GMC Yukonproblems, repair costs and recalls
Problems reported across 1996–2026. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
42 documented issues across all years, most serious first.
Four-speed automatic slipping
- What you'll notice
- Engine revs climb without acceleration, a gear goes missing, or reverse fails.
- Why it happens
- The 4L60-E's 3-4 clutch pack is a known weak spot, especially in heavy SUVs that tow.
- What to do
- Get a fluid check and road test soon. Stop towing until it is diagnosed.
Lifter failure on V8s with cylinder deactivation
- What you'll notice
- Tapping noise, misfire codes, shaking at idle, or power loss.
- Why it happens
- The deactivating lifters can stick or collapse, sometimes ruining the camshaft.
- What to do
- Diagnose quickly to limit engine damage.
Brake assist loss recall
- What you'll notice
- The brake pedal feels hard and the SUV takes longer to stop. A brake warning may appear.
- Why it happens
- The engine-driven vacuum pump that powers the brake booster can lose output. GM recalled affected V8 models.
- What to do
- Check your VIN for open recalls and have the fix done. A hard pedal deserves immediate attention.
6.2L engine recall for rod and crank defects
- What you'll notice
- Engine knock, low oil pressure, rough running, or a sudden stall.
- Why it happens
- Some engines had defective crankshaft or connecting rod parts that can fail.
- What to do
- Check for open recalls. Stop driving if you hear knocking.
Heated windshield washer module can short and catch fire (recall)
- What you'll notice
- On trucks built with the heated washer fluid option, you may notice a burning smell or smoke from under the hood, or other electrical features acting up. Many owners never see a warning before the module overheats.
- Why it happens
- The small heater that warms the washer fluid can short-circuit internally and overheat. GM recalled it twice and ended up disabling and removing the heater altogether.
- What to do
- Ask the dealer to check the VIN for open recalls right away. If the recall is still open, book the free dealer repair now and park outside until it is done. Stop driving and have it towed if you smell burning or see smoke.
Ten-speed transmission valve can lock the rear wheels (recall)
- What you'll notice
- A sudden harsh downshift or a brief lockup of the rear wheels while driving, sometimes after a warning message about the transmission. Some owners first notice a rough shift into a lower gear.
- Why it happens
- A control valve inside the ten-speed automatic can wear and lose pressure, which can cause an abrupt downshift that momentarily locks the rear wheels. The 2021 recall covers trucks with the 3.0L diesel, and a later recall covers 2022 trucks. Dealers load software that watches for the fault and limits the transmission before it can lock up.
- What to do
- Check your VIN for open recalls and get the free software update done promptly. If you feel a harsh downshift or the rear wheels grab, slow down, pull over safely and have the truck towed to a dealer.
Accelerator cable can snag and hold the throttle open (recall)
- What you'll notice
- The pedal feels sticky, or it does not spring all the way back when you lift your foot.
- Why it happens
- On these trucks the throttle cable could rub where it passes the dash and floor covering, so the throttle may not close fully.
- What to do
- Treat a sticking pedal as an emergency: stop driving and have the cable routing inspected. Ask the dealer to check the VIN for the free repair.
Front brake rotor can crack (recall)
- What you'll notice
- Grinding or knocking from a front wheel, a pedal that pulses, or a wheel that feels loose.
- Why it happens
- A batch of front rotors was built out of specification and can crack in service; in the worst case the wheel can come away.
- What to do
- Stop driving it and have the front brakes inspected now. The recall repair is free, so check the VIN first.
Steering shaft pinch bolt can loosen and fall out (recall)
- What you'll notice
- Vague or sloppy steering, a clunk when you turn, or in the worst case no steering response at all.
- Why it happens
- The bolt that clamps the steering shaft coupling was not always tightened properly and can work its way out.
- What to do
- Do not drive it until the coupling has been checked. Run the VIN for the free recall repair.
ABS can grab on its own at low speed (recall)
- What you'll notice
- At walking pace the pedal drops away, the brakes pulse, or the truck takes much longer to stop than you expect.
- Why it happens
- Corrosion from road salt reaches the wheel speed sensor circuit, and the ABS reads it as a locked wheel and releases pressure it should be holding.
- What to do
- Have the brakes and sensors checked right away, especially if you live where roads are salted. Check the VIN for the recall.
Missing body plugs can let exhaust fumes into the cabin (recall)
- What you'll notice
- An exhaust smell inside, worst with the tailgate or a window open, sometimes with headaches or drowsiness on longer drives.
- Why it happens
- Plugs were left out of the wheelhouse panels, leaving a path for exhaust gas to reach the interior.
- What to do
- Drive with the windows open and get it inspected immediately; exhaust in the cabin can make you pass out. The recall repair is free.
Brake pipe can rub the body and leak fluid (recall)
- What you'll notice
- A long or sinking pedal, a brake warning light, or wet spots under the truck.
- Why it happens
- A brake pipe can touch the body where it was routed, and the rubbing wears through the line.
- What to do
- Stop driving if the pedal has changed at all and have it towed in. Check the VIN for the free recall repair.
Hydro-boost brake assist seal can split (recall)
- What you'll notice
- The pedal suddenly needs much more effort, and the truck takes far longer to stop.
- Why it happens
- A seal in the hydraulic brake booster relief valve can fracture, so the booster stops multiplying your pedal effort.
- What to do
- Stop driving if the pedal has gone hard and have it towed. The recall fix is free, so check the VIN first.
Brake pedal pushrod retainer can be missing (recall)
- What you'll notice
- The pedal may feel loose or disconnect from the brakes completely.
- Why it happens
- A retainer that holds the pedal pushrod to the booster was left off during assembly, so the connection can separate.
- What to do
- Do not drive it; have it towed and the pedal linkage checked under the free recall.
Power steering hose can split at full lock (recall)
- What you'll notice
- A groan or whine when turning, heavy steering, and red fluid under the front of the truck.
- Why it happens
- Holding the wheel at full lock spikes pressure in a hose that was not strong enough, and it can fracture.
- What to do
- Get it inspected right away: fluid on a hot engine can start a fire and the steering gets very heavy. The recall repair is free.
Ignition lock can bind and snap back out of Run (recall)
- What you'll notice
- The key is hard to turn, or the ignition jumps back from Run to Accessory and the engine dies.
- Why it happens
- The ignition lock cylinder can bind so that the key does not stay where you put it, cutting engine, power steering and airbag power.
- What to do
- Take everything heavy off the key ring and have it fixed under the recall right away; losing power steering at speed is dangerous.
Contaminated control module can short and stall the truck (recall)
- What you'll notice
- The engine cuts out while driving, warning lights come on together, or electrical features act strangely.
- Why it happens
- Contamination inside a control module can create a short circuit that shuts the engine down without warning.
- What to do
- Have the VIN checked and the module replaced under the recall before driving it far; a stall in traffic is a safety risk.
Park lock can fail and let the truck roll (recall)
- What you'll notice
- The truck creeps or rolls after you shift to Park and let go of the brake.
- Why it happens
- The park mechanism may not engage fully, so nothing holds the driveline when the shifter says Park.
- What to do
- Always set the parking brake, and have it repaired under the recall now; a rollaway can hurt someone.
Wheel speed sensor fault can brake one wheel by itself (recall)
- What you'll notice
- The truck pulls hard to one side under braking or tugs at the wheel on its own, usually with ABS or stability warnings.
- Why it happens
- If a wheel speed sensor fails, the stability system can misread it and apply the brake at one wheel without the driver asking.
- What to do
- Have the recall software update done as soon as you can and get any ABS warning diagnosed; this can cause a loss of control.
Fuel pump assembly can leak from a missing regulator (recall)
- What you'll notice
- A strong fuel smell, wet fuel around the tank area, or hard starting and stalling.
- Why it happens
- Some fuel pump modules were built without a pressure regulator, so the system can run over pressure and leak.
- What to do
- Park it outside, away from buildings, and have it towed for the free recall repair; leaking fuel is a fire risk.
Rear control arm bolts can break (recall)
- What you'll notice
- Clunking or banging from the rear over bumps, a rear wheel that looks out of line, or wandering at speed.
- Why it happens
- Outer rear control arm bolts can fracture, which lets the wheel move out of position.
- What to do
- Stop driving and have it inspected under the recall; a broken link can cause a loss of control.
Wrong diesel fuel tank can leak in a rollover (recall)
- What you'll notice
- Nothing in normal driving; the tank only matters in a crash or rollover.
- Why it happens
- Some diesel trucks were built with a fuel tank that does not meet the rollover leak requirement.
- What to do
- Run the VIN and have the tank replaced under the recall at no cost.
Wrong front hub bolts can loosen (recall)
- What you'll notice
- Clicking or clunking from a front wheel, vibration that gets worse with speed, or a wheel that feels loose.
- Why it happens
- Trucks built with certain large wheels got the wrong front hub bolts, which can stretch or work loose.
- What to do
- Stop driving and have the front hubs inspected under the recall; a loose hub can cause a loss of control.
Missing transfer case part can lock the wheels (do-not-drive recall)
- What you'll notice
- Sudden grinding or binding from under the truck, or the wheels locking up with no warning.
- Why it happens
- A component can be missing inside the transfer case, which lets it jam and lock the front or rear wheels.
- What to do
- Do not drive it. Check the VIN and have it towed to the dealer for the free repair.
Transfer case can lock the wheels without warning (do-not-drive recall)
- What you'll notice
- Grinding or binding from the driveline, or wheels that suddenly stop turning freely.
- Why it happens
- On certain four-wheel-drive and all-wheel-drive trucks a part can be missing from the transfer case, letting it seize.
- What to do
- Do not drive it. Run the VIN and arrange a tow to the dealer for the free repair.
Fuel injector "spider" assembly problems
- What you'll notice
- Slow starts, rough idle, misfires, or a fuel smell.
- Why it happens
- The central injector unit's nozzles can gum up or leak as the truck ages.
- What to do
- Have a shop test it. Treat any fuel smell as urgent.
Excess oil consumption
- What you'll notice
- Frequent oil top-offs, low-oil message, blue smoke on startup, misfires.
- Why it happens
- Oil passes the piston rings and burns, a problem tied to this engine family and its cylinder deactivation.
- What to do
- Watch the dipstick closely and ask a GMC dealer for an oil consumption test.
A/C stops cooling from a cracked condenser
- What you'll notice
- The air conditioning slowly gets weaker and then blows warm, often within the first few years. A shop may find the refrigerant charge is low or empty with no obvious damage.
- Why it happens
- The A/C condenser at the front of the truck, which is built together with a transmission cooler, can crack from repeated heating and cooling and let the refrigerant escape. GM extended coverage on this part for a limited time on certain trucks.
- What to do
- Have a shop check the system with leak dye or a sniffer before paying for a simple recharge, since a recharge alone will leak out again. Ask a GMC dealer whether special coverage 17336 ever applied to your VIN.
Eight-speed automatic shudder at steady speed
- What you'll notice
- A vibration that feels like driving over rumble strips, usually under light throttle at steady road speeds. It can come and go and may be joined by harsh or clunky shifts.
- Why it happens
- The original transmission fluid in the eight-speed automatic used with the 6.2L engine in these years can take on moisture, which makes the torque converter clutch grab and release unevenly. GM issued a bulletin calling for a full exchange to a revised fluid.
- What to do
- Ask a dealer or transmission shop about the fluid exchange in GM bulletin 18-NA-355. Get it done soon, because long-term shudder can wear out the torque converter.
Wipers can stop from cracked circuit board solder joints (recall)
- What you'll notice
- Wipers quit altogether, stick on one speed, or sweep only now and then.
- Why it happens
- Solder joints on the wiper control board crack after years of heat cycles and vibration, breaking the circuit.
- What to do
- Have it fixed before you have to drive in rain or snow, and check the VIN for the open recall.
Front passenger belt falls short of a federal restraint standard (recall)
- What you'll notice
- Nothing you can feel day to day; the belt looks and works normally.
- Why it happens
- The passenger restraint as built did not meet the federal requirement for how far the belt lets the head and neck travel in a crash.
- What to do
- Check the VIN for the open recall and have the free correction done; keep using the belt in the meantime.
Rear center belt can ride up onto the stomach (recall)
- What you'll notice
- The rear center lap belt sits high across the belly instead of low on the hips.
- Why it happens
- The belt routing lets the lap portion slide up out of position, which can cause internal injuries in a crash.
- What to do
- Have the free recall correction done and avoid seating a child in the rear center position until then.
Rear door hinge welds may be out of specification (recall)
- What you'll notice
- Nothing shows up in normal use; the door opens and closes as usual.
- Why it happens
- Welds on a rear door hinge were not made to specification, which weakens the door in a side impact.
- What to do
- Check the VIN and have the hinge inspected under the recall at no cost.
Third-row seat belt buckle rivet may be formed wrong (recall)
- What you'll notice
- Nothing obvious; the buckle latches and releases normally.
- Why it happens
- A rivet in the third-row buckle may not have been formed correctly, so the buckle may not hold in a crash.
- What to do
- Have the buckle inspected under the recall at no cost and seat passengers elsewhere until then.
No warning light if brake fluid runs low (recall)
- What you'll notice
- The brake warning light never comes on, even when the reservoir is low.
- Why it happens
- The instrument cluster software does not light the required warning for low brake fluid, so a slow leak can go unnoticed.
- What to do
- Get the free software update and check the fluid level yourself in the meantime.
Intake manifold gaskets leak coolant on the 5.7L V8
- What you'll notice
- Coolant level keeps dropping with no puddle, crusty residue on top of the engine, a sweet smell through the vents, or oil that looks like coffee with milk.
- Why it happens
- The intake gaskets used on this Vortec V8 soften and let coolant escape, sometimes outward and sometimes down into the oil.
- What to do
- Have the cooling system pressure-tested soon. If the oil looks milky, stop driving it until the gaskets are replaced, or the bearings will suffer.
Dashboard pad cracking
- What you'll notice
- Cracks appear across the top of the dash.
- Why it happens
- Sun and heat break down the dash surface over time.
- What to do
- Cosmetic. A dash cover helps. Keep cracks away from the air bag area in mind.
Magnetic Ride Control shocks leak or knock
- What you'll notice
- On trucks with the Magnetic Ride Control suspension (standard on Denali), you may see oily fluid on a shock body, hear knocking over bumps, or notice a bouncier ride or a suspension service message.
- Why it happens
- The electronically controlled shocks can develop seal leaks or internal noise as they age. GM has a service bulletin telling dealers how to judge a leak and to replace only the shock that has failed.
- What to do
- Have the shocks looked at during your next service. A light film is normal, but fluid running down the shock or a clear change in ride means that shock should be replaced.
Head restraint gap can pinch fingers (recall)
- What you'll notice
- A gap in the seat head restraint where fingers can be caught while adjusting it.
- Why it happens
- The head restraint design leaves a pinch point between moving parts.
- What to do
- Keep children's hands clear while adjusting the seats and have the free recall correction done when convenient.
Tire and loading label shows the wrong capacity (recall)
- What you'll notice
- The sticker in the door jamb lists a load and tire figure that does not match the truck.
- Why it happens
- The wrong label was applied at the factory, so owners may load the truck beyond what it is rated for.
- What to do
- Ask the dealer for the corrected label under the recall and go by the owner's manual until then.
Daytime running lights can stay on with the headlights (recall)
- What you'll notice
- The daytime running lights do not dim or switch off when you put the headlights on, and other drivers flash you.
- Why it happens
- The lighting software does not turn the running lights off as the federal standard requires.
- What to do
- Ask for the free software update at your next service visit.
Radio may be missing the electronic owner's manual (recall)
- What you'll notice
- The owner information pages in the radio menu are blank or missing.
- Why it happens
- The radio did not download the electronic owner's manual, which carries required safety information.
- What to do
- Ask the dealer to load the manual at no charge, or use the printed manual in the meantime.
Repair prices for your GMC Yukon
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Replace spider fuel injector assembly and intake gaskets
- Replace with remanufactured 4L60-E transmission
- Replace pistons and rings and AFM oil shield
- Replace lifters, camshaft and lifter guides
- Replace brake vacuum pump
- Replace engine under recall
- Disable and remove heated washer module
- Replace A/C condenser, evacuate and recharge
- Transmission fluid exchange to revised fluid
- Replace one Magnetic Ride Control shock
- Update transmission control software
- Inspect and reroute or replace accelerator cable
- Replace wiper control circuit board or module
- Replace front brake rotors in pairs
- Inspect and replace steering shaft pinch bolt
- Replace front passenger seat belt assembly
- Replace front wheel speed sensor and update ABS module
- Install missing wheelhouse and body plugs
- Replace brake pipe and bleed brakes
- Install head restraint pinch-point correction
- Replace hydro-boost unit and bleed brakes
- Replace rear center seat belt assembly
- Inspect rear door hinge welds and repair as needed
- Install brake pedal pushrod retainer clip
- Replace power steering pressure hose and flush system
- Install corrected tire and loading information label
- Replace ignition lock cylinder and relearn key
- Replace affected control module and reprogram
- Repair or replace transmission park lock components
- Replace wheel speed sensor and reprogram brake module
- Replace in-tank fuel pump module
- Reprogram body control module lighting software
- Replace third-row seat belt buckle assembly
- Replace rear outer control arm bolts and align
- Reprogram instrument cluster software
- Replace diesel fuel tank
- Replace front wheel hub bolts and torque to spec
- Inspect transfer case and install missing component
- Download electronic owner's manual to radio
- Replace intake manifold gaskets
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.