody heat shield until it shorted.
- What to do
- Ask a dealer to confirm recall 03V292000 was done. They wrap the harness and cover the shield edge.
Free at a Dodge/Chrysler dealer if the recall was never done.
Restraint control module can fire airbags unexpectedly (recall)
- What you'll notice
- The airbags or seat belt pretensioners could deploy without a crash.
- Why it happens
- A fault in the occupant restraint control module could trigger them. Chrysler replaces the module.
- What to do
- Ask a dealer to confirm recall 19V885000 was completed.
Free at a Dodge/Chrysler dealer if the recall was never done.
Early engine failure
- What you'll notice
- Knocking from the engine, low oil pressure, or the engine failing, sometimes at low miles.
- Why it happens
- Some earlier cars of this generation lost engines, often under warranty, possibly from rod bearing failure or debris left from manufacturing. It is considered rare.
- What to do
- Ask whether the engine has been replaced and check the warranty history. Shut the engine off right away if it knocks or the oil light comes on.
Passenger airbag door can break loose (recall)
- What you'll notice
- No symptoms. In a crash the passenger airbag door could detach.
- Why it happens
- A bad weld on the passenger airbag chute on cars built in early January 2016. Dealers replace the upper dash panel.
- What to do
- Ask a dealer to check recall 16V750000.
Free at a Dodge/Chrysler dealer if the recall was never done.
Driver airbag wiring can be pinched (recall)
- What you'll notice
- The airbag warning light may come on. The driver airbag may not deploy correctly.
- Why it happens
- Wiring for the driver airbag could be pinched on some 2016 cars. Dealers replace the airbag and clockspring.
- What to do
- Ask a dealer to check recall 16V736000.
Free at a Dodge/Chrysler dealer if the recall was never done.
Clutch slipping or wearing out
- What you'll notice
- Engine revs climb without the car speeding up, especially under hard acceleration, a burning smell after hard driving, or the engagement point moving around in the pedal travel.
- Why it happens
- The V10's huge torque is hard on the clutch, and hard launches and track use wear the friction disc and pressure plate. Used buyers are told to assume a clutch may be due unless records prove otherwise.
- What to do
- If it slips or smells burnt, ease off and have it inspected before the flywheel is damaged. Ask for clutch records when buying.
Clutch slave cylinder seal failure
- What you'll notice
- The clutch pedal feels spongy or sinks, gears grind or are hard to select, or there is fluid near the bellhousing.
- Why it happens
- The clutch slave cylinder design on 1992-2002 Vipers is prone to seal leaks, letting fluid out and air in, so the clutch doesn't fully release.
- What to do
- Check the clutch fluid reservoir. A leaking slave cylinder is usually replaced along with the clutch since the transmission must come out.
Soft clutch pedal from leaking slave cylinder
- What you'll notice
- The clutch pedal feels soft or is slow to come back up, and you may see a few drops of clear fluid under the transmission.
- Why it happens
- The slave cylinder inside the transmission bellhousing can leak. If ignored, the clutch can stop working entirely.
- What to do
- Get it looked at early, while the car still drives. Have a Viper-experienced shop or dealer confirm the leak source.
Power steering pump bracket cracks and assist is lost
- What you'll notice
- Steering suddenly becomes heavy, often with a squeal or a belt that has come off.
- Why it happens
- The cast bracket that holds the power steering pump can crack, and the factory pulley can also fail, letting the belt come off.
- What to do
- Pull over safely and check the belt. Replace a cracked bracket; stronger billet brackets and pulleys are sold as upgrades.
Optional racing harness may not be strong enough (recall)
- What you'll notice
- No symptoms. Applies to ACR and GT2 cars with the optional 5-point racing harness.
- Why it happens
- The harness might not meet the voluntary FIA load specifications. Chrysler replaced it.
- What to do
- If your car has the factory racing harness, ask a dealer to check recall 01V120000.
Free at a Dodge/Chrysler dealer if the recall was never done.
Heat soak and damage around the side-exhaust sills
- What you'll notice
- Lots of heat in the cabin and door sills, plus scraped, burnt or rusted paint on the rocker panels around the side exhaust covers.
- Why it happens
- The V10 and side-exit exhaust run very hot right next to the cabin, and the low rocker panels get scraped. Replacement panels are costly.
- What to do
- Inspect the rocker and exhaust cover area when buying. Many owners repaint or coat these panels early to protect them.
Window regulator failure
- What you'll notice
- A window is slow, noisy, grinds, or won't go up or down.
- Why it happens
- Most cars of this era used weak window regulators that break internally. An upgraded regulator became available from 2009.
- What to do
- Replace the regulator, ideally with the upgraded part.
Window drops wrong and hits the roof when the door closes
- What you'll notice
- When you shut the door, the glass slams into the roof or top instead of tucking in, which can break the glass or damage the body.
- Why it happens
- The windows drop slightly when a door opens. If the module that controls that loses its settings, such as after a dead battery, the glass is no longer lowered.
- What to do
- After a battery has gone dead, check that the windows drop before shutting the doors. Have the window positions re-learned.
Convertible top and seal leaks
- What you'll notice
- Water inside the car after rain, damp carpets, or dry, brittle leather.
- Why it happens
- The soft top fabric and the weather seals wear, tear or go missing with age.
- What to do
- Check the top and seals carefully and replace damaged seals before water damages the interior.
Oil leak from the front timing cover
- What you'll notice
- Oil wetness on the front of the engine and drips under the front of the car.
- Why it happens
- The front timing cover is called out as the spot to check most for leaks on these V10s.
- What to do
- Have the leak confirmed and the front cover resealed before it gets onto the belts.
Headlights or dash lights flicker or fail (recall)
- What you'll notice
- The parking lights, headlights or instrument lights flicker or go out.
- Why it happens
- The park lamp contacts in the multifunction switch could corrode. Dealers reflash the body control module software.
- What to do
- Have a dealer check recall 03V388000.
Free at a Dodge/Chrysler dealer if the recall was never done.
High oil consumption
- What you'll notice
- The oil level drops between changes and you need to add oil often.
- Why it happens
- Some 2013-2015 cars used too much oil, and Chrysler worked with owners to find and fix affected engines. The dipstick is also hard to read accurately.
- What to do
- Check the oil on level ground after the car has sat, reading the stick right away. Report heavy oil use to a dealer.
Water pump failure
- What you'll notice
- Coolant leaks from the front of the engine, a sweet smell, or the temperature gauge climbing.
- Why it happens
- The water pump on the last-generation Viper is reported to be prone to failure.
- What to do
- Watch for coolant drips and check the level often. Replace a leaking pump before the engine overheats.
Seat position sensor can make airbags deploy too softly (recall)
- What you'll notice
- No symptoms. The airbags may inflate with less force than intended in a crash.
- Why it happens
- The seat position sensors could misread where the seat is. Dealers add a metal shim to fix the reading.
- What to do
- Have a dealer check recall 14V529000.
Free at a Dodge/Chrysler dealer if the recall was never done.
Radio software could be hacked remotely (recall)
- What you'll notice
- No symptoms.
- Why it happens
- Security gaps in the Uconnect radio software could let outsiders reach some vehicle systems. Chrysler sent out a software update.
- What to do
- Make sure the radio software update from recall 15V461000 was installed.
Free at a Dodge/Chrysler dealer if the recall was never done.
Erratic or hunting idle
- What you'll notice
- The idle speed surges up and down or the engine nearly stalls at a stop.
- Why it happens
- A partly clogged idle control valve is the usual cause on these cars.
- What to do
- Have the idle control valve and throttle body cleaned or checked. It is usually a simple repair.
Oil and fluid leaks from aging gaskets and hoses
- What you'll notice
- Oil spots under the car, a burning oil smell, or damp gaskets around the engine.
- Why it happens
- Early Vipers are known for gasket leaks, and the hoses, belts and seals on these older cars are now aging out.
- What to do
- Have the leaks traced and replace hardened hoses and belts by age, not just mileage.
Clunk or click from the rear driveline
- What you'll notice
- A clunk when getting on and off the throttle, or a single click or pop from the rear as the clutch is released.
- Why it happens
- RepairPal lists these as the most commonly reported Viper complaints. Some driveline clunk is considered normal on this car.
- What to do
- If the noise is new or getting louder, have the U-joints, differential and mounts checked.
Door hinges sag
- What you'll notice
- The door rides low, rubs or catches on closing, pops, or the weather seal is damaged and leaks water.
- Why it happens
- The door hinges on these cars can sag or deform over time.
- What to do
- Lift the open door gently to check for play. Have worn hinges adjusted or replaced before seals and paint are damaged.
Battery runs down when the car sits
- What you'll notice
- The car won't start or cranks slowly after sitting for a couple of weeks.
- Why it happens
- Vipers are often stored for long stretches, and the battery drains. A dead battery can also cause other problems like lost window settings.
- What to do
- Use a trickle charger or battery maintainer when the car is stored.
Windows bind or hit the body
- What you'll notice
- A window is noisy or binds, or the glass touches the body when the door closes.
- Why it happens
- Window operation and door fit are known weak points carried over from earlier Vipers.
- What to do
- Run both windows fully up and down and close the doors slowly to check. Have the glass and door adjusted.
Repair prices for your Dodge Viper
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace clutch kit (OEM)
- Replace slave cylinder with clutch kit
- Replace head gaskets (multi-layer steel)
- Replace power steering pump and bracket
- Replace worn U-joint
- Replace catalytic converter
- Replace window regulator
- Replace window regulator if damaged
- Replace leaking weatherstrip or soft top cover
- Reseal engine front cover
- Replace battery
- Replace water pump
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Install steering rack reinforcement kit (recall 01V313000)No charge if your vehicle is included
- Inspect and reinforce differential bracket (recall 01V312000)No charge if your vehicle is included
- Replace racing harness (recall 01V120000)No charge if your vehicle is included
- Replace airbag control module and sensors (recalls 13V040000 / 15V046000)No charge if your vehicle is included
- Wrap fuel pump harness and cover heat shield (recall 03V292000)No charge if your vehicle is included
- Reflash body control module (recall 03V388000)No charge if your vehicle is included
- Replace occupant restraint control module (recall 19V885000)No charge if your vehicle is included
- Install seat position sensor shim (recall 14V529000)No charge if your vehicle is included
- Radio software update (recall 15V461000)No charge if your vehicle is included
- Replace passenger upper dash panel (recall 16V750000)No charge if your vehicle is included
- Replace driver airbag and clockspring (recall 16V736000)No charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.