Hummer H2problems, repair costs and recalls
Problems reported across 2003–2009. Pick your model year below to see what applies to your vehicle.
Pick your engine to hide problems that only affect other engines. Not sure? It is on the sticker under the hood or in the owner's manual.
Ownership snapshot
Averages, not quotesRoutine maintenance costs (model-wide, not specific to one year or engine)
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
Ask for an estimate
The problems here are the ones we've documented so far, not a complete list or a reliability rating. Ask your shop for a written total that covers the work on your engine and trim, including any diagnostic fees, taxes and shop supplies.
Known problems
31 documented issues across all years, most serious first.
Wipers turn on by themselves or stop working
- What you'll notice
- The windshield wipers run on their own, will not shut off, work only now and then, or stop in the rain. The washer pump may also keep spraying until the reservoir is empty.
- Why it happens
- Water gets into the wiper motor and its control module at the base of the windshield, which corrupts the module. GM recalled some 2003 trucks for this, but owners of other years report the same thing.
- What to do
- Do not drive in rain or snow with wipers that may quit. Pulling the wiper fuse stops a runaway wiper temporarily. Ask a dealer whether your VIN is covered by a recall, then replace the wiper motor/module if not.
Windshield wiper motor can fail (recall)
- What you'll notice
- Wipers that work only sometimes or stop working, reducing your view in bad weather.
- Why it happens
- On some 2003 H2s, water could enter the wiper motor module, and an earlier campaign covered wiper motors that were built incorrectly. GM recalled the affected trucks.
- What to do
- Have a Hummer/GM dealer run your VIN for open recalls. The fix (a module cover or new motor) is free.
Blower motor wiring or resistor overheats
- What you'll notice
- A burning electrical smell, the fan working only on some speeds or cutting out, and in some reports melted plastic or smoke near the glove box.
- Why it happens
- The blower motor resistor and its wiring connector carry a lot of current and can overheat. Owners report melted connectors and harnesses on many H2 model years.
- What to do
- Turn the fan off and get it checked if you smell burning plastic. The resistor and its connector or pigtail should be replaced together.
Rusted brake lines burst (pedal sinks to the floor)
- What you'll notice
- The brake pedal suddenly goes soft or sinks to the floor, brake fluid leaks under the truck, or the brake warning light comes on.
- Why it happens
- The steel brake lines that run under the truck rust, especially where roads are salted, and eventually burst. Owners report sudden loss of braking with little warning.
- What to do
- If the pedal goes soft, stop driving and have the truck towed. On older H2s, have the brake lines inspected for heavy rust and replace them before they fail.
Hydro-boost brake accumulator can crack (recall)
- What you'll notice
- A heavier brake pedal and harder steering, or power steering fluid leaking near the brake booster.
- Why it happens
- The H2 uses the power steering pump to power its brakes (hydro-boost). The pressure reservoir on certain Bosch units can crack and come apart, letting fluid out and reducing brake and steering assist. GM recalled affected trucks.
- What to do
- Check your VIN for open recalls. If the brakes or steering suddenly feel heavy, stop safely and have it towed.
Heated washer fluid system fire risk (recall)
- What you'll notice
- Washer fluid heater problems, an electrical burning smell, smoke from under the hood, or other electrical faults.
- Why it happens
- The heated windshield washer system had a circuit board and ground wire that could short and overheat. GM issued recalls, first adding a fused harness and later disabling the module, because it could start a fire.
- What to do
- Make sure the heated washer recalls are done on your VIN. Until then, stop using the heated washer feature and have it checked if you smell burning.
Front ball joint or steering knuckle failure
- What you'll notice
- Clunking from the front end, wandering steering, uneven tire wear, and in the worst cases a front wheel that collapses or comes off the truck.
- Why it happens
- The heavy H2 and its big tires put high loads on the front ball joints and steering knuckles. Owners report ball joints snapping and front wheels separating, sometimes at speed.
- What to do
- Have the ball joints and knuckles checked at every tire rotation, especially on lifted trucks or those with larger tires. Replace worn joints right away.
Airbag light on (airbag module or water damage)
- What you'll notice
- The airbag warning light comes on and stays on, sometimes with a service message or other modules acting up.
- Why it happens
- The airbag control module (SDM) can fail, and some owners trace it to rain water leaking into the cabin near the module.
- What to do
- The airbags may not work while the light is on. Have the codes read, fix any water leak first, then repair or replace the module.
Automatic transmission slipping or stuck in gear
- What you'll notice
- Slipping between 1st and 2nd, flaring engine revs, delayed engagement, or the transmission sticking in one gear.
- Why it happens
- The heavy-duty 4-speed automatic behind the 6.0L works hard moving a 6,400-pound truck, and its clutches wear out. Owners report slipping and stuck-in-gear problems.
- What to do
- Check the transmission fluid level and smell. Have it diagnosed before it gets worse; frequent towing or big tires make wear faster.
Six-speed automatic shifts harshly or loses drive
- What you'll notice
- Harsh or erratic shifts, a transmission warning code, or the truck suddenly losing power to the wheels when pulling away.
- Why it happens
- The 6-speed automatic used with the 6.2L engine can develop internal faults; owners report early failures and transmission codes.
- What to do
- Have the codes read and the fluid checked as soon as shifts change. A software update or valve body repair sometimes helps; a failed unit needs a rebuild.
Frame and subframe rust
- What you'll notice
- Clicking when turning the steering wheel, heavy rust on the frame and underbody, or rusted-through brackets.
- Why it happens
- Road salt corrodes the H2’s frame and steel underbody parts. A dealer traced one owner’s clicking to a rusted subframe support.
- What to do
- Have the frame inspected, especially on trucks from snowy states. Treat rust early with an undercoating; severe rust needs welding repair.
Fuel pump flow control module failure
- What you'll notice
- Hard starting, stalling or loss of power, with fuel system codes.
- Why it happens
- The module that controls fuel pump speed on these trucks can fail. One owner was told their VIN was not included in a related recall.
- What to do
- Ask a dealer whether any recall or warranty extension covers your VIN, then have the fuel pump control module tested.
Low oil pressure or failing lifters
- What you'll notice
- Low oil pressure warning, a ticking or tapping from the engine, or the gauge reading lower than normal.
- Why it happens
- Owners report collapsed or failed valve lifters and low oil pressure on high-mileage 6.0L engines.
- What to do
- Stop driving if the oil pressure light comes on. Check the oil level, then have a shop test oil pressure before more damage occurs.
Broken exhaust manifold bolts (ticking exhaust leak)
- What you'll notice
- A ticking or tapping noise from the engine bay that is loudest on a cold start, sometimes an exhaust smell inside or around the truck, and in some cases a check engine light.
- Why it happens
- The bolts holding the cast-iron exhaust manifolds to the 6.0L cylinder heads snap after years of heating and cooling. Once a bolt breaks, exhaust leaks past the gasket. Owners have reported this on many H2s, sometimes with damage to nearby parts.
- What to do
- Have the manifold area checked for broken bolts. A leak near the cabin can let exhaust fumes in, so do not ignore a strong exhaust smell. Broken bolts usually have to be drilled out, so pick a shop that has done this job before.
Speedometer and gauges stick or stop working
- What you'll notice
- The speedometer, tachometer or other gauges freeze, jump around, drop to zero at speed or stop working entirely. Warning lights may come on together or the cluster backlighting may fail.
- Why it happens
- Components inside the instrument cluster fail with age, especially the small motors that move the needles. Owners report it at many mileages on these years.
- What to do
- Use a phone GPS app to check your speed until it is fixed. A cluster rebuild service is usually much cheaper than a new dealer cluster, which also needs programming.
Air blows from the wrong vents or will not cool
- What you'll notice
- Air only comes out of the defrost vents, the A/C blows warm air, or you cannot change where the air comes out. You may hear a clicking behind the dash.
- Why it happens
- An electric mode or blend door actuator behind the dashboard fails. It is the small motor that moves the flaps that send air to each vent or mix hot and cold.
- What to do
- Have the HVAC system scanned to find which actuator has failed. It is usually a modest repair, and a battery change or disconnect can trigger a relearn.
Hydro-boost relief valve seal may fracture (recall)
- What you'll notice
- Slightly heavier steering when braking or parking, and a brake pedal that needs a little more push to stop the truck.
- Why it happens
- Some hydro-boost brake housings were machined out of spec, which can break the O-ring seal on the relief valve. The trucks did not meet the federal brake standard, so GM recalled them.
- What to do
- Have a dealer check your VIN. The free repair is a new relief valve.
Loose, wandering steering (worn pitman and idler arms)
- What you'll notice
- Steering feels vague or loose at highway speed, the truck wanders in its lane, or the steering wheel has play.
- Why it happens
- The pitman arm and idler arm that connect the steering box to the front wheels wear out under the H2’s weight. Owners often add a heavy-duty reinforcement kit when replacing them.
- What to do
- Have the steering linkage inspected and the front end aligned after any repair. Worn steering parts can also make braking feel unsettled.
Power steering leaks and hard steering
- What you'll notice
- Steering gets hard to turn, especially when parking, power steering fluid drips under the truck, or the pump whines.
- Why it happens
- Leaks at the power steering pump, cooler or hoses let fluid run low. Because the brakes share this fluid (hydro-boost), a leak can also affect braking. GM also recalled some power steering hoses built out of spec.
- What to do
- Check the power steering fluid level and look for leaks. Fix leaks quickly, since low fluid can damage the pump and affect brake assist. Ask a dealer about open hose recalls.
No-start from theft system or ignition switch
- What you'll notice
- The engine cranks but will not start or will not crank at all, sometimes with a security light, then starts after waiting several minutes. The key may stick in the ignition.
- Why it happens
- The Passlock theft-deterrent system and the ignition switch or lock cylinder can fail with wear, so the computer stops fuel or cranking.
- What to do
- Note whether the security light is on when it will not start. A shop can read the theft-system codes; the fix is usually an ignition switch, lock cylinder or Passlock sensor.
Sunroof drains clog and leak water inside
- What you'll notice
- Water drips onto the front floor or seats, the headliner gets wet, or the carpet smells musty after rain.
- Why it happens
- The drain tubes at the corners of the sunroof tray clog with debris, so rain water overflows into the cabin instead of draining out.
- What to do
- Have the sunroof drains cleared and tested. Dry the carpet promptly to prevent mold and damage to wiring under the floor.
Power window falls into door or stops working
- What you'll notice
- A window will not go up or down, makes a grinding noise, or drops down into the door.
- Why it happens
- The window regulator cable or motor in the door fails. Owners report rear windows dropping and getting stuck open.
- What to do
- Tape plastic over the opening to keep rain out until it is fixed. The regulator and motor are often replaced together.
Heated seats turn on by themselves or overheat
- What you'll notice
- A seat heater comes on by itself, will not turn off, or gets very hot; one owner found damaged wiring in the seat cushion.
- Why it happens
- The heated seat element or its control switch and module can fail.
- What to do
- Unplug or fuse off the seat heater until it is fixed if it overheats. Have the heater element and control switch checked.
Front wheel bearing hub failure
- What you'll notice
- A humming or growling noise that rises with speed, play in the wheel, or an ABS warning light.
- Why it happens
- The sealed front wheel bearing and hub assemblies wear out on this heavy truck. One owner had a dealer find bad front bearings after a driving problem.
- What to do
- Have the noise checked; a failing bearing can overheat and let the wheel wobble.
ABS and traction control lights come on
- What you'll notice
- The ABS and traction control lights flicker on and off; in one case gauges, windows and locks lost power at the same time.
- Why it happens
- Faults in the ABS control module or wheel speed sensor wiring set warning lights. GM also recalled some trucks for reversed wheel speed sensor wires.
- What to do
- Have the ABS codes read. Normal braking still works, but ABS and traction control may be off.
Radiator leaks coolant
- What you'll notice
- Coolant spots under the front of the truck, a low coolant warning, or the temperature gauge reading high.
- Why it happens
- The radiator can develop leaks; one 6.2L owner had theirs replaced under warranty.
- What to do
- Top up with the right coolant and watch the gauge. Replace a leaking radiator before the engine overheats.
Crankshaft sensor wiring breaks down
- What you'll notice
- The engine stalls or will not start, sometimes only now and then.
- Why it happens
- The wiring pigtail for the crankshaft position sensor becomes brittle from engine heat and shorts out.
- What to do
- Have the crank sensor and its wiring checked. Repairing the wiring and replacing the sensor is usually a modest job.
Stumbles and stalls right after a cold start
- What you'll notice
- The engine coughs, stutters or stalls right after starting, sometimes with harsh shifting.
- Why it happens
- An owner reported this happening daily on a nearly new 6.2L truck and the dealer found no fix. The cause was not identified.
- What to do
- Have the engine and transmission codes read and ask about software updates. Keep notes of when it happens to help the shop.
Front differential seal and transmission cooler line leaks
- What you'll notice
- Oil spots under the front of the truck or a small leak at the front differential or transmission cooler lines.
- Why it happens
- Seals on the front differential and fittings on the transmission cooler lines can seep, even on low-mile trucks.
- What to do
- Have the leak located and fixed before fluid levels drop, which can damage the differential or transmission.
Paint peeling on rear quarter panels
- What you'll notice
- Paint flakes or peels from the rear quarter panels.
- Why it happens
- Owners of these H2s report paint adhesion failing on the rear quarters.
- What to do
- Repaint the area before the panel starts to corrode under the bare spots.
Front doors freeze shut after rain
- What you'll notice
- Front doors are hard to open or frozen shut in winter after rain or washing.
- Why it happens
- Water collects in the front door jambs and seals and freezes.
- What to do
- Dry the door jambs after washing in cold weather and treat the seals with a silicone protectant.
Repair prices for your Hummer H2
Insufficient verified pricing for this vehicle and repair. We have not yet matched these repairs to two independent, dated price sources for this vehicle, so we show no price, chart or verdict for them.
- Extract broken manifold bolts and replace manifold gasket (one side)
- Remove instrument cluster, send out for rebuild, reinstall
- Replace windshield wiper motor and module assembly
- Replace HVAC mode/blend door actuator
- Replace blower motor resistor and connector pigtail
- Replace rusted brake lines and bleed the system
- Replace front lower ball joints or control arms (both sides)
- Replace pitman arm and idler arm, align front end
- Replace leaking power steering hose or cooler line
- Replace ignition switch or lock cylinder and relearn theft system
- Diagnose airbag system and replace airbag control module
- Clear and test sunroof drain tubes
- Rebuild or replace 4-speed automatic transmission
- Diagnose and rebuild/replace 6-speed automatic
- Replace front differential seal or transmission cooler line
- Replace window motor and regulator assembly
- Refinish rear quarter panel
- Replace seat heater element or control module
- Replace front wheel bearing hub assembly (one side)
- Diagnose ABS codes; replace wheel speed sensor or ABS module
- Repair rusted subframe support or frame section
- Replace fuel pump flow control module
- Replace lifters and related valvetrain parts (or engine)
- Replace radiator
- Replace crankshaft position sensor and repair wiring pigtail
- Diagnose drivability problem (scan, throttle body cleaning, software)
Recall repairs: usually free at the dealer
A dealer can confirm coverage by VIN. An eligible safety recall repair is provided at no charge.
- Recall: inspect wiper motor, install module cover or replace motorNo charge if your vehicle is included
- Recall: test hydro-boost unit and replace if it failsNo charge if your vehicle is included
- Recall: replace hydro-boost relief valveNo charge if your vehicle is included
- Recall: install fused harness or disable heated washer moduleNo charge if your vehicle is included
Disclaimer: Estimates only, not a quote. Ranges are averages built from typical parts prices plus standard book labor time at a typical shop labor rate. Your price will depend on your area, the shop, the parts used and what the shop finds. Dealers often charge more. Diagnosis and taxes are extra.
Pick a model year to see its safety recalls.